AVTech - Velleman CAMCOLD-CK Manual

AVTech - Velleman Sikkerhed CAMCOLD-CK

Læs gratis den danske manual til AVTech - Velleman CAMCOLD-CK (20 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om AVTech - Velleman CAMCOLD-CK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/20

CAMCOLD/CK_v2 1 VELLEMAN

CAMCOLD/CK – CONTROLLER KEYBOARD FOR DOME CAMERA

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on this unit or the package indicates that disposal of this unit after its lifecycle could harm the

environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be brought to a specialized

company for recycling.

This unit should be returned to your distributor or to a local recycling service.

Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities

Thank you for buying the CAMCOLD/CK! If the device was damaged in transit, contact your dealer.

2. Features

• Can control up to 99 cameras

• Ability to control 99 normal scanner heads, 1 scanner head, low speed scanner head (less than 24°/sec),

variable speed scanner head

• Joystick makes for easy manipulation

• Each scanner head can have 64 pre-programmed positions

• Delay time can be set between 1~60 sec

• Presets: only available on dome cameras disposing of the preset function

• Clearly legible LCD display

• RS-485 interface

• Normal scanner head / control electronic lens and scanner head via decoder (each decoder has 2 ON/OFF

switches)

• Normal recording/lens all in one scanner head

• Low speed scanner head can have 64 pre-positions, slow speed control (<24°/sec)

• High speed, variable speed scanner head can have 64 preset points, variable speed control

3. Specifications

• Power: adapter 9-12VDC / 400mA (not included)

• Control protocol: RS-485

• Transfer speed: 9600 bit/sec

• Dimensions: 265 x 175 x 80mm

• Weight: 0.95kg

4. Connection

1 (grey), 2 (white) – DC 9V-12V

3 (black), 4 (red) – RS485 control A

5 (green), 6 (yellow) – RS485 control B

7 (blue), 8 (brown) - Ground

CAMCOLD/CK_v2 2 VELLEMAN

ATTENTION: Please be careful on the sequence of pin wires - colour

• Signal A: Connect all cameras together on connector RS-485-A (connector K2)

• Signal B: Connect all cameras together on connector RS-485-B (connector K2)

• Do not inverse A with B.

• Connect all connections from keyboard connector A with camera connector 1A, camera connector 2A, …

1. Control wires: Connect the RS485 A and B wires from the keyboard to the A and B wires respectively

from the camera, the A and B wires respectively from the port of the scanner head, etc.

2. Terminal resistance: Connect a terminal resistance of 120Ω to the 2 extreme points of the decoder or

scanner head. Other components do not need resistance.

3. Matching resistance of 120Ω: Wires or ON/OFF switches are on the keyboard. Jumper K4 in the

keyboard is for the matching resistance. When switched to ON, the resistance is connected to the

extremity; otherwise, on effect.

1. Connecting 1 dome camera (with PELCO-D protocol)

1. Connect controller signal A to camera signal A.

2. Connect controller signal B to camera signal B.

3. Establish the camera address as address 1 (00000001) see 4.1

4. Establish the camera protocol (standard protocol is PELCO-D protocol). Usually, you do not need to change

the protocol because the controller uses the Pelco-D protocol.

See 4.1 to change the protocol.

You can also modify the protocol by using the “F4” button on the controller.

4.1 How to set up the PELCO-D protocol

On the camera (bottom of the camera) there is a DIP switch enabling you to adjust the address and the

protocol of the camera. The first six switches are for the address (from 1 to 63). It is possible to connect 64

cameras. The last 2 switches serve to set up the protocol.

12345678 = DIP switch nr.

Address 1 => 00000001 Characters in bold and italic: Pelco-D protocol

Address 2 => 10000001 78

Address 3 => 01000001 01

Address 4 => 11000001

Address 5 => 00100001

Address 6 => 10100001

Address 7 => 01100001

Address 8 => 11100001

Address 9 => 00010001

Address 10 => 10010001

Etc.….

‘1’ in the table means the switch is ON; ‘0’ in the table means the switch is OFF.

4.2 How to set up the PELCO-P protocol

12345678 = DIP switch nr.

Address 1 => 00000010 Characters in bold and italic: Pelco-P protocol

Address 2 => 10000010 78

Address 3 => 01000010 10

Address 4 => 11000010

Address 5 => 00100010

Produkt Specifikationer

Mærke:	AVTech - Velleman
Kategori:	Sikkerhed
Model:	CAMCOLD-CK

Har du brug for hjælp?

Hvis du har brug for hjælp til AVTech - Velleman CAMCOLD-CK stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Sikkerhed AVTech - Velleman Manualer

AVTech - Velleman CAMTVI6 Manual

23 August 2024

AVTech - Velleman DVR4T1 Manual

23 August 2024

AVTech - Velleman CAMCOLD23 Manual

22 August 2024

AVTech - Velleman CAMCOLBUL2N Manual

22 August 2024

AVTech - Velleman DVR16H3 Manual

22 August 2024

AVTech - Velleman DVR16T1 Manual

22 August 2024

AVTech - Velleman NVR3 Manual

22 August 2024

AVTech - Velleman CAMCOLBUL28 Manual

20 August 2024

AVTech - Velleman CAMIP13 Manual

19 August 2024

AVTech - Velleman CAMCOLBUL36 Manual

16 August 2024

Sikkerhed Manualer

Nyeste Sikkerhed Manualer

Aritech SHATTERPRO 3 Manual

15 Januar 2025

Axis Camera Station S9001 Mk II Desktop Terminal Manual

15 Januar 2025

Eminent EM6511 Manual

15 Januar 2025

Ranex RX2567-Z Manual

11 Januar 2025

NetworX NX-595E IP Communication Module Manual

5 Oktober 2024

Provision-ISR NVR2-4100P Manual

23 September 2024

Gira 0342 Manual

23 September 2024

Unitron Smart Alert Systeem Manual

23 September 2024

Netatmo Welcome Manual

21 September 2024

NetworX NX-408 Manual

20 September 2024