Audio-Technica ATND971a Manual

Audio-Technica Mikrofon ATND971a

Læs gratis den danske manual til Audio-Technica ATND971a (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Audio-Technica ATND971a, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

ATND971

Cardioid Condenser Boundary Microphone with Dante™ Network Output

Features

Description

The ATND971 is a Dante-enabled, wide-range condenser microphone with a cardioid polar pattern. It is designed

for surface-mount applications such as high-quality sound reinforcement, conferencing, distance learning and other

demanding sound pickup applications.

The microphone features a touch-sensitive capacitive-type user switch with integral red/green LED status indicator.

In Local mode the user switch mutes and unmutes the microphone. It can be set to toggle between live and muted

audio (toggle on/off), to permit live audio only while the switch is pressed (press to talk), or to mute the audio

while the switch is pressed (press to mute). In Remote mode the user switch can be used to trigger functions on

compatible Dante-enabled devices, such as a video camera’s pan/tilt or a room’s lighting preset. While in Remote

mode the microphone’s audio output is controlled remotely.

The audio output of the ATND971 can be routed using Audinate’s Dante Controller, which is available for download

at the Audinate website (www.audinate.com). The site also provides Dante routing and software instructions.

The microphone is equipped with UniGuard® RFI-shielding technology, which offers outstanding rejection of radio

frequency interference (RFI).

The microphone’s cardioid polar pattern provides a 120° angle of acceptance (cardioid in hemisphere above

mounting surface). Additional interchangeable elements with omnidirectional (360°) and hypercardioid (100°) pickup

patterns are available.

Operation and Maintenance

The ATND971 is powered by network PoE. The electronics in the microphone take up

to 30 seconds to stabilize after power is applied.

The microphone should be placed on a at, unobstructed mounting surface, with the

front of the microphone facing the sound source. The sound source should not be

below, or higher than 60° above, the plane of the mounting surface.

The microphone features a touch-sensitive user switch with integral red/green LED status indicator. The user switch

has four Local settings that can be chosen by pressing the button beneath “SWITCH FUNCTION” and “DEFAULT

MODE.” The default setting is TOGGLE ON/OFF. Press the button once to change setting to TOGGLE ON/OFF. In both

settings the user switch will toggle between mute and unmute – the only difference is the status of the audio when

the microphone is turned on. Press the button a second time to select MOM. ON (momentary on), wherein the audio

will be on only while the user switch is being pressed (press to talk). Press the button a third time to select MOM.

OFF (momentary off), wherein the audio will be muted while the user switch is being pressed. Press the button a

fourth time to cycle the setting back to the default. The “SWITCH FUNCTION” and “DEFAULT MODE” LEDs will

illuminate red or green to indicate the current setting.

Turn the low-cut UniSteep® lter on and off by pressing the button beneath “LOW CUT” on the bottom of the

microphone. The lter is off by default. The LED above “LOW CUT” illuminates red when the lter is off, green when

it is on.

There are three input gain levels that can be selected: +30 dB (for loudest voices), +40 dB and +50 dB (for softest

voices). To adjust the gain level, press the button beneath “GAIN” on the bottom of the microphone. Pressing the

button once changes the level from +30 dB to +40 dB, pressing it again changes the level to +50 dB and pressing a

third time returns the level to +30 dB. The LED above “GAIN” illuminates green for +30 dB, orange for +40 dB and

red for +50 dB.

To lock the Local settings, press and hold the button beneath “LOCK” on the bottom of the microphone. Press and

hold again to unlock settings. The LED above “LOCK” will illuminate red when locked and remain unlit when not

locked. If a setting button is pressed while the lock is on, the LOCK LED will blink.

All LEDs on the bottom of the microphone will turn off seven seconds after the last button is pressed. Pressing any

button will cause the LEDs to relight.

