Audio-Technica AT4041 Manual

Audio-Technica Mikrofon AT4041

Læs gratis den danske manual til Audio-Technica AT4041 (1 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 120 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 60.5 anmeldelser. Har du et spørgsmål om Audio-Technica AT4041, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

• Smooth, extended frequency response with a slight rise occurring

in the high-frequency region

• Low-mass diaphragm improves transient response, increases

response bandwidth and reduces handling and mechanical noise

transfer

• Transformerless circuitry virtually eliminates low-frequency

distortion and provides superior correlation of high-speed

transients

• Rugged turned-brass microphone housing for enduring

dependability

• State-of-the-art design and manufacturing techniques ensure

compliance with A-T’s stringent consistency and reliability

standards

The AT4041 is intended for use in professional applications where

remote power is available. It requires 48V DC phantom power,

which may be provided by a mixer or console, or by a

separate, in-line source such as the Audio-Technica AT8801 single-

channel and CP8506 four-channel phantom power supplies.

Output from the microphone’s XLRM-type connector is low

impedance (Lo-Z) balanced. The signal appears across Pins 2 and

3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” –

positive acoustic pressure produces positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must be

wired consistently: Pin 1-to-Pin 1, etc.

An integral 80 Hz high-pass lter provides easy switching from a at

frequency response to a low-end roll-off. The high-pass position

reduces the microphone’s sensitivity to popping in close vocal use.

It also reduces the pickup of low-frequency ambient noise (such

as traffic, air-handling systems, etc.), room reverberation and

mechanically coupled vibrations.

Avoid leaving the microphone in the open sun or in areas where

temperatures exceed 110° F (43° C) for extended periods.

Extremely high humidity should also be avoided.

One-Year Limited Warranty

Audio-Technica brand products purchased in the U.S.A. are warranted for one year from date

of purchase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and

workmanship. In event of such defect, product will be repaired promptly without charge or, at

our option, replaced with a new product of equal or superior value if delivered to A.T.U.S. or

an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase

date. Prior approval from A.T.U.S. is required for return. This warranty excludes defects

due to normal wear, abuse, shipping damage, or failure to use product in accordance with

instructions. This warranty is void in the event of unauthorized repair or modification, or

removal or defacing of the product labeling.

For return approval and shipping information, contact the Service Department,

Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.

Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for

any consequential, incidental, or special damages; any warranty of merchantability or

fitness for particular purpose expires when this warranty expires.

This warranty gives you specific legal rights, and you may have other rights which vary from

state to state.

Outside the U.S.A., please contact your local dealer for warranty details.

AT4041 SPECIFICATIONS†

ELEMENT Fixed-charge back plate

permanently polarized

condenser

POLAR PATTERN Cardioid

FREQUENCY RESPONSE 20-20,000 Hz

LOW FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave

OPEN CIRCUIT SENSITIVITY –36 dB (15.8 mV) re 1V at 1 Pa*

IMPEDANCE 100 ohms

MAXIMUM INPUT SOUND LEVEL 145 dB SPL, 1 kHz at 1% T.H.D.

DYNAMIC RANGE (typical) 121 dB, 1 kHz at Max SPL

SIGNAL-TO-NOISE RATIO170 dB, 1 kHz at 1 Pa*

PHANTOM POWER 48V DC, 3.2 mA typical

REQUIREMENTS

SWITCH Flat, roll-o

WEIGHT (less accessories) 4.2 oz (120 g)

DIMENSIONS 6.28" (159.5 mm) long, 0.83"

(21.0 mm) body diameter

OUTPUT CONNECTOR Integral 3-pin XLRM-type

ACCESSORIES FURNISHED AT8405 stand clamp for 5

/8"-27

threaded stands; AT8159

windscreen; protective carrying

case

†In the interest of standards development, A.T.U.S. oers full details on its test

methods to other industry professionals on request.

*1 Pascal = 10 dynes /cm2= 10 microbars = 94 dB SPL

1Typical, A-weighted, using Audio Precision System One.

Specications are subject to change without notice.

Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224

Audio-Technica Limited, Old Lane, Leeds LS11 8AG England

www.audio-technica.com

AT4041

CARDIOID CONDENSER MICROPHONE

LEGEND

Frequency in Hertz

12" or more on axis

Roll-o

200100 500 2k1k 5k

Frequency Response

Response in dB

20k10k

10 dB

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

200 Hz

8 kHz

5 kHz

1 kHz

Polar Pattern

210

240

270

300

330

150

180

120

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	AT4041
Type:	Scene/optræden mikrofon
Produktfarve:	Sort
Husmateriale:	Messing
Forbindelsesteknologi:	Ledningsført
Enhedsgrænseflade:	mini XLR (3-pin)
Bæretaske:	Ja
Mikrofonindgangsimpedans:	100 ohm (Ω)
Mikrofon frekvens:	20 - 20000 Hz
Mikrofonretningstype:	Kardioid
Mikrofon sensitivitet:	-36 dB
Mikrofon vægt:	120 g
klirfaktor (THD):	1 %
Anbefalet køn:	Ethvert køn
Antal produkter inkluderet:	1 stk
Svingspole type:	Forpolariseret kondensator
Mikrofon dimensioner (DxH):	21 x 159.5 mm
Mikrofon, signal-til-støjforhold:	70 dB
Mikrofonholder:	Ja
Mikrofon dynamikområde:	121 dB
Maksimalt lydtrykniveau (1kHz):	145 dB
Lavskåret filter:	80 Hz