Be Quiet! Dark Rock Pro 4 Manual

Be Quiet! CPU kølere Dark Rock Pro 4

Læs gratis den danske manual til Be Quiet! Dark Rock Pro 4 (2 sider) i kategorien CPU kølere. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Be Quiet! Dark Rock Pro 4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

First remove the protective foil from the underside of the cooler.

Spread the thermal paste (17) on the surface of the CPU. The

amount supplied is sufﬁcient for one or two applications.

Caution: The thermal paste supplied is not suitable for human

consumption. If swallowed, drink lots of water and urgently

seek medical attention. Keep it out of the reach of children.

Avoid contact with skin and eyes.

Position the cooler mounting bridge (7) centrally on the cooler.

Next place the cooler unit over the CPU. Loosen both heatpipe

caps that are found in the middle of the top side of the cooler.

Insert the Intel/AMD mounting bridge fastening screws (12)

from above into the cooler mounting bridge and then screw

these alternately tight.

You can use the cross-tip screwdriver (16) for this.

Subsequently retighten both heatpipe caps on the top side of

the cooler.

Fasten the 120mm fan (3) using fan clips (18) onto the front

side of the cooler. Slide the 135mm fan (2) between the two

heatsinks and also fasten this with fan clips (18). Connect

both fans using the the Y cable (20). Connect this to the

CPU fan connector on the motherboard.

When dismantling the fans, push the notches of the fan

clips (18) away from the fan.

Position the cooler mounting bridge (7) centrally on the cooler

(1). Next place the cooler unit over the CPU. Loosen both

heatpipe caps that are found in the middle of the topside of the

cooler (rotate as illustrated). Insert the Intel/AMD mounting

bridge fastening screws (12) from above into the cooler

mounting bridge (7) and then screw these alternately tight. You

can use the cross-tip screwdriver (16) for this.

Subsequently retighten both heatpipe caps on the top side of

the cooler.

Fasten the 120mm fan (3) using fan clips (18) onto the front

side of the cooler. Slide the 135mm fan (2) between the two

heatsinks and also fasten this with fan clips (18). Connect

both fans using the the Y cable (20). Connect this to the

CPU fan connector on the motherboard.

When dismantling the fans, push the notches of the fan

clips (18) away from the fan.

Introduction: Thank you for deciding to purchase a be quiet!

product. The following instructions will guide you through the

installation process. If you do encounter installation problems,

please don't hesitate to contact our customer services by

mailing service@bequiet.com. Please note that be quiet!

cannot accept liability for damage caused by compatibility

problems.

Warranty:

• 3 years manufacturer guarantee for consumers (original

purchase from authorized be quiet! dealers only)

• Guarantee work can only be processed with an included

copy of the purchase receipt from an authorized be quiet!

dealer

• Manipulation and structural changes of any kind as well

as damages through external mechanical forces lead to a

complete voiding of the guarantee

• Our General Warranty Conditions apply, which can be

viewed on bequiet.com

Listan GmbH & Co.KG . Biedenkamp 3a . 21509 Glinde

Germany

For further information contact us via e-mail:

service@bequiet.com

SCOPE OF DELIVERY

General

We recommend preparatory mounting of the

cooler outside the PC case for subsequent

installation.

The following parts are needed for this:

1x Dark Rock Pro 4 CPU cooler (1), 1x 135mm fan (2), 1x 120mm

fan (3), 2x Intel mounting brackets (5), 1x cooler mounting

bridge (7), 4x Intel spacer nuts (8), 4x mounting bracket

fastening screws (11), Intel/AMD mounting bridge fastening

screws (12), 1x cross-tip screwdriver (16), 1x thermal paste

(17), 4x fan clips (18), 1x Y cable (20)

Assembly of the cooler mounting frame

First screw the Intel spacer nuts (8) onto the threads of the

socket frame. Place the Intel mounting brackets (5) over the

Intel spacer nuts and screw these tight with the mounting

bracket fastening screws (11). You can use the cross-tip

screwdriver (16) for this.

First remove the protective foil from the underside of the cooler.

Spread the thermal paste (17) on the surface of the CPU. The

amount supplied is sufﬁcient for one or two applications.

Caution: The thermal paste supplied is not suitable for

human consumption. If swallowed, drink lots of water and

urgently seek medical attention. Keep it out of the reach of

children. Avoid contact with skin and eyes.

