Apantac SDI-FIB Manual

Apantac Ikke kategoriseret SDI-FIB

Læs gratis den danske manual til Apantac SDI-FIB (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Apantac SDI-FIB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1. SDI-FIB-Tx: SDI to Fiber transmitter w/ DC5V

1.5A Power Supply

2. SDI-FIB-Rx: Fiber to SDI receiver w/ DC5V

1.5A Power Supply

3. DC 5V 1.5A Power Supplies

4. Options: 12V XLR male to mini XL female

cable for direct power from the camera

5. User Manual

6. Pelican like hard carrying case

Product Specification

 Transmission of Multi-rate SDI (3G/HD/SD-

SDI) video over a single fiber. (SMPTE-

424M, SMPTE-292M and SMPTE-259M)

 Compatible with single-mode or multi-mode

fiber

 Equalized on the inputs and reclocked on the

output to maximize performance up to 120m

for 3G and 140m for HD-SDI

 Extension limit: 18 mile (30 km) for 1.485

Mbps, 12.5 miles (20 km) for 3G (1080P)

 Recommended fiber optic cable: Glass single

-mode fiber with 1310, 1550nm with ST ter-

minated connectors

 General Electrical specifications

 Link power budget: Minimum 11dB

 BNC connectors: 75 ohm male

 Mechanical specifications

 Dimension: 19.5mm x 19.5mm x 82.7mm

(WxHxD)

 Environmental Specifications

 Operating temperature: -20C to 70C

 Storage temperature: -30C to 85C

 Humidity: 5% to 95% RH

MAZAMA

SDI-FIB

Installation and

Apantac LLC

7556 SW Bridgeport Road

Portland, OR 97224

T: +1 (503) 968 3000

F: +1 (503) 389 7921

E: info@apantac.com

3G/HD/SD-SDI to Fiber Extender

Mazama SDI-FIB 0817

What’s in the Box

DC Power Adaptor Pin-out

Startup and Installation

(1) Unpack the content from the hard carrying

case

(2) Connect the SDI-FIB-Tx’s BNC side to the SDI

source. (Note: It is recommended to connect

the BNC directly to the source. Any interme-

diate cables or barrows may impact the signal

performance)

(3) Plug the +5V DC power adaptor to SDI-FIB-

(4) Connect the SDI-FIB-Rx’s BNC to the display.

(Note: It is recommended to connect the BNC

directly to the source. Any intermediate ca-

bles or barrows may impact the signal perfor-

mance)

(5) Plug the +5V DC power adaptor to SDI-FIB-

Connection Diagram

Produkt Specifikationer

Mærke:	Apantac
Kategori:	Ikke kategoriseret
Model:	SDI-FIB

Har du brug for hjælp?

Hvis du har brug for hjælp til Apantac SDI-FIB stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Apantac Manualer

Apantac OG-US-4000 Manual

6 November 2025

Apantac DA-SDI-HDTV Manual

5 November 2025

Apantac OG-US-5000 Manual

5 November 2025

Apantac DA-SDI-DE Manual

29 September 2025

Apantac EDID-EW-H-II Manual

25 Februar 2025

Apantac SDI-CVBS-S Manual

31 August 2024

Apantac Micro-Single Manual

31 August 2024

Apantac MicroQ Manual

31 August 2024

Apantac HDM2.0-FIB-II-HID-SM Manual

29 August 2024

Apantac HDBT-1-R Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM LMC840 Manual

20 December 2025

IFM SMF150 Manual

20 December 2025

Ecler VEO-XCTRL4D Manual

20 December 2025

Brondell SMB-25 Manual

20 December 2025

Delta H71PB Manual

20 December 2025

Kichler 4D12V27 Manual

20 December 2025

JILONG KL-33F Manual

20 December 2025

Govee H7075 Manual

20 December 2025

Signature Hardware Greyfield 481138 Manual

20 December 2025

Aqprox appTPV00 Manual

20 December 2025