Ausclimate C545 Manual

Ausclimate Luftrenser C545

Læs gratis den danske manual til Ausclimate C545 (2 sider) i kategorien Luftrenser. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Ausclimate C545, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

When to Replace Filters

Filter Indicator Light When to Service When to Replace

Pre-Filter none PermanentClean once every 14 days

Deodorization Filter none

Can NOT be WASHED

Every 3 months

True HEPA Filter

Lasts up to

12months

• When the Check Filter Indicator LED is on, it is time to replace the Filter.

• Intervals between filter replacement may vary depending on environment.

MAINTENANCE

INITIAL OPERATION

REPLACING FILTERS

Resetting Filter Life:

After replacing your True HEPA Filter, place the Pre-Filter back in and close the Front Panel.

While the unit is on, hold the Filter Reset Button for at least 5 seconds until you hear the beep.

After the beep, the Filter Replacement Indicator will disappear. The True HEPA Filter is now reset.

Remove the front panel by grasping its upper edge

and gently pulling forward.

Remove the Pre-Filter, then the bag of filters behind

it.

Remove filters from protective plastic bag.

Install the filters until they fit securely in place.

03. True HEPA Filter (back)

02. Activated Carbon Filter (middle)

01. Pre-Filter (front)

After filters are installed, close the front panel.

Insert the power cord into an electrical outlet.

Latch

FRONT

PACKAGE CONTENTS

BACK

Control Panel

Front Panel

Air Outlet

Vent

Handle

Power Plug

Unit

(1) Pre-Filter

(8) Activated Carbon Filters

(2) True HEPA Filters

Wi-Fi Setup Guide

User

Manual

WHERE TO USE

MODEL PART DIAGRAM

30~45cm

Allow 30~45cm. of space between TVs, radios, and

other electronics.

Electromagnetic interference from

certain electronics may cause product malfunction.

Place indoors away from direct sunlight.

Direct

exposure may cause product malfunction or failure.

Only place on hard, flat surfaces.

Flimsy or slanted

surfaces may result in abnormal noise and vibrations.

Allow at least 30~45cm. from walls for maximum air

flow

True HEPA Filter

Activated Carbon Filter

PlasmaWave® TechnologyPre-Filter

4-STAGE AIR PURIFICATION

Air Purification means it

removes inanimate particles

01. Auto Mode Indicator - The LED "Auto"

light will indicate when Auto Mode is

activated.

02. Air Quality Indicator - Color coded LED

light indicates one of three levels of Air

Quality: Red (poor), Amber (fair), and Blue

(good).

03. Fan Speed Indicator - Indicates the

current fan speed.

04. Sleep Mode Indicator - The LED "Sleep"

light will indicate when Sleep Mode is on.

05. Filter Replacement Indicator - LED light

indicates when it is time to change the filter.

06. Filter Reset Button - After replacing the

True HEPA Filter, use a small object such as a

paper clip, to press and hold the Filter Reset

Button for at least 5 seconds until the Filter

Replacement Indicator turns off.

07. Smart Sensor - Detects the amount of

odorous gas in the environment. When in

Auto mode, the fan speed adjusts according

to the detected amount of gas.

08. Power Button -

Turns the unit on or off.

During the first 30 seconds of powering up,

the Air Quality Indicator will cycle through

Blue, Amber and Red colors.

• Smart sensor takes approximately 4 minutes

to detect the air quality in the environment

before normal operation begins.

09-1. Fan Speed/Auto/Sleep Buttons -

Use

the Fan Speed arrow buttons to set the

desired fan speed. Fan Speeds cycle over

in this sequence: Auto, Low, Medium, High,

Turbo, Sleep, Auto.

Auto Mode:

Automatically adjusts fan speeds

according to your indoor air quality. The fan

speed will adjust to low when air quality is

good, medium when fair, and to high when poor.

Sleep Mode: When Sleep Mode is activated,

the Air Quality Indicator LED light is disabled.

• Fan speed will automatically set to minimum

speed (lower than 'Low') which will be

nearly silent. When Sleep Mode is active,

PlasmaWave

will be disabled, but it can be

turned back on.

