ATen PE0110SA Manual

ATen Strømskinne PE0110SA

Læs gratis den danske manual til ATen PE0110SA (2 sider) i kategorien Strømskinne. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om ATen PE0110SA, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CRack Mounting

other trademarks are the property of their respective owners.

This product is RoHS compliant.

Printing Date: 03/2019

Basic 1U PDU with surge protection

Quick Start Guide

PE0107S/PE0110S/PE0207S/

PE0209S/PE0210S

PE0107S/PE0110S/PE0207S/PE0209S/PE0210S with surge protection Quick Start Guide www.aten.com

ATEN NRGence™

AHardware Review

1 2 3 46 6 7

Rack Mounting

The Basic PDU can be installed in a 1U conﬁ guration on the side of a rack.

To rack mount the device, stabilize the device on the rack and tighten

screws onto the rack mount ears.

Hardware Review

1 Power Inlet

2 Circuit Breaker

3 Surge Protection

4 Surge Protection Indicator

5 Power Outlets

6 Rack Mount Ears

7 Grounding

Support and Documentation Notice

All information, documentation, ﬁ rmware,

software utilities, and speciﬁ cations

contained in this package are subject to

change without prior notiﬁ cation by

the manufacturer.

To reduce the environmental impact of our

products, ATEN documentation and software

can be found online at

http://www.aten.com/download/

Technical Support

www.aten.com/support

이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는

사용자는 이 점을 주의하시기 바라며, 가정외의 지역에

서 사용하는 것을 목적으로 합니다.

Scan for

more information

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT:

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

FCC Caution: Any changes or modiﬁ cations not expressly approved by

the party responsible for compliance could void the user's authority to

operate this equipment.

Warning: Operation of this equipment in a residential environment

could cause radio interference.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Package Contents

1 Power Distribution Unit

1 Power Cord

1 User Instructions

pe0110sa is the example used here. Please conﬁ rm the models corresponding to the given

pictures (models and pictures are not directly related).

BHardware Installation

Note: For safety reasons the equipment should be installed near the wall socket outlet and

the disconnected device (appliance coupler on detachable power supply cord or plug

on non-detachable power supply cord) should be readily accessible

Basic PDU

Rack

Hardware Installation

Refer to the installation diagram (the numbers in the diagram correspond to

the numbered steps), and do the following:

1Connect the Basic PDU's power cord to an AC power source.

2For each device you want to connect, connect its power cable between

the device's AC socket (where applicable) and any available outlet on the

Basic PDU.

Note: We strongly advise that you do not plug the Basic PDU into a multi

socket extension cord, since it may not receive enough amperage to

operate correctly. Once you have ﬁ nished

Surge Protection Indicator

The Surge Protection Indicator is as shown in the Hardware Review.

It should normally be lit when the unit is powered.

If the indicator is not lit when the unit is powered, please power down the

unit and any connected device safely. Return the unit to the dealer closest to

your location for further assistance.

Produkt Specifikationer

Mærke:	ATen
Kategori:	Strømskinne
Model:	PE0110SA

Har du brug for hjælp?

Hvis du har brug for hjælp til ATen PE0110SA stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Strømskinne ATen Manualer

21 August 2024

20 August 2024

19 August 2024

19 August 2024

19 August 2024

19 August 2024

19 August 2024

18 August 2024

18 August 2024

17 August 2024

Strømskinne Manualer

Nyeste Strømskinne Manualer

Philips SPN7080BA Manual

10 Marts 2025

Philips SPN5085B Manual

9 Marts 2025

Qian QEI-1000-01 Manual

27 Februar 2025

Act AC2425 Manual

21 Februar 2025

Act AC2415 Manual

20 Februar 2025

Act AC2420 Manual

20 Februar 2025

Sven SF-08E-16 Manual

31 December 2025

Brennenstuhl Estilo Manual

29 December 2024

Vivanco EPLS 6ALU Manual

7 December 2024

Vivanco EPLS 4USB_ALU Manual

7 December 2024