Antelope RS4 Manual

Antelope Ikke kategoriseret RS4

Læs gratis den danske manual til Antelope RS4 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 65 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 33 anmeldelser. Har du et spørgsmål om Antelope RS4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Turn left/right to change the level. To Mute, press and hold the

Rotary control knob. Press and hold the knob again to unmute.

To access the Trim Offset feature, press and hold the desired

‘Monitor’ (1, 2, 3 or 4) / ‘Input’ (Ch1,2,3,4,5,6,7 or 8) button. Then,

turn left/right the Rotary Control knob to trim (-6dB to +6dB in 1 dB

steps). Double-click to set to 0 dB.

6. Mono Dim, M/S & Sub

Pressing the Mono button sets the currently selected monitor

output to mono. This button corresponds to the last setting

selected in the Mono effects dropdown menu in the Satori software

control panel.

Press the Dim button to activate the -20dB attenuator. Press once

more to restore normal volume.

When Mono is activated you also have the option to select M/S.

Pressing the M/S button selects either the sum or the difference

between the left and the right channel. This supplies a stereo

effect, which allows you to monitor just the center or just the

periphery of the audio.

Pressing the Sub button activates the LFE output.

7. USB Connector

R4S uses USB connector, Type B.

4. Rear Panel Explained

5. Technical Specications

USB: USB 2.0 Full-Speed interface

on USB Type B connector.

Operating Temperature: 0-50ºC, 32-122º F

Weight (unit): 0.71 kg, 1.57 lb

Dimensions (unit): 220 mm(W) x 55 mm(H) x 85 mm(D)

8.66’’(W) x 2.22 ‘’(H) x 3.31’’(D)

v. July 2015

1. Safety Notes

To reduce the risk of electrical shocks, re, and related hazards:

● Do not remove screws, cover, or cabinet. There are no user

serviceable parts inside. Refer servicing to qualied service

personnel.

● Do not expose this device to rain, moisture or spillover of

liquid of any kind.

● Should any form of liquid or a foreign object enter the

device, do not use it. Unplug the USB Cable. Do not operate

the device again until the foreign object is removed or the

liquid has completely dried and its residues fully cleaned up.

If in doubt, please consult the manufacturer.

● Do not handle the device and USB cable with wet hands!

● Avoid placing things on the cabinet. Risk of falling or

actuating a button.

● If anything goes wrong, turn off the device by unplugging

the USB cable. Do not attempt to repair the device yourself:

consult authorized service personnel or your dealer.

● Do not install near any heat sources such as radiators,

stoves, or other apparatus (including ampliers) that

produce heat.

● Do not use harsh chemicals to clean your unit. Clean only

with specialized cleaners for electronics equipment.

● The device is designed to operate in a temperate

environment, with a correct Operating Temperature of:

0-50 °C, 32-122 °F

2. Installation Guide

It only takes a few moments to harness the benets of the Satori

Remote Control, R4S. Follow these simple steps to connect the R4S

to your system setup:

1. Ensure that you have downloaded and installed the

latest Satori software control panel from the Antelope

Audio website: http://antelopeaudio.com/en/support/

downloads

2. Install the latest rmware update for your Satori device

by clicking on the rmware update button on the ‘Options

Panel’ (of the software control panel).

3. Connect the USB cable between the rear panel of your

R4S device and the computer on which you are running the

Satori software control panel.

4. Turn on the Satori by pressing the power button on the front

panel of the unit or the power button on the software control

panel of the Satori.

Note: R4S is powered by the USB bus and does not require

a separate power supply when connected to a computer.

3. Front Panel Explained

1. SUM Select button

The Sum Select button allows you to send your stereo sum to your

selected monitor output.

2. Input Select buttons, channels 1-8

Input Select allows you to switch between your desired input

source, which will be fed to your selected monitor output.

3. Talkback button

Press the Talkback button to activate the talkback microphone.

This can be distributed to your selected headphones using the

software control panel.

4. Monitor Select buttons 1-4

These allow you to be able to select between the four monitor

outputs. Whatever source is selected will be fed to the selected

monitor out.

5. Rotary control

Large stepped relay attenuator for main monitor output.

Produkt Specifikationer

Mærke:	Antelope
Kategori:	Ikke kategoriseret
Model:	RS4

Har du brug for hjælp?

Hvis du har brug for hjælp til Antelope RS4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Antelope Manualer

Antelope Orion32+ Gen 4 Manual

28 September 2025

Antelope Corefit II Manual

26 August 2025

Antelope Corefit I Manual

26 August 2025

Antelope ZEN QUADRO Manual

16 Juli 2025

Antelope Discrete 4 Pro Synergy Core Manual

9 Juli 2025

Antelope Zen Q Synergy Core Manual

9 Juli 2025

Antelope MRC Manual

7 Februar 2025

Antelope Isochrone Trinity Manual

1 September 2024

Antelope Galaxy 64 Synergy Core Manual

1 September 2024

Antelope RS4 Manual

1 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlas Sound FC-8DRV Manual

28 September 2025

Denon CEOL RCD-N8 Manual

28 September 2025

Victor Pest Electronic Mouse Trap M250 Manual

28 September 2025

Elysia Xpressor NEO QUBE Manual

28 September 2025

Digital Watchdog DWC-PZCM Manual

28 September 2025

Schneider ASISSLC1 Manual

28 September 2025

AVMATRIX SC1221-12G Manual

28 September 2025

Fantech PRO MOUNT MBD1 Manual

28 September 2025

Bebob V200micro Manual

28 September 2025

Ninja Intelli-Sense CT682 Manual

28 September 2025