Argon BASS12 Manual

Argon Subwoofer BASS12

Læs gratis den danske manual til Argon BASS12 (5 sider) i kategorien Subwoofer. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Argon BASS12, eller vil du spørge andre brugere om produktet?

Side 1/5
12 & 15
01 OWNER’S MANUAL
04 ILLUSTRATIONS
05 SPECIFICATIONS
05 TROUBLESHOOT
Owner ’s manual
Dear Customer,
Quality has always been our driving force and
founding Argon Audio is a natural extension of
this philosophy.
We have 20 years’ experience in creating and
specifying high quality products,
manufacturing them and selling them on to
end users with Value Money as the -for-
primary aim. And Argon Audio is a brand fully
compliant with these values.
Design, features and quality standards are all
specified in Denmark and manufacturing takes
place in the Far East, where quality vendors
are highly competitive and as a result supply -
outstanding Value Money products- -for
– to the delight of both ourselves and our
customers!
Introduction
Thank you for choosing Argon Audio
Subwoofer, we hope will bring you many it
years of enjoyment.
Please read this manual fully before
unpacking and installing the product.
Argon BASS -12/15 is manufactures with a no
nonsense approach. is without BASS 12/15
any unnecessary gimmicks, bling bling or
fancy features. The money is spent on quality
components, efficient woofer driver and
extremely solid cabinet. Quality features you
only see on products twice the price of an
Argon BASS . 12/15
Unpacking
We have during production and packing
carefully this checked and inspected
Subwoofer.
After unpacking please check for any damage
from t ransport. We recommend that you keep
the original carton box and packing material
for any future shipping.
12&15
Subwoofer installation
The Subwoofer requires connection to the
mains power supply, so for your safety it is
important that you read both this manual and
the amplifier manual before connecting.
Subwoofer positioning
Variations in placement of loudspeakers can
produce dramatic differences in the way music
sounds. No listening room is the same and
therefore we encourage you to spend some
time experimenting with which placements
work best in your listening room. Positioning
of Subwoofers is however less critical
compared with full-range loudspeakers
because the low frequencies reproduced by a
subwoofer can be difficult to locate in the
room. You can start with our basic
recommendations.
To begin with, if you use the Subwoofer in a
surround set the S-up, ubwoofer should ideally
be positioned between the TV and one of your
front loudspeakers, as fig. 2 to 4 on page 5. If
you are using the Subwoofer in a stereo set-
up the Subwoofer should ideally be positioned
between the two front stereo speakers, as
fig.1on page 5.
You should know that, if the Subwoofer is
placed close to a wall or in a corner, the bass
sound will be enhanced.
It’s your choice what you like the most.
Another example is the placement of the
Subwoofer in the middle of the stereo
speakers or away from the center of the
stereo speakers.
This may have an impact on how you perceive
the stereo image, even though its only low
frequency sounds that come from the
Subwoofer.
Trust your ears and be willing to experiment
freely.
(Almost) everything is possible
Running-in period
We recommend a running-in time of your new
BASS S -12/15 ubwoofer of approximately 15
20 hours at normal listening
level before you decide on the final positioning
and control settings of the Subwoofer . During
the running-in time the drive units will settle in
and perform as intended.
Connecting your Subwoofer
We recommend that you read the manual of
your A receiver carefully before mplifier or AV-
connecting your Subwoofer.
First switch off the Amplifier and all equipment
before you connect the Subwoofer.
Connect your Amplifier/av-reciever’s
SUB OUT-OUT or PRE- to either INPUT
right/left (1 or 2) as shown on page 4.
If you use a Stereo Amplifier it’s
recommended to use the INPUT right/left
connections (1) as shown on page 4.
If you use a AV receiver with a SUB out it’s
recommended to use the LFE connection (2)
on page 4.
When finished, connect the subwoofer power
cable ( as shown on page 9) 4 to the mains
voltage and, push the POWER ON/OFF
button (10 as shown on page ) 4 to ON
position, the indicator lamp POWER LED will
now glow blue and the ubwoofer is active S
and ready to be used.
The Argon ubwoofer has a BASS 12/15 S
built-in AUTO STANDBY function ( 9) as
shown on page 4 and after approximately 20
minutes ignal, without any input s , the
subwoofer will automatically switch off, and
the indicator lamp POWER LED will change
color. When an input signal is detected the
subwoofer will become active and the
indicator lamp POWER LED will glow blue.
Setting volume, frequency and phase
The volume, crossover and phase (controls 4,
5 and 7) as shown on page 4, can be adjusted
on the rear panel, and we recommend that
you adjust the setting of these controls to your
liking – try with different music and films.


Produkt Specifikationer

Mærke: Argon
Kategori: Subwoofer
Model: BASS12

Har du brug for hjælp?

Hvis du har brug for hjælp til Argon BASS12 stil et spørgsmål nedenfor, og andre brugere vil svare dig