APPS2Car M02-T2 Manual

APPS2Car Ikke kategoriseret M02-T2

Læs gratis den danske manual til APPS2Car M02-T2 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 2 anmeldelser. Har du et spørgsmål om APPS2Car M02-T2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTALLATION GUIDE

Step 1

- 1 - - 2 -

- 3 - - 4 -

Unscrew the ﬁxed nut completely. Let the ball joint pass

through the ﬁxed nut (the thread must face to the groove).

Step 3

Cl th dashboard w th d loth.ean e i ry c

Step 5

Let it sit for at least 24 hours before using to achieve

the strongest adhesion.

Step 4

Put the magnetic mount on the dash and ﬁrmly press

it. Hold in place for about 30 seconds.

Step 6

Once the mount is secured in place, remove the protective

ﬁlm and set the Metal Plate.

You may place the metal plate as following shows.

Installation between the case and device

Removal Paper

Metal Plate

Scratch Protective Film

Opition 1

Installation on the back of device

Opition 2

Installation on the back of the case

Opition 3

1 2

Step 2

Push the ball joint ﬁrmly into the groove on the back of the car

mount, then tighten the ﬁxed nut.

Magnetic Car Mount

On The Dashboard

MT01

Y O U R B E S T D R I V E P A R T N E R

User Manual

Dear Customer

please do not hesitate to

If you have an stiy que on

we are always here if you need!

ATTENTION!!

- 5 -

- 6 -

Use a thin plastic card

to carefully lift the

dashboard pad from

the mounting surface.

Slowly lift up and

remove it.（Remember

not too hard and

move it slowly）

Tips 2

Remove Dashboard Disk Pad

Tips 1

Viscosity of VHB Sticky Tape

Time of Viscosity

①Cleaning the ﬂat surfaces to ensure that there is no

dust or oil.

②Do not leave ﬁngerprints on the 3M sticky tape.

③When applying, please make sure that the

temperature of the ﬂat surface and the sticky gel

should be above 68℉, or you may soften the 3M VHB

tape under heating air before installation.

④Press for 8 to10 seconds after pasting.

⑤ Recommended to use after of pasting. 24 hours

⑥Never uses the adhesion promoter on the metal

surface.

For better pasting, please kindly note:

Produkt Specifikationer

Mærke:	APPS2Car
Kategori:	Ikke kategoriseret
Model:	M02-T2

Har du brug for hjælp?

Hvis du har brug for hjælp til APPS2Car M02-T2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret APPS2Car Manualer

APPS2Car M02-T2 Manual

3 December 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

JET JAT-450 Manual

4 December 2025

Audio-Technica AT-HPC3 Manual

4 December 2025

Media-Tech Ozone Pro+ MT6539 Manual

4 December 2025

JET JCT-3643 Manual

4 December 2025

Draper 34570 Manual

4 December 2025

Advantech ADAM-4051 Manual

4 December 2025

SPT SU-1054 Manual

4 December 2025

Williams Sound PPA R38 Manual

4 December 2025

ELO E119034 Manual

4 December 2025

ELO E432771 Manual

4 December 2025