Installation video

1366, 2011(-3) square ILM, 2066

1150, 1151, 1155, 1156

General

We recommend preparatory mounting of the

cooler outside the PC case for subsequent

installation.

The following parts are needed for this:

1x Dark Rock Pro 4 CPU cooler (1), 1x 135mm fan (2), 1x 120mm

fan (3), 1x Intel backplate (4), 2x Intel mounting brackets (5),

1x cooler mounting bridge (7), 4x Intel 115X/1366 nuts (9), 4x

mounting bracket fastening screws (11), 2x Intel/AMD mounting

bridge fastening screws (12), 4x Intel backplate screws (13), 4x

O-rings (15), 1x cross-tip screwdriver (16), 1x thermal paste (17),

4x fan clips (18), 1x Y cable (20)

Mounting the backplate

Position the Intel backplate screws (13) in the notches situated

on the rear side of the Intel backplate (4). Pay attention in so

doing to align with the holes specially drilled for each socket.

For ﬁxing the backplate screws onto the Intel backplate use

the O-rings (15). Once assembly of the Intel backplate for the

respective Intel socket is complete, position it under the

motherboard. In so doing make sure that the Intel backplate

screws (13) are precisely positioned inside the motherboard

holes.

Assembly of the cooler mounting frame

Screw the Intel 115X/1366 nuts (9) onto the previously

positioned Intel backplate (4). Then position the Intel mounting

brackets (5) over the Intel 115X/1366 nuts and afﬁx these with

the mounting bracket fastening screws (11). You can use the

cross-tip screwdriver for this (16).

1366, 2011(-3) square ILM, 2066

1150, 1151, 1155, 1156

Intel LGA 2011(-3) square ILM / LGA 2066 Intel LGA 1150 / 1151 / 1155 / 1156 / 1366

We recommend removal of the cooler prior to transportation.

January 2018

Part name Quantity

be quiet! Dark Rock Pro 4 cooler 1

135mm fan 1

120mm fan 1

Intel backplate 1

Intel mounting brackets 2

Short AMD mounting brackets 2

Cooler mounting bridge 1

Intel spacer nuts 4

Intel 115X/1366 nuts 4

Part name Quantity

AMD spacer nuts 4

Mounting bracket fastening

screws 4

Intel/AMD mounting bridge

fastening screws 2

Intel backplate screws 4

AMD backplate screws 4

O-rings 4

Cross-tip screwdriver 1

Thermal paste 1

Fan clips 2

AM3 washers 4

Y cable 1

Installation video

1366

1150, 1151,

1155, 1156

Produkt Specifikationer

Mærke:	Be Quiet!
Kategori:	CPU kølere
Model:	Dark Rock Pro 4
Type:	Køler
Bredde:	136 mm
Dybde:	162.8 mm
Højde:	123.7 mm
Vægt:	1130 g
Produktfarve:	Sort
Pakkevægt:	1390 g
Pakkedybde:	181 mm
Pakkebredde:	205 mm
Pakkehøjde:	212 mm
Omdrejningshastighed (maks.):	1500 rpm
Materiale:	Kobber
Kabellængde:	0.22 m
Harmoniseret systemkode (HS):	84733080
Bæredygtighedscertifikater:	RoHS
Støjniveau (lav hastighed):	12.8 dB
Støjniveau (høj hastighed):	24.3 dB
Antal blæsere:	2 blæser(e)
Passende til rumtype:	Processor
Skruer inkluderet:	Ja
Ventilator diameter:	120/135 mm
Strømforsyning:	1.92 W
Thermal Design Power (TDP):	250 W
Ventilatorstik:	4-polet
Understøttede procesorsokler:	LGA 1150 (Socket H3),LGA 1151 (Socket H4),LGA 1155 (Socket H2),LGA 1200 (Socket H5),LGA 1700,LGA 2011 (Socket R),LGA 2011-v3 (Socket R),LGA 2066,Socket AM4,Socket AM5
Understøttelse af puls-bredde modulering (PWM):	Ja
Nominel strøm:	0.16 A
Nominel spænding:	12 V
Ventilator dimensioner (BxDxH):	135 x 135 x 22 mm
Varmerør diameter:	6 mm
Antal varmerør:	7
Lejetype:	Fluid Dynamic Bearing (FDB)
Lamelmateriale:	Aluminium
Antal lameller:	90
Ekstra ventilator understøttes:	Ja