Audio-Technica MT838IIa Manual

Audio-Technica Mikrofon MT838IIa

Læs gratis den danske manual til Audio-Technica MT838IIa (2 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Audio-Technica MT838IIa, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SUBMINIATURE OMNIDIRECTIONAL CONDENSER CLIP-ON MICROPHONE

- Maximum intelligibility and clean, accurate reproduction for lecturers,

stage and television talent, and worship leaders.

- Low-prole design is ideal for applications requiring minimum visibility.

- Includes a wire clothing clip and a metal-frame pop lter.

- MT838IIa is switchable for low-frequency roll-off reduces sensitivity to

popping in close vocal use.

- MT838IIa can be operated on battery or phantom power.

- MT838IIcW is terminated for use with all Audio-Technica UniPak™

wireless systems.

The MT838IIa / MT838IIcW is worn on the clothing of performers

for excellent yet unobtrusive sound pickup. Its small size makes the

microphone ideal for use in applications where minimum visibility

is required. Clo se-up voice pickup i s crisp and cle an, and t he

omnidirectional polar pattern of the microphone assures nearly equal

sound pickup from every direction across a wide band frequencies.

The included clothing clip and metal-frame pop filter are removable.

When using the MT838IIa / MT838IIcW in extremely close situations, slip

the included metal-frame pop lter over the mic to reduce wind noise or

“poping”.

MT838IIa

Includes a power module AT8531 that requires 11V to 52V DC phantom

power, or a 1.5V AA battery for operation. A battery need not be in place

for phantom power operation.

An integral 80Hz high-pass filter provides easy switching from a flat

frequency response to a low-end roll-off. The roll-off position reduces

the pickup of low-frequency ambient noise (such as trafc, air-handling

systems, etc.), room reverberation and mechanically coupled vibrations.

Output from the power module’s XLRM-type connector is low impedance

(Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground

(shield). Output phase is “Pin 2 hot” - positive acoustic pressure produces

positive voltage at Pin 2. To avoid phase cancellation and poor sound, all

mic cables must be wired consistently: Pin 1-to-Pin 1, etc.

MT838IIcW

Less power module and includes clothing clip and metal-frame pop lter

only. 1.8 m cable terminated with locking 4-pin connector for Audio-

Technica UniPak™ body-pack wireless transmitters.

Avoid leaving the microphone i n the open sun or in areas where

temperatures exceed 40°C for extended periods. Extremely high humidity

should also be avoided.

FORM No. ATGC-L0074-07-E

Machida • Tokyo • Japan

SPECIFICATIONS

ELEMENT Fixed-change back plate permanently

polarized condenser

POLAR PATTERN Omnidirectional

FREQUENCY RESPONSE 20-18,000 Hz

OPEN CIRCUIT SENSITIVITY -62 dB (0.79 mV) re 1V at 1 Pa (capsule)

IMPEDANCE 1800 ohms (capsule)

OPERATING VOLTAGE 1.5 -10V DC (capsule)

LOW FREQUENCY ROLL-OFF 80 Hz, 12 dB/octave (MT838IIa)

PHANTOM POWER REQUIREMENTS 11-52V DC, 2 mA typical (MT838IIa)

BATTERY TYPE 1.5V AA (MT838IIa)

BATTERY CURRENT / LIFE 2.0 mA / 1200 hours (MT838IIa)

SWITCHES (MT838IIa)Flat, roll-off

WEIGHT (less cable and accessories)

MICROPHONE

POWER MODULE (AT8531)

7.7 g

81.2 g

DIMENSIONS

MICROPHONE

POWER MODULE (AT8531)

21.5 mm - long,

6.5 mm - diameter

83.0 mm - H x 63.0 mm - W x

22.0 mm - D

OUTPUT CONNECTOR

MT838IIa (AT8531)

MT838IIcW

Integral 3-pin XLRM-type

locking 4-pin connector for UniPak™

CABLE 1.8 m long (permanently attached to

microphone), 2 mm diameter

ACCESSORIES FURNISHED Wire clothing clip;

metal-frame pop lter;

protective pouch.

AT8531 power module (MT838IIa)

10 dB

20k10k5k2k1k50020010050

8 kHz

200 Hz

1 kHz

5 kHz

0°

330°

300°

270°

240°

210°

180°

150°

120°

90°

60°

30°

Polar Pattern

Frequency Response

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

Frequency in Hertz

LEGEND 12” or more on axis

Response in dB

Roll-off (MT838IIa)

same as 1 kHz

Produkt Specifikationer

Mærke:	Audio-Technica
Kategori:	Mikrofon
Model:	MT838IIa

Har du brug for hjælp?

Hvis du har brug for hjælp til Audio-Technica MT838IIa stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Audio-Technica Manualer

Audio-Technica ATW-CHG3AAD Manual

15 Oktober 2025

Audio-Technica ATW-2129CI Manual

29 August 2025

Audio-Technica ATM350UcH Manual

2 August 2025

Audio-Technica BP899LcH Manual

2 August 2025

Audio-Technica ATM350GL Manual

2 August 2025

Audio-Technica System 10 Stompbox ATW-1501 Manual

2 August 2025

Audio-Technica BP892c Manual

2 August 2025

Audio-Technica AT882TL Manual

2 August 2025

Audio-Technica ATM350SL Manual

2 August 2025

Audio-Technica System 20 PRO Manual

17 Juli 2025

Mikrofon Manualer

Nyeste Mikrofon Manualer

BONAOK Q37 Manual

2 November 2025

Phenyx Pro PTV-2000A Manual

2 November 2025

Saramonic Blink500T4 Manual

2 November 2025

Logitech Bluebird SL Manual

2 November 2025

2 November 2025

2 November 2025

2 November 2025

1 November 2025

Icon Space 103 Manual

31 Oktober 2025

Fifine AmpliGame AM8PROT Manual

30 Oktober 2025