Audio-Technica ES925C/FM5 Manual

Audio-Technica Mikrofon ES925C/FM5

Læs gratis den danske manual til Audio-Technica ES925C/FM5 (3 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Audio-Technica ES925C/FM5, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
1
ES925C6/FM5
ES925C12/FM5
ES925C15/FM5
ES925C18/FM5
ES925C21/FM5
ES925C24/FM5
User Manual
CARDIOID CONDENSER
MODULAR GOOSENECK MICROPHONE
WITH 5-PIN FLUSH-MOUNT POWER MODULE
■Introduction
Thank you for purchasing this product. Before using the product, read through
the user manual to ensure that you will use the product correctly. Please keep
this manual for future reference.
■Features
• Modular microphone system comprised of an ES Series capsule, gooseneck
assembly, and power module.
• RGB LEDs built into both the flush-mount power module and gooseneck
assembly indicate the on/off status of the microphone.
• Includes external control function for device control from the capacitive touch
switch.
• The capacitive touch switch can be set to any of three operating modes:
“touch-on/touch-off”, “touch-to-talk” and “touch-to-mute”.
■Safety precautions
Although this product was designed to be used safely, failing to use it correctly
may result in an accident. To ensure safety, observe all warnings and cautions
while using the product.
■Cautions for the product
• Do not subject the product to strong impact to avoid malfunction.
• Do not disassemble, modify or attempt to repair the product.
• Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a
hot, humid or dusty place.
■Notes on use
• Check the strength of the mounting area. Insufficient strength or poor
mounting will cause objects to fall or become damaged.
• The circuitry in the microphone takes about 30 seconds to stabilize after power
is supplied. You may hear some audio disturbance during startup.
• Install the microphone on a flat, unobstructed mounting surface.
• Depending on the surface finish of a table, the isolators may leave marks on
the table.
• Do not excessively bend the gooseneck assembly, rotate the ends of the
capsule, or pull on them. Doing so may cause disconnection or malfunction.
• The product is a modular system comprised of a microphone element,
gooseneck assembly and power module. Make sure the parts are firmly
attached before use.
• Do not remove the rubber O-ring on the power module connecting part at the
lower section of the gooseneck assembly.
• When attaching parts, remove the black cap on the capsule connecting part
of the gooseneck assembly. Do not remove the silicone part at the end of
the capsule connecting part.
Silicone part
Do not remove
2
■Assembly
• Insert the gooseneck assembly (c) while rotating it into the flush-mount power
module (d).
• Tighten until it does not rotate, and use the hex wrench (i) to tighten the set
screw (h) and set the gooseneck assembly in place.
• Connect the capsule (b) to the gooseneck assembly, and attach the windscreen (a).
* If the parts are not sufficiently tightened together, problems may occur such as
the LED colors of the gooseneck assembly and power module not matching or
sound is not output.
• Refer to the LED table to the right and set the LED color before attaching to
the mounting surface.
• If you are installing the flush-mount power module on a table without the isolators,
you must make a hole with a diameter of 20.5 mm in the mounting surface.
• If you are installing with the isolators, the hole must have a diameter of 23.5 mm.
Inserting the isolators between the mounting surface and power module allows
you to separate the flush-mount power module from the mounting surface.
• Attach the upper part isolator (e) to the mounting surface, and attach the flush-
mount power module (d). Attach the lower isolator (f) to the reverse side of the
mounting surface, and then tighten the nut (g).
a
b
c
d
e
f
g
hi
■Switch setting and functions
1
5
4
MIC
2
Contact
Closure
GND
1. Action 5. LED
status
4. LED color
3. Audio
status
2. Contact
closure
status
■LED color
1 2 3
OFF RED GREEN
YELLOW
4 5 6 7
BLUE
MAGENTA
CYAN WHITE
■Wiring
PIN1
(Ground)
PIN5
(LED control)
PIN4
(Contact closure)
PIN3
(Cold)
PIN2
(Hot)

Produkt Specifikationer

Mærke: Audio-Technica
Kategori: Mikrofon
Model: ES925C/FM5

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica ES925C/FM5 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Mikrofon Audio-Technica Manualer

Audio-Technica

Audio-Technica ATM355 Manual

1 Marts 2025
Audio-Technica

Audio-Technica BP892xCW Manual

13 Januar 2025
Audio-Technica

Audio-Technica ATGM2 Manual

6 December 2024
Audio-Technica

Audio-Technica Creator Pack Manual

6 December 2024
Audio-Technica

Audio-Technica AT2040 Manual

6 December 2024
Audio-Technica

Audio-Technica AE2500 Manual

6 December 2024
Audio-Technica

Audio-Technica AT881TH/RC Manual

6 December 2024
Audio-Technica

Audio-Technica AT882TH Manual

6 December 2024
Audio-Technica

Audio-Technica AT882TH/D3RC5 Manual

6 December 2024
Audio-Technica

Audio-Technica AT4033a Manual

6 December 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Kogan

Kogan KAGMICBOMLA Manual

15 Juni 2025
Omnitronic

Omnitronic UHF-601 Manual

14 Juni 2025
Omnitronic

Omnitronic UHF-604 Manual

14 Juni 2025
Omnitronic

Omnitronic UHF-602 Manual

14 Juni 2025
Neewer

Neewer VM11 Manual

14 Juni 2025
Neewer

Neewer KM23 Manual

13 Juni 2025
AmpliVox

AmpliVox S1695 Manual

13 Juni 2025
Comica

Comica BooMax Manual

12 Juni 2025
DNA

DNA UWM 1 Manual

9 Juni 2025
DNA

DNA PSV 2 Manual

9 Juni 2025