Atdec TH-3060-LPF Manual

Atdec Ikke kategoriseret TH-3060-LPF

Læs gratis den danske manual til Atdec TH-3060-LPF (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Atdec TH-3060-LPF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Nylon Anchor (x2)

Dry Wall anchor (x4)

M5/6/8 Washer

(x4 each)

M5x30/16mm (x4 each)

M6x30/16mm (x4 each)

M8x30/16mm (x4 each)

Display Mounting

Screws

M4/5 Spacer (x4)

M6/8 Spacer (x4)

Wall Plate

10mm(

8") Hole

Dry Wall Anchor

Dry Wall Anchor Screw

Note:

Each Dry Wall anchor should be at a

maximum distance from the next anchor point.

This is the recommended mounting pattern for

Dry Wall Anchors.

Coach Screw

Wall Plate

10mm(

8") Hole

Nylon Anchor

6mm(

4") Hole

Timber Stud

Wall Plate

Coach Screw

Note:

Use a stud finder to accurately locate

the centre of the stud. Ensure that all two

screws fix securely into the stud.

Hardware

Coach Screw (x2)

Components Checklist

Wall Plate

Display Bracket (x2)

IMPORTANT INFORMATION

! IMPORTANT - Install 3060 Wall Mount as per Installation Instructions.

! This product supports a maximum load of 65kg (143.3lbs).

! This product supports displays with mounting hole configurations from 100mm (4”) to 500mm (19½”) high,

and from 200mm (8”) to 810mm (32”) wide.

! The manufacturer does not accept responsibility for incorrect installation.

! Before installing this product, please check the display ventilation requirements with your

LED/LCD manufacturer.

Step 1. Check Components

Step 2. Mounting the Wall Plate

10mm ( drill bit



Spirit Level



Tools Required:

Power Drill



6mm

(

drill bit



Phillips Head screwdriver 

10mm

(

masonry drill bit

Large Flat Head Screw Driver

13mm

(

Socket Wrench or Shifter



Dry Wall

Tip: Use a spirit level to ensure wall plate is horizontal.

Masonry Wall

Timber Stud

OR OR

Check you have received all parts against the component checklist and Hardware above.

Installation Instructions

Hook Plate

Wall Plate

Note:

To access cable ports,

fold out screen tilt supports.

screen tilt support

Cut Release Ties so that they cannot

be seen from front of screen.

Spacer

(optional, used only for

recessed mounting holes)

Mounting Screw

Bracket

Washer

Back of Display

TOP

Hook Plate

Tip: If Hook Plates obstruct mounting

holes, remove and reposition

(as shown below.)

Hook Plate Screw

Use a large flat blade screwdriver

to remove/replace the two Hook

Plate screws.

Step 3. Attaching Brackets to Display

No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 14.10.10 ©

With the Brackets attached to the Display,

lower the Hook Plates onto the Wall plate.

Listen for "CLICK" to ensure the catch has

engaged.

Slide Display to desired position.

Step 4. Attaching/Detaching Display to Wall Plate (2 people required)

Step 5. Cable Management

Installation Complete

Detaching Display from Wall Plate:

To detach Display from wall plate, pull and

hold Release Ties to disengage locking

mechanism. Then lift the Display to unhook

from the wall plate.

Fold Tilt Supports back

once all

cables have been installed.

Power Cable

Release Tie

Note: Ensure that both

Release Ties are closest

to the outside edge of

the Display.

Release Tie

Produkt Specifikationer

Mærke:	Atdec
Kategori:	Ikke kategoriseret
Model:	TH-3060-LPF
Produktfarve:	Sort
Panel montering grænseflade:	200 x 100,200 x 200,300 x 300,400 x 400,600 x 400,800 x 400,300 x 200,400 x 300 mm
Monteringstype:	Væg
Skærmstørrelse kompatibilitet:	- "
Maksimal vægtkapacitet:	65 kg
Montering interface kompatibilitet (min.):	200 x 100 mm
Montering interface kompatibilitet (maks.):	400 x 300 mm