Behringer 297 Dual Portamento/CV Utilities Manual

Behringer Syntese maskine 297 Dual Portamento/CV Utilities

Læs gratis den danske manual til Behringer 297 Dual Portamento/CV Utilities (2 sider) i kategorien Syntese maskine. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Behringer 297 Dual Portamento/CV Utilities, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

V 1.0

Quick Start Guide

SYSTEM 100

297 DUAL PORTAMENTO/

CV UTILITIES

Legendary Analog Portamento

Controller and CV Utilities for Eurorack

Controls

(1) MIXER SIG IN – Connect incoming signals via 3.5 mm

TS cables. Inputs 3 and 4 feed +10/-10 V respectively to

the mixer inputs if no jack is inserted, which can be used

to oset the overall mixer output control voltage.

(2) PORTA SIG OUT – Send the portamento signal to another

module via 3.5 mm TS cable.

(3) PORTA SIG IN – Connect a signal to the portamento

section via 3.5 mm TS cable.

(4) SIG LEVEL – Adjust the level of the signals connected to

the mixer inputs.

(5) INV OUT – Send the mix of inputs 1-4 as an

inverted signal.

(6) NON INV OUT – Send the mix of inputs 1-4 as a

non-inverted signal.

(7) TIME – Adjust the portamento time.

(8) CV IN – Connect a voltage to control the portamento time

from another module.

(9) +10/-10 V LEVEL – Adjust the level of the +10 V and

-10 V outputs.

(10) +10/-10 V OUT – Send the +10 V and -10 V signals via

3.5 mm TS cable.

Power Connection

The module comes with the required power cable for connecting

to a standard Eurorack power supply system. Follow these

steps to connect power to the module. It is easier to make

these connections before the module has been mounted into

a rack case.

1. Turn the power supply or rack case power o and

disconnect the power cable.

2. Insert the 16-pin connector on the power cable into the

socket on the power supply or rack case. The connector has

a tab that will align with the gap in the socket, so it cannot

be inserted incorrectly. If the power supply does not have

a keyed socket, be sure to orient pin 1 (-12 V) with the red

stripe on the cable.

3. Insert the 10-pin connector into the socket on the back of

the module. The connector has a tab that will align with the

socket for correct orientation.

4. After both ends of the power cable have been securely

attached, you may mount the module in a case and turn on

the power supply.

(1)

(4)

(5)

(6)

(3)(2)

(7)

(8)

(10)

(9)

Produkt Specifikationer

Mærke:	Behringer
Kategori:	Syntese maskine
Model:	297 Dual Portamento/CV Utilities

Har du brug for hjælp?

Hvis du har brug for hjælp til Behringer 297 Dual Portamento/CV Utilities stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Syntese maskine Behringer Manualer

Behringer 2-XM Manual

3 Juni 2025

Behringer STEPS Manual

30 Januar 2025

Behringer WAVE Manual

2 Januar 2025

Behringer PHARA-O MINI Manual

2 Januar 2025

Behringer Eurorack GO Manual

15 November 2024

Behringer RS-9 Manual

10 Oktober 2024

Behringer K-2 MK II Manual

30 September 2024

Behringer UB-Xa D Manual

30 Juli 2024

Behringer Proton Manual

30 Juli 2024

Behringer MODEL 15 Manual

7 Juli 2024

Syntese maskine Manualer

Nyeste Syntese maskine Manualer

Roland JUNO-D8 Manual

1 Juni 2025

Qu-Bit Chance Manual

4 Marts 2025

Twisted Electrons TWISTfm FM Manual

2 Februar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

Twisted Electrons hapiNES L Manual

30 Januar 2025

Twisted Electrons MEGAfm MKII Manual

30 Januar 2025

Twisted Electrons MEGAfm Manual

30 Januar 2025