Audio-Technica ES925/FM3 Manual

Audio-Technica Mikrofon ES925/FM3

Læs gratis den danske manual til Audio-Technica ES925/FM3 (3 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Audio-Technica ES925/FM3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

ES925H6/FM3

ES925H12/FM3

ES925H15/FM3

ES925H18/FM3

ES925H21/FM3

ES925H24/FM3

User Manual

HYPERCARDIOID CONDENSER

MODULAR GOOSENECK MICROPHONE

WITH 3-PIN FLUSH-MOUNT POWER MODULE

■Introduction

Thank you for purchasing this product. Before using the product, read through

the user manual to ensure that you will use the product correctly. Please keep

this manual for future reference.

■Features

• Modular microphone system comprised of an ES Series capsule, gooseneck

assembly, and power module.

• RGB LEDs built into both the flush-mount power module and gooseneck

assembly indicate the on/off status of the microphone.

• Capacitive touch switch for microphone control.

• Three-pin output power module allows for inconspicuous tabletop installation.

■Safety precautions

Although this product was designed to be used safely, failing to use it correctly

may result in an accident. To ensure safety, observe all warnings and cautions

while using the product.

■Cautions for the product

• Do not subject the product to strong impact to avoid malfunction.

• Do not disassemble, modify or attempt to repair the product.

• Do not handle the product with wet hands to avoid electric shock or injury.

• Do not store the product under direct sunlight, near heating devices or in a

hot, humid or dusty place.

■Notes on use

• Check the strength of the mounting area. Insufficient strength or poor

mounting will cause objects to fall or become damaged.

• The circuitry in the microphone takes about 30 seconds to stabilize after power

is supplied. You may hear some audio disturbance during startup.

• Install the microphone on a flat, unobstructed mounting surface.

• Depending on the surface finish of a table, the isolators may leave marks on

the table.

• Do not excessively bend the gooseneck assembly, rotate the ends of the

capsule, or pull on them. Doing so may cause disconnection or malfunction.

• The product is a modular system comprised of a microphone element,

gooseneck assembly and power module. Make sure the parts are firmly

attached before use.

• Do not remove the rubber O-ring on the power module connecting part at the

lower section of the gooseneck assembly.

• When attaching parts, remove the black cap on the capsule connecting part

of the gooseneck assembly. Do not remove the silicone part at the end of

the capsule connecting part.

Silicone part

Do not remove

■Assembly

• Insert the gooseneck assembly (c) while rotating it into the flush-mount power

module (d).

• Tighten until it does not rotate, and use the hex wrench (i) to tighten the set

screw (h) and set the gooseneck assembly in place.

• Connect the capsule (b) to the gooseneck assembly, and attach the windscreen

(a).

* If the parts are not sufficiently tightened together, problems may occur such as

the LED colors of the gooseneck assembly and power module not matching or

sound is not output.

• Refer to the LED table to the right and set the LED color before attaching to

the mounting surface.

• If you are installing the flush-mount power module on a table without the

isolators, you must make a hole with a diameter of 20.5 mm in the mounting

surface.

• If you are installing with the isolators, the hole must have a diameter of 23.5

mm. Inserting the isolators between the mounting surface and power module

allows you to separate the flush-mount power module from the mounting

surface.

• Attach the upper part isolator (e) to the mounting surface, and attach the flush-

mount power module (d). Attach the lower isolator (f) to the reverse side of the

mounting surface, and then tighten the nut (g).

■Switch setting and functions

1. Action

2. Audio

status

3. LED color 4. LED status

■LED color

1 2 3

OFF RED GREEN

YELLOW

4 5 6 7

BLUE

MAGENTA

CYAN WHITE

■Wiring

1 2

PIN1

(Ground)

PIN2

(Hot)

PIN3

(Cold)

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	ES925/FM3

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica ES925/FM3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Audio-Technica Manualer

Audio-Technica ATM355 Manual

1 Marts 2025

Audio-Technica BP892xCW Manual

13 Januar 2025

Audio-Technica ATGM2 Manual

6 December 2024

Audio-Technica Creator Pack Manual

6 December 2024

Audio-Technica AT2040 Manual

6 December 2024

Audio-Technica AE2500 Manual

6 December 2024

Audio-Technica AT881TH/RC Manual

6 December 2024

Audio-Technica AT882TH Manual

6 December 2024

Audio-Technica AT882TH/D3RC5 Manual

6 December 2024

Audio-Technica AT4033a Manual

6 December 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Kogan KAGMICBOMLA Manual

15 Juni 2025

Omnitronic UHF-601 Manual

14 Juni 2025

Omnitronic UHF-604 Manual

14 Juni 2025

Omnitronic UHF-602 Manual

14 Juni 2025

Neewer VM11 Manual

14 Juni 2025

Neewer KM23 Manual

13 Juni 2025

AmpliVox S1695 Manual

13 Juni 2025

Comica BooMax Manual

12 Juni 2025

DNA UWM 1 Manual

9 Juni 2025

DNA PSV 2 Manual

9 Juni 2025