APC Back-UPS BN600G Manual

APC UPS Back-UPS BN600G

Læs gratis den danske manual til APC Back-UPS BN600G (2 sider) i kategorien UPS. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om APC Back-UPS BN600G, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Inventory

Safety and General Information

Inspect the package contents upon receipt. Notify the

carrier and dealer if there is any damage.

Read the Safety Guide supplied with this unit before

installing the UPS.

• This UPS is intended for indoor use only.

• Do not operate this UPS in direct sunlight, in contact with fluids, or where there is

excessive dust or humidity.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper

ventilation.

• The battery typically lasts for three to five years. Environmental factors impact

battery life. Elevated ambient temperatures, poor quality AC power, and frequent

short duration discharges will shorten battery life.

• Connect the UPS power cable directly to a wall outlet. Do not use surge protectors

or extension cords.

Specifications

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop!

Connect the Battery” label that covers the outlets. Prior to connecting any equipment

to the unit, connect the battery cable to the unused battery terminal. It is normal for

small sparks to be seen when the battery cable is connected to the battery terminal.

Wall Mount Installation

• Horizontal installation, use 2 screws 7.3" (186.3 mm) apart.

• Vertical installation, use 2 screws 5.4" (137.2 mm) apart.

• Allow 5/16” (8 mm), of the screw to protrude from the wall.

Replace Battery

Deliver the used battery to a recycling facility.

Replace the used battery with an APC by Schneider Electric approved

battery. Replacement batteries can be ordered through the APC by

Schneider Electric Web site, www.apc.com. Battery replacement part for

Back-UPS BN600G is APCRBC110.

Connect Equipment

Battery Backup + Surge Protection Outlets

Battery backup outlets provide protection to connected equipment when the

Back-UPS is turned on and connected to AC power.

Battery backup outlets receive power from the Back-UPS for a limited period of time

when a power outage, or brownout condition occurs.

Battery backup outlets provide protection from power surges or spikes.

Connect a computer, monitor and other peripheral devices to the outlets.

Surge Protection Outlets

Surge protection outlets provide protection to connected equipment when the

Back-UPS is connected to AC power, and is switched on or off.

Surge protection outlets provide protection from power surges or spikes.

Connect a printer, scanner or other peripheral devices that do not need to remain on

during power outages, or AC problems to the surge protection outlets.

Connect Network

The Back-UPS protects equipment connected to a 10/100 Base-T ethernet, from

power surges when connected through the Back-UPS dataline protection jacks.

PowerChute™ Personal Edition Software

Overview

Use PowerChute Personal Edition software to configure the UPS settings.

Protect your computer and other equipment during a power outage. During a power

outage, PowerChute will save any open files on your computer and safely shut it

down. When power is restored, it will restart the computer.

Configure the UPS to use features such as power-saving outlets, shutdown

configuration, and alarms.

Monitor the UPS for power usage and power events.

Note: PowerChute is only compatible with a Windows operating system. If you are

using a Mac OSX, use the native shutdown feature to protect your system. See the

documentation provided with your computer.

Installation

Use a USB cable to connect the Data port on the rear panel of the UPS to the USB port

on your computer.

If the Back-UPS came with CD into your computer and a PowerChute CD, insert the

follow the on-screen instructions

If the Back-UPS did not come with a PowerChute CD, go to www.apc.com and

download the software free of charge.

Turn On the Back-UPS

Press the POW ER ON button located on the top of the Back-UPS. The Power On/

Replace Battery LED will illuminate and a single short beep will be audible to

indicate that the Back-UPS is providing protection for connected equipment.

The Back-UPS battery charges fully during the first 16 hours while connected to AC

power. The Back-UPS battery will charge while the Back-UPS is switched on or off

and is connected to AC power. Do not expect full battery run capability during the

initial charge time.

If the red Building Wiring Fault LED located on the side of the Back-UPS

illuminates, do not operate the Back-UPS. Have a qualified electrician correct the

building wiring fault.

