Assault Fitness Bike Pro X Manual

Assault Fitness motionscykel Bike Pro X

Læs gratis den danske manual til Assault Fitness Bike Pro X (2 sider) i kategorien motionscykel. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Assault Fitness Bike Pro X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1489

913

1499

1490

1483

Part# 23-AS-1515

QUICK START GUIDE

AS SHIPPED

ASSEMBLY

Introduction

• The ASSAULTBIKE PRO X requires only minor assembly. All tools required to complete the initial setup and assembly have

been included.

• Remove the unit and all parts from the carton and packaging. Conrm all parts shown in the section above titled “As Shipped”

are included before attempting assembly of the ASSAULTBIKE PRO X.

Assembly Step One:

Front & Rear Stabilizer Installation

• Align the front stabilizer (1483) with the receiver on the main frame, and install the two screws, lock washers and at

washers (1506, 1427 & 1426) with the supplied 5mm hex wrench.

• Align the rear stabilizer (1489) with the receiver on the main frame, and install the two screws, lock washers and at

washers (1506, 1427 & 1426) with the supplied 5mm hex wrench.

Assembly Step Two:

Console and Console Mast

• Inspect the console cable (1499) for damage before connecting it to the bottom side of the cable attached to the console mast

(913).

• Install the button head screws, lock washers, and at washers (1506, 1427 & 1426) through the console mast base (1498) and into

the main frame with the supplied 5mm hex wrench.

*If you are installing the optional water bottle & phone holder, please follow the provided instruction guide within the

user manual packet. If you are not installing the optional water bottle & phone holder, continue with the steps below.

• Plug the console wire (1499) into the pigtail wire that extends from the hole in the back side of the console (314) and carefully tuck

the excess wire into console mast (913). Do not pinch the cable.

• Insert the four screws (318) through the console mast (913) and into the back of the

console (314).

Assembly Step Three:

Handlebars

• Place the right handlebar assembly (1497) on the oor extending forward and away from the right linkage arm (907). Remove

the spring washers (1518 & 1519) and lock nut (1508) from the hardware/tool kit package.

• Slide the right linkage arm (912) onto the Lower Pivot Pin and install the smaller spring washer (1519) and locknut (1508) with

the provided 13mm wrench.

• Slide the larger spring washer (1518) onto the right handlebar (1497). Raise the right handlebar (1497) into a vertical position and

align the inside of the Upper Pivot Pin with the threaded mount on the main frame.

Thread the pivot into the frame by hand, then tighten rmly with the supplied

19mm/22mm combo wrench.

• Repeat the steps above for the left side assembly.

1489

1506

1427

1426

1483

1507

1425

318

314

913

1499

1506

1427

1426

1506

1427

1426

Assembly Step Four:

Seat, Pedals, & Leveling the Unit Assembly

• Loosen the seat clamp assembly that is pre-installed onto the rails of the seat (1502) and slip the assembly onto the knurled

portion of the seat slide (1470). Ensure the seat is level with the ground and x both nuts rmly and evenly.

• Install the at washer (1507) and hex screw (1425) into the end of the seat post assembly from the hardware/tool kit.

• The left pedal (1501) axle threads are reversed, meaning the axle tightens in the opposite direction from most screws or bolts

for installation. Engage the rst few threads of the left pedal axle into the left crank by hand with a counterclockwise rotation,

then tighten rmly with the 19mm/22mm combo wrench.

• Repeat this process for the right pedal (1502). NOTE: The right pedal axle will be rotated clockwise to install.

• Ensure the unit is level and does not rock by adjusting the leveling feet (1484). There are two feet on the front stabilizer and two on

the rear stabilizer. As a starting point, loosen each foot by threading the assembly downward/clockwise, and then thread the

locknuts downward (clockwise) against the foot base. Check the unit for stability and make any adjustments as necessary. Once

stable, lock the leveling feet (1484) in place by tightening the jam nut upward/counterclockwise, against the underside of the

stabilizer to lock the current position of each foot.

314

1503

1504

1497

1490

907

1508

912

1502

1470

1502

1501

1484

1519

1518

1506

Produkt Specifikationer

Mærke:	Assault Fitness
Kategori:	motionscykel
Model:	Bike Pro X

Har du brug for hjælp?

Hvis du har brug for hjælp til Assault Fitness Bike Pro X stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

motionscykel Assault Fitness Manualer

Assault Fitness Bike Pro X Manual

31 August 2024

motionscykel Manualer

Nyeste motionscykel Manualer

Toorx WBX-65 Manual

9 April 2025

Toorx BRX 300 Ergo Manual

9 April 2025

Toorx ERX-75 Manual

28 Marts 2025

Monark 894 E Manual

7 Februar 2025

Monark 827 E Manual

7 Februar 2025

LifeSpan TR1200B Manual

30 Januar 2025

Maxxus Multipresse 8.1 Manual

17 Januar 2025

Maxxus Multipresse 9.1 Manual

17 Januar 2025

Schwinn 470i Manual

12 Januar 2025

Schwinn AD2 Manual

12 Januar 2025