APC Back-UPS 500VA Manual

APC Uafbrydelig strømforsyning (UPS) Back-UPS 500VA

Læs gratis den danske manual til APC Back-UPS 500VA (8 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 19 anmeldelser. Har du et spørgsmål om APC Back-UPS 500VA, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Place the Back-UPS to avoid:

– Direct sunlight

– Excessive heat

– Excessive humidity or contact with fluids

bu054a

ON/OFF and

LED Status

Indicator Battery backup and

surge protected outlets

All other trademarks are property of their respective owners.

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

Connect the Battery and Turn on the Unit

Connect the battery to the UPS before use. To connect the battery:

 Pull the top of the battery connector lever out of the unit, until the lever is horizontal.

 Push the battery connector lever completely into the unit, until the end of the lever is flush with the rear panel.

Press ON/OFF to turn on the unit.

A single short beep, and the green “Power On” indicator confirms that the Back-UPS is on and ready to provide

protection.

The Back-UPS should charge for at least 10 hours to ensure sufficient runtime. The unit is being charged

whenever it is connected to utility power, whether the unit is turned ON or OFF.

Status Indicators

The Back-UPS indicates its operating status using a combination of visual and audible indicators.

Power On LED Buzzer Condition

On Off On-line - Back-UPS is supplying conditioned utility power

to the connected equipment

On (Off during 4

beeps) 4 beeps repeated

every 30 seconds

On-Battery - Back-UPS is supplying battery power

Flashing Rapid Beeping

(every 1/2 second)

Low Battery Warning - The Back-UPS has 1.5 minutes of

remaining battery power

Flashing Constant tone Bad Battery Detected - Battery needs to be charged, or is

at end of life. (See Battery Replacement.)

Off Short beep every

4 seconds

Low Battery Shutdown - During On Battery operation the

battery power was almost completely exhausted, and the

Back-UPS is waiting for utility power to return to normal

Off Constant Tone On Battery Overload - Connected equipment requires

more power than provided by the Back-UPS battery.

Unplug devices one at a time to remove overload, if not

corrected Contact APC Technical Support

On Constant Tone On Line Overload - The power drawn by the connected

equipment exceeds the power capacity of the Battery

Backup

Flashing Chirp every 2

seconds

Charger Warning -Back-UPS has experienced an internal

problem, but continues to power the load. Contact APC

Technical Support

Off Constant Tone Charger Fault - Back-UPS has an internal problem, and is

no longer powering the load. Contact APC Technical

Support

Adjusting Transfer

Voltage and Sensitivity

Settings

Automatic Voltage Regulation boosts the utility voltage

when it drops below safe levels. This allows the

equipment plugged into the unit to operate during low

voltage conditions, conserving the battery power in the

event of a power outage.

The Back-UPS will switch to battery power if the input

voltage level becomes too low for the Automatic

Voltage Regulation to compensate, or if the utility

power is distorted.

If the Back-UPS switches to battery power too

frequently or too infrequently, adjust the transfer

voltage and sensitivity settings:

1. Ensure the Back-UPS is off. Plug it into utility

power.

2. Press and hold ON/OFF until the LED repeatedly

flashes. The unit is now in Program Mode.

3. Release the button. The LED will flash once,

twice, or three times per second, indicating the

current setting. See Transfer Voltage and

Sensitivity Settings.

4. Press ON/OFF within two seconds to change the

setting. Each time the button is pressed, the LED

will flash at a different rate: once, twice, or three

times per second, indicating the new setting.

Continue pressing the button until the desired

setting is reached. If the button is not pressed

within five seconds, the Back-UPS will exit the

Program Mode.

5. To exit Program Mode, release the button and

wait for the LED to stop flashing.

Connect Equipment

Battery Backup Surge Protection

These outlets are powered whenever the Back-UPS is switched

ON. During a power outage, or other utility problems (brownouts,

over-voltages), these outlets will be powered for a limited time by

the Back-UPS. Plug the computer and monitor into these two

outlets.

Connect AC Power Cord

Plug the Back-UPS power cord into a wall outlet, not a surge

protector or power strip. The outlet should be near the equipment

and easily accessible.

Back-UPS® RS 500

BR500CI-AS User Guide

Transfer Voltage and Sensitivity Settings

LED Flashing Transfer Voltage

Setting

Input Voltage

Range

(For Utility

Operation)

Usage

Once per second Low 155 - 280 The Back-UPS will switch to battery power less often. Use with equipment that is not

sensitive to low or high level voltage levels or minor voltage waveform distortions.

Twice per second Medium

(factory default) 160 -280 Default, use in normal conditions.

Three times per second

High 165 - 270 The Back-UPS will switch to battery power during any small fluctuation in voltage.

Use with equipment that is sensitive to low or high level voltage levels or minor

voltage waveform distortions.

bu053a

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	Back-UPS 500VA
Bredde:	115 mm
Dybde:	213 mm
Højde:	185 mm
Vægt:	4900 g
Produktfarve:	Sort
Pakkevægt:	5500 g
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Mini Tower
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Udgangseffekt:	300 W
LED-indikatorer:	Strøm
Kabellængde:	1.8 m
Pakkens dimensioner (BxDxH):	190 x 291 x 257 mm
Opladningstid for batteri:	10 t
Bæredygtighedscertifikater:	RoHS
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 15000 m
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Strømstik:	C14 forbinder
AC udgange, antal:	4 AC stikkontakt(er)
AC stikkontakt typer:	C13 forbinder
Overspænding energivurdering:	240 J
Indgående driftsspænding (maks.):	230 V
Output strømkapacitet (VA):	0.5 kVA
Indgående driftsspænding (min.):	- V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	230 V
Beskyttelse ved overspænding:	Ja
Typisk backup tid ved halv styrke:	1 min.
Typisk backup tid ved fuld styrke:	70 min.
Antal indgående faser:	1
Antal udgående faser:	3
Output tilslutningstype:	IEC 320 C13