Warranty

The standard warranty is three (3) years from the date of purchase. Schneider Electric

IT (SEIT) standard procedure is to replace the original unit with a factory

reconditioned unit. Customers who must have the original unit back due to the

assignment of asset tags and set depreciation schedules must declare such a need at

first contact with an Schneider Electric IT (SEIT) Technical Support representative.

SEIT will ship the replacement unit once the defective unit has been received by the

repair department, or cross ship upon the receipt of a valid credit card number. The

customer pays for shipping the unit to SEIT. SEIT pays ground freight transportation

costs to ship the replacement unit to the customer.

Input

Voltage 120 Vac Nominal

Frequency 47 - 63 Hz

Brownout Transfers 92 Vac Typical

Over-voltage Transfer 139 Vac Typical

Output

UPS Capacity

(4 battery backup outlets)

BN600G: 600 VA, 360 W

Total Amperage (all outlets) 12 A (including UPS output)

Voltage - On Battery 115 Vac ± 8%

Frequency - On Battery 50 / 60 Hz + 1

Transfer Time 6 ms Typical, 10 ms maximum

Protection

and

Filtering

AC Surge Protection Full time, 340 Joules

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery

Type Sealed, maintenance-free, lead acid

BN600G: RBC110

Typical Recharge Time 24 hours

Average Life 3 - 5 years depending on the number of

discharge cycles and environmental

temperature

Physical

Net Weight Replacement battery cartridge

BN600G: 12 lb (5.5 kg)

Dimensions

Length x Width x Height

12 in x 7 in x 3 in

30 cm x 18 cm x 9 cm

Operating Temperature 32º F to 104º F (0º C to 40º C)

Storage Temperature 5º F to 113º F (–15º C to 45º C)

Operating Relative Humidity 0 to 95% non-condensing humidity

Operating Elevation 0 to 10,000 ft (0 to 3000 m)

EMC

Compliance

This device complies with part 68 and part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired

operation.

Locate the label on the bottom of this device that contains, among other

information, the FCC registration number and ringer equivalence

number (REN) for this device. If requested, this information must be

provided to the telephone company.

If you experience trouble with this equipment, you disconnect it from the

network until the problem has been corrected or until you are sure that

the equipment is not malfunctioning.

The ringer equivalence number (REN) is used to determine how many

devices can be connected to your telephone line. In most areas, the sum

of the RENs of all devices on any one line should not exceed five (5.0).

If too many devices are attached, they may not ring properly.

 Press the battery compartment cover

release tab located on the rear side of the

unit. Slide the battery cover off.

 Connect the battery cable securely to the

battery terminal.

 Reinstall the battery compartment cover.

Be sure that the release tab locks into place.

bu075c

ack-U P

bu064c

bu065c

bu066c

bu202a

Back-UPS

Battery Backup + Surge Protection

Surge Protection

bu201a

CAUTION-Refer to bottom

of unit for safety markings.

Circuit

Breaker

Building

Wiring Fault

PowerChute

USB Port

Network

Out

Push to

Reset

Network

User Manual Back-UPS™ BN600G

Produkt Specifikationer

Mærke:	APC
Kategori:	UPS
Model:	Back-UPS BN600G

Har du brug for hjælp?

Hvis du har brug for hjælp til APC Back-UPS BN600G stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

UPS APC Manualer

APC RBC150 Manual

2 April 2025

APC RBC151 Manual

2 April 2025

APC Symmetra LX 4kVA Manual

30 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

29 Marts 2025

30 Januar 2025

30 Januar 2025

APC BE650G2-IT Manual

14 Januar 2025

UPS Manualer

Nyeste UPS Manualer

Teltonika BAT120 Manual

30 Januar 2025

LevelOne UPS-2101 Manual

9 Januar 2025

Conceptronic ZEUS52E6K Manual

31 December 2025

Conceptronic ZEUS51E6K Manual

31 December 2025

CyberPower Smart App Sinewave PR2000RT2U Manual

30 December 2025

Tripp Lite ECO750UPS Manual

30 December 2025

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/10 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/20 Manual

28 December 2024

Phoenix Contact QUINT-UPS/ 24DC/ 24DC/ 5 Manual

28 December 2024

Conceptronic ZEUS52EA3K Manual

14 December 2024