ASI TURBO-Pro 10-0196-1-41 Manual

ASI Ikke kategoriseret TURBO-Pro 10-0196-1-41

Læs gratis den danske manual til ASI TURBO-Pro 10-0196-1-41 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 81 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 41 anmeldelser. Har du et spørgsmål om ASI TURBO-Pro 10-0196-1-41, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

PLEASE CAREFULLY READ THROUGH THIS MANUAL BEFORE USING THE PRODUCT.

OBSERVING ALL SAFETY INFORMATION, WARNINGS AND CAUTIONS WILL PROTECT

YOURSELF AND OTHERS. PLEASE KEEP INSTRUCTIONS FOR FUTURE REFERENCE.

www.americanspecialties.com

AMERICAN SPECIALTIES, INC.

441 Saw Mill River Road, Yonkers, NY 10701 (914) 476-9000

MODEL # 0196-1

MODEL # 0196-2

MODEL # 0196-3

DIM’S

inch[mm]

ITEM CATEGORY

Operating Voltage, 0196-1

Operating Voltage, 0196-2

Operating Voltage, 0196-3

Output Warm Air Volume

Output Warm Air Temp

Output Air Speed

Sound Pressure

Motor Type

Motor Thermal Protection

Heater Element

Heater Thermal Protection

Drying Time

Standby Power

Circuit Operation

Sensor Range

Timing Protection

Timing Duration

Cover Type

Cover Finish

Net Weight

Shipping Weight

Unit Size

PERFORMANCE DATA

TECHNICAL SPECIFICATIONS

120 VAC, 50/60 Hz, 1.0 kW

240 VAC, 50/60 Hz, 1.0 kW

277 VAC, 60 Hz, 1.0 kW

32 - 42 CFM {55 - 72 m³/h}, Adjustable by Owner

131°F {55°C} at ambient T = 77°F {25°C}, MAX, Adjustable by Owner

208 mph (305 ft/s) [93 m/s {335 km/h}] - 257 mph (378 ft/s) [115 m/s {414 km/h}], Adjustable by Owner

68 to 73.8 dB-A @ 2m, Adjustable by Owner

0.67 HP, 16 - 29 krpm, Adjustable, Brush Type, Dual Ball Bearings

120 VAC, Auto Resetting Thermostat turns unit off at 203°F {95°C}

240 VAC, Auto Resetting Thermostat turns unit off at 203°F {95°C}

ON/ OFF Heating options; Range Adjustable by Owner, 325 - 500 W

Auto Resetting Thermostat turns heater element off at 185°F {85°C}, Resets at

167°F {75°C},Thermal cut-off at 288°F {142°C}

Less than 15 seconds

Less than 0.5W

Infrared Automatic, self adjusting

Standard 6-11/16" ± 25/32" [170 ± 20] , Adjustable, range 3-15/16" to 9-1/16" [100 to 230]

60 seconds auto shut off

2 seconds delayed turn off after last sensor read

18 gauge (.047" [1.2]) thick drawn steel or 304 series stainless steel

Powder coating white or matte black on steel or satin on stainless steel

9.3 lbs {4.2 kg}

10.4 lbs {4.7 kg}

8-5/8" W x 13-9/16" H x 4" D [219 x 345 x 101]

1705120000 Rev C 05 July 2018

Patented

8-5/8″

[219]

4″

[101]

13-9/16″

[345]

Operating Instructions and Parts Manual

Hand Dryer Surface-mounted -compliant hand dr yer ADA

2www.americanspecialties.com

VAC

110

115

120

208

220

230

240

277

Motor Heater

Vac

110

115

120

208

220

230

240

Inrush A(W)

5.73 (630)

5.99 (689)

6.25 (750)

2.71 (563)

2.86 (630)

2.99 (689)

3.13 (750)

Operating A (W)

3.82 (420)

3.99 (459)

4.17 (500)

1.81 (376)

1.91 (420)

2.00 (459)

2.08 (500)

3.82 (420)

3.99 (459)

4.17 (500)

1.81 (376)

1.91 (420)

2.00 (459)

2.08 (500)

Vac

110

115

120

208

220

230

240

Total

Inrush A(W)

9.55 (1050)

9.98 (1148)

10.42 (1250)

4.51 (939)

4.77 (1050)

4.99 (1148)

5.21 (1250)

Operating A(W)

7.64 (840)

7.99 (918)

8.33 (1000)

3.61 (751)

3.82 (840)

3.99 (918)

4.17 (1000)

№

0196-1

0196-2

0196-3

ModelInput

Operating A(W)

Installation

1. Make sure power supply breaker is switched off. Installation must be carried out in accordance with

the current edition of the local wiring regulations code having jurisdiction. Installation should be

performed only by a qualified electrician.