Specifications

Element Fixed-charge back plate,

permanently polarized condenser

Polar pattern Half-cardioid (cardioid in hemisphere

above mounting surface)

Frequency response 30-20,000 Hz

Low frequency roll-off 80 Hz, 18 dB/octave

Maximum input sound level 117 dB SPL, 1 kHz at 1% T.H.D.

Signal-to-noise radio 68 dB, 1 kHz at 1 Pa

Power requirements PoE IEEE802.3af standard

Power consumption 1.5W

Switches Local Mode:

Touch-sensitive capacitive type user switch function:

toggle (mute on power up), toggle (talk on power up),

momentary on, momentary off;

Low-cut lter: at, roll-off; Gain: +30 dB, +40 dB, +50 dB

Remote Mode:

Low-cut and Gain via third-party software*

Weight 393 g

Dimensions 110.0 mm (L), 89.5 mm (W), 35.8 mm (H)

Output connector RJ45

Dante network Physical level: standard Ethernet

Connector: single RJ45

Cable quality: Shielded CAT5 or CAT6 recommended

Transmission speed: 100 Mbps

Optional interchangeable elements UE-O omnidirectional (360°)

UE-H hypercardioid (100°)

Accessory furnished Soft protective pouch

frequency response: 30–20,000 Hz polar pattern

Frequency in Hertz

LEGEND

Response in dB

12" or more on axis SCALE IS 5 DECIBELS PER DIVISION

FORM No. ATGC-L0326-15-E

Machida • Tokyo • Japan

To return the microphone to its default Local settings, press the GAIN and LOW CUT buttons simultaneously.

The microphone can also be controlled remotely via third-party software.* When this software is used it will

override local control, causing the audio to remain on and the red/green LED status indicator, low-cut lter and input

gain level to be controlled remotely. In Remote mode the microphone’s user switch can be programmed to trigger

functions on compatible Dante-enabled devices. When in remote mode the Remote LED is illuminated.

Avoid leaving the microphone in the open sun or in areas where temperatures exceed 43° C for extended periods.

Extremely high humidity should also be avoided.

User Switch Settings and Functions in Local Mode

CONTROL

User Switch Mode SWITCH FUNCTION

LED Color

DEFAULT MODE

LED Color

Default Toggle

(mute on power up)

Green Red

1st Press Toggle

(talk on power up)

Green Green

2nd Press Press to Talk Red Red

3rd Press Press to Mute Red Green

Roll-off

110 mm

DANTE/PoE

89.5 mm

35.8 mm

network microphones

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	ATND971a

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica ATND971a stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Audio-Technica Manualer

Audio-Technica ATW-CHG3AAD Manual

15 Oktober 2025

Audio-Technica ATW-2129CI Manual

29 August 2025

Audio-Technica ATM350UcH Manual

2 August 2025

Audio-Technica BP899LcH Manual

2 August 2025

Audio-Technica ATM350GL Manual

2 August 2025

Audio-Technica System 10 Stompbox ATW-1501 Manual

2 August 2025

Audio-Technica BP892c Manual

2 August 2025

Audio-Technica AT882TL Manual

2 August 2025

Audio-Technica ATM350SL Manual

2 August 2025

Audio-Technica System 20 PRO Manual

17 Juli 2025

Mikrofon Manualer

Nyeste Mikrofon Manualer

SE Electronics V7 ENG Manual

15 December 2025

Eurosound PRO3 Manual

11 December 2025

Philips SmartMeeting PSE0540 Manual

8 December 2025

Galaxy Audio EVO-PE0P1 Manual

8 December 2025

Galaxy Audio EVO-PE0D4 Manual

8 December 2025

Philips SmartMeeting PSE0501 Manual

7 December 2025

Galaxy Audio AS-ANTM3 Manual

7 December 2025

Galaxy Audio EVO-PEED4 Manual

7 December 2025

TOA S4.10-RXA Manual

6 December 2025

Savage Mobile Vlogging Kit Manual

5 December 2025