Apantac SDI-CVBS-S Manual

Apantac Ikke kategoriseret SDI-CVBS-S

Læs gratis den danske manual til Apantac SDI-CVBS-S (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Apantac SDI-CVBS-S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

USER MANUAL

Package Contents

1 CVBS-SDI-S •

1 User manual •

1 Power adapter DC 12V •

1 Mounting plate •

Introduction

This converter is intended for monitoring

use only, not for transmission or on-air use

Features

Auto-detect 3G/HD/SD-SDI input •

Looping SDI output •

RCA Stereo analog audio output •

Coaxial audio output •

SDI-CVBS-S

3G/HD/SD-SDI to CVBS Converter

SPECIFICATIONS

SDI Input 1 x BNC

SDI Loop Out (non-re-

clocked)

1 x BNC

CVBS Output 1 x RCA

Serial Digital SMPTE 424M, 292M, 259M

Equalization

120m at 2.97 Gbps, 140m at 1.48

Gbps, 400m at 270 Mbps with

Belden 1694A

Return Loss > 15db up to 1.485 Gbps

> 10db up to 3G

Embedded Audio SMPTE-272M-A

Composite NTSC (SMPTE-170M), PAL

(ITU624-2)

Signal Level

1V nominal

DC Offset

0V, + - 0.1V

Impedence 75 ohm for BNC, 100 ohm for DVI-I

Return Loss 40db up to 5MHz

Analog Audio Out 2 x RCA

Coaxial (SPDIF) Out 1 x RCA

Analog Audio sample rate 48 KHz

Digital Audio sample rate 48 KHz

Power 12 DC

Weight 3 lbs (1.5 kg)

Dimension (LxWxH) 171 x 119 x 25 mm

FRONT VIEW

1 2 3 4 5 6 7 8

1. RS-232 Control Port

Rx pin: connect to the RxD pin of the RS232

from PC

Tx pin: connect to the TxD pin of the RS232

from PC

GND pin: connect to the GND pin of the RS232

from PC

2. S-Video out Port

3. CVBS (composite video) out Port

4. OSD “Menu” Button (on/off OSD)

5. OSD “Down” Button

6. OSD “Up” Button

7. OSD “Enter” Button

8. Power LED

REAR VIEW

1 2 3 4 5

1. Auto-detect 3G/HD/SD-SDI input

2. Non-reclocked SDI output

3. Coaxial audio output

4. Stereo analog audio output

5. Power Indicator

INPUT VIDEO SUPPORT

Input Frequency

480i 59.94 Hz

576i 50 Hz

720P 50/59.94/60 Hz

1080i 50/59.94/60 Hz

1080P 23.97/24/25/29.97/30/50/59.

94/60 Hz

OSD Operations

Press the “Menu” button, the OSD menu will appear,

press it again to close the OSD and saves all the settings

“Enter” button, this will enter the “EDIT” mode. Change

the values by “up” or “down” buttons, go back by press the

“menu” button

“UP” or “DOWN” button:

The user can select various functions by pressing “up” or

“down” button in the front panel to move the selection bar

RS232 Control Protocol

Baud Rate: 4800bps, 8-bit data, 1 stop bit

The unit will respond following receiving the command

from the server

Command byte Data byte Checksum byte

Byte#0 Byte#1 Byte#2

Command

byte

Data byte ACK type

(from SDI-

CVBS-S)

Funtion

Oxa0 0x00 B Get Model Name

0x01 B Get possible

output resolution

number

0x02 B Get adjustable

video parameter

number

0x03 B Get supported

audio control

0xa1 0x00!0xff A Brigtness

Default: 0x80

0xa2 0x00~0xff A Contrast

Default: 0x80

0xa3 0x00~0xff A Saturation

Default:0x80

0xb0

0x00/0x01 A Output resolution

0: NTSC

1: PAL

Default: 0x00

0xb1

0x00/0x01 A Audio enable

0:off / 1:0n

Default: 0x01

Example:

To set the brightness to be the value 0x02

Server sends: 0xa1, 0x02, 0x5d

SDI-CVBS-S replies: 0xa5, 0x96

SDI-CVBS-S => Server command

Type “A” format

Ack byte Checksum byte Note

0xa5 0x5b Means “ACK”, the unit re-

ceived a valid command

0x6a 0x96 Means “NAK”, the unit

received an unknown com-

mand or data byte that is

out of range

Type “A” ACK format

Type “B” ACK format

Ack byte Checksum byte Note

0xa5 0x5b Means “ACK”, the unit re-

ceived a valid command

0x6a 0x96 Means “NAK”, the unit

received an unknown com-

mand or data byte that is

out of range

ACK byte Length

byte

Data byte checksum

byte

Order Byte#0 Byte#1 Byte#2~Byte#N Byte#N+1

Value 0x5a N+2 0x00~0xff 0x00~0xff

*checksum byte: check sum from Byte#0~Byte#N+1

Example:

To get model of the unit

Server sends: 0xa0, 0x00, 0x60

The unit will respond 0x5a, 0x0a, ‘3’, ‘S’, ‘C’, ‘-’, ‘0’, ‘2’, ‘M’, ‘W’, 0xa0

7470 SW BRIDGEPORT ROAD

PORTLAND, OR 97224, USA

PHONE +1 503 968 3000, FAX +1 503 389 7921

The content of this document are provided in connection with

Apantac LLC (“Apantac”) products. Apantac makes no

representation or warranties with respect to the accuracy or

completeness of the contents of this publication and reserves the

right to make changes to specifications and product descriptions

at any time without notice

Produkt Specifikationer

Mærke:	Apantac
Kategori:	Ikke kategoriseret
Model:	SDI-CVBS-S

Har du brug for hjælp?

Hvis du har brug for hjælp til Apantac SDI-CVBS-S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Apantac Manualer

Apantac EDID-EW-H-II Manual

25 Februar 2025

Apantac SDI-CVBS-S Manual

31 August 2024

Apantac Micro-Single Manual

31 August 2024

Apantac MicroQ Manual

31 August 2024

Apantac HDM2.0-FIB-II-HID-SM Manual

29 August 2024

Apantac HDBT-1-R Manual

29 August 2024

Apantac DA-HDTV-SDI-UHD Manual

29 August 2024

Apantac SDI-FIB Manual

29 August 2024

Apantac DP-FIB Manual

29 August 2024

Apantac EDID-EW-H Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Ambient Weather WS-1173A Manual

18 September 2025

Vestil APTS-2460 Manual

18 September 2025

Frilec KOBLENZ9314-340 Manual

18 September 2025

Lanaform Aqua Pleasure Manual

18 September 2025

Ambient Weather WS-2902D Manual

18 September 2025

Emerson CKS1702 Manual

18 September 2025

Vestil BOL-48-5.5 Manual

18 September 2025

Ambient Weather WS-HE01 Manual

18 September 2025

Ambient Weather TransformaFence Manual

18 September 2025

Ambient Weather EZ-48-3AB-125-35 Manual

18 September 2025