2. Place template against wall at desired height (see mounting height recommendations) and mark

locations of 4 mounting holes and wire service entry at knockout (KO) location.

For two or more dryers, dryers should be no closer than 24" [610] on center.Note:

3. Remove and retain two (2) Main cover screws and Main cover.

4. a. For in-wall (concealed) power supply - (See MT & IG 1705120001)

Provide supply wire to KO location according to local code and attach securely to chassis at KO

with appropriate strain relief connector (not supplied).

b. For Surface Mounted Conduit (exposed) power supply -

Provide appropriate conduit to entry location according to local code and attach securely to chassis

with correct strain relief connector (not supplied).

5. Drill four (4) holes at locations A, B, C and D of 5/16" Diameter x 1-3/8" deep [Ø8 x 35] if using

wall anchors (not supplied). Install anchors flush with wall face, or install other fastening

system suitable for wall conditions (not supplied). Attach dryer to wall. For wood wall/studs, use 1/4"

dia. (M6) screws at length that will ensure 1" [25] min. stud penetration. For masonry walls,

use expansion bolts or anchors (not supplied) for 1/4" dia (M6) screws to ensure penetration 1/4" [6]

deeper than anchor. Shim if necessary to ensure base plate is flat against wall.

6. Connect supply and ground wires to terminal block where indicated or connect supply wires to

terminal block where indicated and connect ground wire to base plate with ground screw.

Connections:

. Connect the live wire (colored Brown, Red or Black) to the terminal block marked "L".A

. Connect the neutral wire (colored Black, Blue, White or Grey) or connect the second live wireB

(colored Red or Orange) to the terminal block marked "N".

. Connect the ground wire to the terminal block marked " " or to the green screw marked " ".C

Bare grounding (earth) wires should be sleeved with green and yellow or green tubing.

Colors of live and neutral wires depend on voltage of supply service and requirements of Building

and Electrical Code having jurisdiction.

7. Replace cover and reinstall screws retained in Step 3 above. Do not over-tighten screws.

Installation Kit Included (find in carton)

Service Tool Included (with installation kit)

Security hex driver 4 mm x 1 pc (5/32" pin-hex will work if tool is lost)

Please unpack the unit and check the quantity of the above tool and kit.

1. Self-Threading screws 1/4" x 1-1/2" [M6 x 38] x 4 pcs 3. Nylon bushing x 4 pcs

2. Metal Washer 3/8" I.D. x 7/8" O.D. x 1/16" thick [Ø10 x Ø22 x 1.6] x 4 pcs

4. Crimp-on terminal wire tip x 3 pcs

Operating Instructions and Parts Manual

Hand Dryer Surf ace-mounted -com p li ant hand dr yer ADA

NOTE: All Dim’s Inch [mm]

1705120000 Rev C 05 July 2018

Produkt Specifikationer

Mærke:	ASI
Kategori:	Ikke kategoriseret
Model:	TURBO-Pro 10-0196-1-41

Har du brug for hjælp?

Hvis du har brug for hjælp til ASI TURBO-Pro 10-0196-1-41 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret ASI Manualer

ASI Turbo-Swift 10-0192-1-93 Manual

20 Februar 2025

ASI TURBO-Pro 10-0196-1-41 Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

YA-MAN Cavispa 360 Manual

17 August 2025

YA-MAN Blow Dry + Scalp Massage Manual

17 August 2025

Kenmore PM2010 Manual

17 August 2025

LG LM-U550 Manual

17 August 2025

Mars Gaming MF-NCLX2 Manual

17 August 2025

LG LM-U1350 Manual

17 August 2025

Mars Gaming MS-PULSE Manual

17 August 2025

MSW -MBV125 Manual

17 August 2025

Blaupunkt BP-DR200 Manual

17 August 2025

Mars Gaming MPS5-B2 Manual

17 August 2025