Apollo Ultrasonic Visual Manual

Apollo Ultrasonic Måleudstyr Visual

Læs gratis den danske manual til Apollo Ultrasonic Visual (2 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Apollo Ultrasonic Visual, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

APOLLO VISUAL OIL MONITOR INSTRUCTIONS

www.dunravensystems.com Ver122014

The Apollo Visual product consists of:

 1 x Apollo Ultrasonic Tank Transmitter

 1 x Apollo indoor receiver plug

 2 x Stainless steel tting screws

 1 x Weather seal

Step 4 - Fitting the transmitter (after matching)

The procedure is the same for tting to both old and new tanks.

For Tank with pre-drilled

30/32mm hole

- Remove the cap from the hole

and insert transmitter, ensuring

the weather seal is securely in

place.

- Ensure the transmitter is vertical

on top of the tank

-Tighten on to the tank using the 2 stainless steel 19mm long self –

tapping screws supplied. Do not use longer screws. Do not over

tighten.

For Tank without a predrilled hole a

- tank is not predrilled, then using a 30/32mm hole saw, drill a If a

hole in the top of tank in suitable area to allow ease of tting the

transmitter and in an area that the transmitter can see the tanks

contents. Position so that there are no internal obstructions.

(i.e. ribs, stays, side of ta , internal equipment) that might nk

interfere with the ultrasonic signal. Ensure the transmitter is a

minimum of 10cm from any tank wall or edge.

- Use the Install Help diagram to insure suitable tting.

- Ensure the transmitter is vertical on top of the tank.

- Tighten on to the tank using the 2 stainless steel 19mm long

self tapping screws supplied. Do not use longer screws. Do –

not over tighten. You have now completed the installation.

Always set switch 1 up to

enable the low level audible

warning.

Step 1: Setting your receiver

plug

Measure your tank height,

from the base of the tank to

the base of the Apollo

transmitter location. Using the

Setting table provided on the

right, select the height closest

to your tank height.*NB. On a

bunded tank measure the

inner tank height*

Refer to the lower height

available.

E.g. if your tank height is

975mm choose the setting of

950mm on the table.

Set your pins to the required

setting. E.g. 1400 mm height

pins 1,3,5,6,8 in the up

position.

Step 2: Choosing a suitable

electrical socket

Choose a suitable electrical

socket, located in closest

proximity to the tank. The area

should be free of other

electrical appliances, wiring

and any large steel or metal

devices which could hinder the

FM signal between the tank

transmitter and receiver. Plug

your receiver plug into the

socket and switch on - the top

bar will ash to indicate the

unit is in learn mode and

ready for matching. This bar

will continue to ash for a

period of 2 Minutes.

Step 3: Matching the units

Note the black dot on the right

hand side of the receiver. Note

the black dot on the left hand

side of the tank transmitter.

Whilst the top bar is ashing

on the receiver hold the tank

transmitter against the

receiver as shown, so that the

black dots are aligned with the

display screens facing you, as

shown. Hold together. The

bars will increase up the

display screens. ONLY when

all 10 bars are shown, will they

ash to indicate that, the

unique code is transferred and

the units are matched.

Remove the transmitter from

the monitor immediately once

all 10 of bars are reached.

Tank

Height mm

Pin Settings

in up position

Tank Height

Settings in up

position

500

1750

1,3,4,5,6,7

550

1,7

1800

1,2,8

600

1,6,8

1850

1,2,7,8

650

1,6,7,8

1900

1,2,6,7

700

1,5,7

1950

1,2,5

750

1,5,6

2000

1,2,5,7,8

800

1,5,6,7,8

2050

1,2,5,6,8

850

1,4,8

2100

1,2,4

900

1,4,6

2150

1,2,4,7

950

1,4,6,7

2200

1,2,4,6,8

1000

1,4,5,8

2250

1,2,4,6,7,8

1050

1,4,5,7,8

2300

1,2,4,5,7

1100

1,4,5,6,7

2350

1,2,4,5,6

1150

1,3

2400

1,2,4,5,6,7,8

1200

1,3,7,8

2450

1,2,3,8

1250

1,3,6,8

2500

1,2,3,6

1300

1,3,5

2550

1,2,3,6,7

1350

1,3,5,7

2600

1,2,3,5,8

1400

1,3,5,6,8

2650

1,2,3,5,7,8

1450

1,3,5,6,7,8

2700

1,2,3,5,6,7

1500

1,3,4,7

2750

1,2,3,4

1550

1,3,4,6

2800

1,2,3,4,7,8

1600

1,3,4,6,7,8

2850

1,2,3,4,6,8

1650

1,3,4,5,8

2900

1,2,3,4,5

1700

1,3,4,5,6

3000

1,2,3,4,5,6,8

Thank you for purchasing the Apollo Visual Oil Level Monitor

Pin Setting Table

Produkt Specifikationer

Mærke:	Apollo Ultrasonic
Kategori:	Måleudstyr
Model:	Visual

Har du brug for hjælp?

Hvis du har brug for hjælp til Apollo Ultrasonic Visual stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måleudstyr Apollo Ultrasonic Manualer

Apollo Ultrasonic Visual Manual

22 August 2024

Apollo Ultrasonic Smart Alarm Manual

22 August 2024

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025