Avanti HRS10321B Manual

Avanti Vault HRS10321B

Læs gratis den danske manual til Avanti HRS10321B (4 sider) i kategorien Vault. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Avanti HRS10321B, eller vil du spørge andre brugere om produktet?

Side 1/4
MODEL HRS10321B
SECURITY SAFE
INSTALLATION AND USAGE INSTRUCTIONS
Your Avanti Room Security Safe is supplied with the following:
1 – Security Safe Unit
2 – Emergency Access Keys
1 – Installation / Usage Guide
1 – Felt Liner
Installation Screw Kit
4 – Rubber Feet
INSTALLING YOUR SECURITY SAFE
When installing your safe, be sure the location is sturdy enough to support the unit and is both
secure and easy to access.
Safe can be installed onto either a concrete or wooden surface.
When installing use a 25/64” (10mm) drill bit and screws.
To prevent removal of your security safe, it is recommended to use Allen type screws (not included)
to affix the unit to the installation location.
INITIAL SETUP AND CONFIGURATION.
After you have installed the unit in its final location, proceed to set up digital access controls.
1) Using the emergency Access Key, open the safe.
2) Open the battery compartment cover.
3) Following the image shown in the battery compartment install 4 AA sized batteries.
4) Close the battery compartment cover.
5) Using the keypad, enter the initial setup password “1234” or the administrator password
“888888”.
NOTE:
Battery Life / Level: Always replace all of the batteries at the same time. If at any time the battery
level is too low to operate the security safe, use the emergency access key.
Safety / Security Feature: If the passcode is entered incorrectly more than 3 times the keypad will
go into lock mode. After approximately (1 5) fifteen minutes the keypad will return to normal
working function.
Interior Light: When the safe is unlocked using the keypad, the interior light will turn on and will
turn off automatically after approximately 30 seconds.
Automatic Door Opening: When the safe is unlocked using the keypad the door will automatically
open slightly outward to allow easy / quick access to contents stored in the safe.
RESETTING THE ADMINISTRATOR PASSWORD
To reset the access code read and follow the steps below.
1) With the door open, press the s,Clear key twice, the Yellow Light flashe enter old master code
(default “ ”8-8-8-8-8-8 )
2) one acoustic signals ( will come (Itbeep) s mean old master code is right, if old master code is
wrong, three beep beep beep acoustic signals ( ” “ ” “ ) will come), enter a new master code of 6 digits ,
one aco ustic signals (beep) will come.
3) Re long - inter the new master code, the Green Light flashes and one acoustic signals (beep~ ),
indicates new master code changed successfully.
GUEST / USER CODE SETUP
To reset the access code read and follow the steps below.
1) With the door CLOSED, enter a new 3 – 6 digit code and press the “LOCK” key to confirm the new
pass code.
2) You will hear and see the security lock engage.
3) Enter the new pass code to open the security safe.
4) Close the door and enter the new code set up in step # 1 and press the “LOCK” key.
5) If the Guest / User enters the wrong pass code three (3) times in a row the keypad will go into
security-lock mode and will remain locked for approximately (1 (15) fifteen minutes. After the 5)
f ifteen minutes has elapsed the keypad will return to normal operation.
Avanti Products
Miami, FL 33172
In the event of service is sues, please call the
Customer Hotline at 1-800 220 5570 -


Produkt Specifikationer

Mærke: Avanti
Kategori: Vault
Model: HRS10321B

Har du brug for hjælp?

Hvis du har brug for hjælp til Avanti HRS10321B stil et spørgsmål nedenfor, og andre brugere vil svare dig