Audio-Technica ATM650 Manual

Audio-Technica Mikrofon ATM650

Læs gratis den danske manual til Audio-Technica ATM650 (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Audio-Technica ATM650, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

HYPERCARDIOID DYNAMIC INSTRUMENT MICROPHONE

- Tailored response for musical instrument pickup-guitar cabinets,

snare and other percussion.

- Hypercardioid polar pattern reduces pickup of sounds from the

sides and rear, improving isolation of desired sound source.

- Durable performance for professional applications.

- Special dual-wall oating construction reduces handling noise and

assures consistent performance from mic to mic.

- Hi-ENERGY® neodymium magnet for improved output and transient

response.

- Multi-stage at grille design is engineered to enable easy placement

as close as possible to sound source.

- Corrosion-resistant contacts from gold-plated XLRM-type connector.

- Rugged, all-metal design and construction for years of trouble-free

use.

Output from the microphone’s XLRM-type connector is low imped-

ance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin

1 is ground (shield). Output phase is “Pin 2 hot” - positive acoustic

pressure produces positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must be

wired consistently: Pin 1-to-Pin 1, etc. For a high-impedance (Hi-Z)

mic input, connect a Lo-Z balanced cable to a Hi-Z matching trans-

former (A-T CP8201 or equal) at the equipment input.

When using the ATM650 in settings with a stage monitor speaker,

the speaker should be located 135° off axis (45° off rear of the micro-

phone). This placement, in conjunction with the microphone’s uniform

hypercardioid pickup pattern, will virtually eliminate the possibility of

undesired audio feedback.

Take care to keep foreign particles from entering the windscreen. An

accumulation of iron or steel lings on the diaphragm, and/or foreign

material in the windscreen’s mesh surface, can degrade perfor-

mance.

Note: Remove the rubber sleeve at the base of the microphone han-

dle to use the AT8471 isolation stand clamp (not included) for more

secure, permanent installation.

FORM No. ATGC-L0027-06-E

Machida • Toky o • Japan

10 dB

20k10k5k2k1k50020010050

8 kHz

200 Hz

1 kHz

5 kHz

0°

330°

300°

270°

240°

210°

180°

150°

120°

90°

60°

30°

Polar Pattern

Frequency Response

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

Frequency in Hertz

LEGEND 12” or more on axis

Response in dB

SPECIFICATIONS

ELEMENT Dynamic

POLAR PATTERN Hypercardioid

FREQUENCY RESPONSE 80-17,000 Hz

OPEN CIRCUIT SENSITIVITY -56 dB (1.5 mV) re 1V at 1 Pa

IMPEDANCE 300 ohms

WEIGHT (less cable and accessories) 279 g

DIMENSIONS 164.2 mm - long,

38.8 mm - diameter

OUTPUT CONNECTOR Integral 3-pin XLRM-type

ACCESSORIES FURNISHED AT8470 Quiet-Flex™ stand clamp for

⅝”-27 threaded stand;

⅝”-27 to ⅜”-16 threaded adapter;

Soft protective pouch

10 dB

20k10k5k2k1k50020010050

8 kHz

200 Hz

1 kHz

5 kHz

0°

330°

300°

270°

240°

210°

180°

150°

120°

90°

60°

30°

指向特性

频率特性

声压曲线 1刻度5 dB

频率

频率 (赫兹 )

电平平直

响应电平 (dB)

FORM No. ATGC-L0027-06-C

Machida • Tokyo • Japan

超心形指向性动圈式乐器话筒

- 专为结他、小鼓及其他敲击乐器等作收音而开发。

- 超心形指向性设计，减低旁边及后方的噪声干扰，提高收音

目标的隔离度。

- 专业应用性的耐用表现。

- 使用浮动式双筒抗震垫设计，减至最少的手持摩擦噪声，并

可维整体重量平衡。

- Hi-ENERGY® 高能量钕硼磁铁，提供更大输出及音质透明度。

- 多层平面式音头保护网结构，能加强收录爆破声时的保护，

又不会影响高音的收音质量。

- 抗腐蚀的镀金XLRM卡农输出头。

- 全金属结构，坚固、耐用、可长期使用。

话筒的卡农输出端为低阻抗平衡输出，话筒音频信号最终XLRM

以卡农公头的2号及3号针脚输出，而1号针脚则为地线(屏蔽)连

接。输出相位将以正相位电平设于 2号针脚上。

为避免出现相位相互抵消而失真的情况，所有话筒连接时，

接线必需以 1-1，2-2，3-3型式把针脚连接。如连接高阻抗的话

筒输入，请配套阻抗匹配变压器AT8201。

当ATM650话筒及现场监听音箱同时使用时，需要把音箱放置于

话筒的 135°后方(正后方的45°位置)。在这位置上，由于话筒的

超心形指向性设计，可减低出现反馈回声的情况。

小心不要把金属碎或铁屑掉进防风罩内，铁屑会吸进收音头磁铁

中，或贴在防风罩内，将会影响及减低收音效果。

备注：可除掉话筒底部的橡胶套筒，而换上AT8471防震话筒套

(选配件)，可作为更稳固及永久安装使用。

技术指标

收音头动圈式

指向特性超心形指向性

频率响应 80-17,000 Hz

开通灵敏度 -56 dB (1.5 mV) 以 1V 于 1 Pa

输出阻抗 300 欧姆

重量(不带连线与配件) 279 克

外形尺寸 164.2 mm - 长度,

38.8 mm - 直径

输出连接器内置 XLRM-3针卡农公头

附属品 AT8470 Quiet-Flex™ - ⅝”-27接头

话筒夹，

⅝”-27至⅜”-16转接头，保護袋。

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	ATM650

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica ATM650 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Audio-Technica Manualer

Audio-Technica ATM355 Manual

1 Marts 2025

Audio-Technica BP892xCW Manual

13 Januar 2025

Audio-Technica ATGM2 Manual

6 December 2024

Audio-Technica Creator Pack Manual

6 December 2024

Audio-Technica AT2040 Manual

6 December 2024

Audio-Technica AE2500 Manual

6 December 2024

Audio-Technica AT881TH/RC Manual

6 December 2024

Audio-Technica AT882TH Manual

6 December 2024

Audio-Technica AT882TH/D3RC5 Manual

6 December 2024

Audio-Technica AT4033a Manual

6 December 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Kogan KAGMICBOMLA Manual

15 Juni 2025

Omnitronic UHF-601 Manual

14 Juni 2025

Omnitronic UHF-604 Manual

14 Juni 2025

Omnitronic UHF-602 Manual

14 Juni 2025

Neewer VM11 Manual

14 Juni 2025

Neewer KM23 Manual

13 Juni 2025

AmpliVox S1695 Manual

13 Juni 2025

Comica BooMax Manual

12 Juni 2025

DNA UWM 1 Manual

9 Juni 2025

DNA PSV 2 Manual

9 Juni 2025