09-2. PlasmaWave

Button - Press and hold

the buttons

for 3 seconds

Press the Plasmawave

button when the unit

is on to enable or disable this feature. By

default, PlasmaWave

is enabled whenever

the unit is powered on. When the unit is

running, you may hear a chirping or buzzing

sound. The sound is from particles passing

through PlasmaWave

, it is normal and does

not signify product failure.

10. PlasmaWave

Indicator - Indicates

whether PlasmaWave

is enabled or disabled.

11. Wi-Fi Button -

Press for 3 seconds to

activate pairing mode. When Wi-Fi is paired,

press the button to turn Wi-Fi off or back on.

12. Wi-Fi Indicator -

Enables or disables the

Wi-Fi feature. When in the pairing state, the Wi-

Fi LED flashes. When paired successfully, the

Wi-Fi LED will be a solid white light.

13. Light Sensor - Detects the amount of

ambient light in the environment. When in

Auto Mode, the light sensor detects when to

put the unit into Sleep Mode.

Winix Smart Wi-Fi Setup - Refer to the Wi-Fi

Guide provided inside the box.

CONTROL PANEL

07 08 09 11 13

02 03 04 05 0601

1210

CLEANING CARE

Cleaning the Filters:

Use a vacuum cleaner or soft brush to

clean the Pre-Filter.

• If it is excessively soiled, rinse in room

temperature water. Do not use detergent or

soap.

Allow the filter to dry for 24 hours or

more before using.

Intervals between filter

cleaning may vary depending on the air

quality. Do not use hot water over 40

C or

volatile fluids such as paint thinner.

Cleaning the Exterior & Interior:

Wipe with a soft damp cloth using room

temperature water.

• Afterwards, wipe it down with a dry cloth.

Open the front panel and clean the interior

with a vacuum cleaner.

• For optimal performance, clean every

1-2months.

N O T I C E

• When cleaning the unit, always unplug the power cord

first and then wait until the unit has cooled down.

• Never disassemble, repair, or modify this unit yourself.

• Do not use flammable sprays or liquid detergents.

• Do not allow children to clean or maintain the unit.

• Before cleaning or maintaining, ensure unit is

unplugged.

• Do not use benzene, alcohol, or other volatile fluids,

which may cause damage or discoloration

SPECIFICATIONS

Model C545(AU)

Voltage AC 220 V - 240 V, 50 / 60 Hz

Power Rate 65 W

Dimensions

350 mm (W) x 215 mm (D)

x 524 mm (H)

Weight 5 kg

Filter SKU Filter GA : 1712-0096-12

Exterior design, and product specifications may be changed

without prior notice to improve product performance.

AUSCLIMATE FILTER CLUB

For exclusive savings on replacement filters ausclimate.com.au/pages/filter-club

New Zealand

PO Box 100707

North Shore Mail Centre

Auckland 0745

www.cdbgroup.com

Australia

PO Box 574

South Morang

Victoria 3752

www.cdbgroup.com

Produkt Specifikationer

Mærke:	Ausclimate
Kategori:	Luftrenser
Model:	C545

Har du brug for hjælp?

Hvis du har brug for hjælp til Ausclimate C545 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Luftrenser Ausclimate Manualer

Ausclimate C545 Manual

12 August 2025

Ausclimate ACD245 Manual

30 Juli 2025

Ausclimate ACD200 Manual

30 Juli 2025

Ausclimate ACD220SG Manual

30 Maj 2025

Ausclimate ACD225 Manual

30 Maj 2025

Luftrenser Manualer

Nyeste Luftrenser Manualer

Novatek F0700 Manual

5 December 2025

SPT AC-9966 Manual

4 December 2025

Honeywell AirBRIGHT UV2400U2000/U Manual

29 November 2025

TCL Breeva A1W Manual

28 November 2025

Wood's TALL 155 Manual

28 November 2025

Honeywell AirBRIGHT UV2400U6000/U Manual

28 November 2025

Klarstein DryFy Grand Smart 70 Manual

28 November 2025

Klarstein DryFy Pro Manual

27 November 2025

Klarstein DuraDry 70L Manual

27 November 2025

TCL Breeva A1C Manual

27 November 2025