Audio-Technica AE6100 Manual

Audio-Technica Mikrofon AE6100

Læs gratis den danske manual til Audio-Technica AE6100 (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Audio-Technica AE6100, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

User Manual

Hypercardioid Dynamic Handheld Microphone AE6100

■Features

■Notes on use

■Connection procedure

Outp n sut termi al

PIN1 (ground)

PIN3

(cold)

PIN2 (hot)

■Speciﬁcations

Dynamic

Hypercardioid

60 - 15,000 Hz

-55 dB (1.7 mV) re 1V at 1 Pa

250 ohms

310 g

177.0 mm long, 48.0 mm head diameter,

33.0 mm to 22.0 mm tapered body diameter

Integral 3-pin XLRM-type

AT8470 Quiet-Flex stand clamp for 5/8"-27 threaded stands;

5/8"-27 to 3/8"-16 threaded adapter;

soft protective pouch

• 1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL

* Typical, A-weighted, using Audio Precision System One.

■P r atternola p

■Fr r o eequency esp ns

180°

150°

120°

30°

0°

330°

300°

270°

240°

210°

Audio-Technica Corporation

2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan

Global Support Contact: www.at-globalsupport.com

14-DEC--2020 Form No.ATGC-L0391-20

LEGEND

0°, 50cm

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

200 Hz

1 kHz

5 kHz

8 kHz

Thank you for purchasing this product. Before using the product, read through the user manual to

ensure that you will use the product correctly.

Please keep this manual for future reference.

Output from the microphone’s XLRM-type connector is low impedance (Lo-Z) balanced. The

signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive

acoustic pressure produces positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must be wired consistently: Pin

1-to-Pin 1, etc. For a high-impedance (Hi-Z) mic input, connect a Lo-Z balanced cable to a Hi-Z

matching transformer (A-T CP8201 or equal) at the equipment input.

When using the AE6100 in settings with a stage monitor speaker, the speaker should be located

135° oﬀ axis (45° oﬀ the rear of the microphone). This placement, in conjunction with the

microphone’s uniform hypercardioid pickup pattern, will virtually eliminate the possibility of

undesired audio feedback.

The high sensitivity of the AE6100 assures useful output and an excellent match to most input

sources. In some cases, however, an attenuator such as the Audio-Technica AT8202 may be

required between the microphone and preampliﬁer to avoid overloading sensitive input stages.

Take care to keep foreign particles from entering the windscreen. An accumulation of iron or

steel ﬁlings on the diaphragm, and/or foreign material in the windscreen’s mesh surface, can

degrade performance.

Connect e as a microphone input the output terminals of the microphone to a d vice that h

(balanced input). The output connector is an XLRM-type with polarity as shown in the ﬁgure

below.

For product improvement, the product is sublect to modiﬁcation without notice.

• Dynamic element gives pristine natural sound quality

• Tailored for an outstanding on-axis response

• Hardened steel body and grille for rugged durability

• High output, fast transients and clean articulation

• Multi-stage grille for reduced plosives and sibilance

• Superior anti-shock engineering for low handling noise

• Ergonomic design for easy handling

• Quiet-Flex stand clamp included for silent, ﬂexible mic positioning

■Safety precaution

■Cautions for the product

Although this product was designed to be used safely, failing to use it correctly may result in an

accident. To ensure safety, observe all warnings and cautions while using the product.

• Do not subject the product to strong impact to avoid malfunction.

• Do not disassemble, modify or attempt to repair the product.

• Do not handle the product with wet hands to avoid electric shock or injury.

• Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty

place.

Element

Polar pattern

Frequency response

Open circuit sensitivity

Impedance

Weight

Dimensions

Output connector

Accessories furnished

60°

90°

Response in dB

Frequency in Hertz

-10

-20

-30

50010050 200 10k5k1k 2k 20k

10 dB

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	AE6100

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica AE6100 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Audio-Technica Manualer

Audio-Technica ATW-CHG3AAD Manual

15 Oktober 2025

Audio-Technica ATW-2129CI Manual

29 August 2025

Audio-Technica ATM350UcH Manual

2 August 2025

Audio-Technica BP899LcH Manual

2 August 2025

Audio-Technica ATM350GL Manual

2 August 2025

Audio-Technica System 10 Stompbox ATW-1501 Manual

2 August 2025

Audio-Technica BP892c Manual

2 August 2025

Audio-Technica AT882TL Manual

2 August 2025

Audio-Technica ATM350SL Manual

2 August 2025

Audio-Technica System 20 PRO Manual

17 Juli 2025

Mikrofon Manualer

Nyeste Mikrofon Manualer

Saramonic Blink500 B3 Manual

3 November 2025

SGPRO D-332 Manual

2 November 2025

Maono Wave T1 Mini Manual

2 November 2025

Singing Machine Carpool Karaoke The Mic 2.0 Manual

2 November 2025

BONAOK Q37 Manual

2 November 2025

Phenyx Pro PTV-2000A Manual

2 November 2025

Saramonic Blink500T4 Manual

2 November 2025

Logitech Bluebird SL Manual

2 November 2025

Nady Encore I Manual

2 November 2025

FULAIM X5M Manual

2 November 2025