Behringer Sample & Hold / Random Voltage Module 1036 Manual

Behringer Synthesizer Sample & Hold / Random Voltage Module 1036

Læs gratis den danske manual til Behringer Sample & Hold / Random Voltage Module 1036 (9 sider) i kategorien Synthesizer. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Behringer Sample & Hold / Random Voltage Module 1036, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

Quick Start Guide

(EN) Controls

(1) LED - Indicates that clock A or B is engaged.

(2) CLOCK FREQ - Sets the clock frequency value.

(3) CLOCK RANGE - Determines whether the value selected

with the associated Clock Frequency knob is interpreted

by a factor of 1/10th or x10. For example, a setting

of 50 on the knob will either result in 5 Hz or 500 Hz.

(4) SAMPLE - Manually generate a sample command pulse.

(5) CLOCK ON/OFF - Engage clock A and B pulse generators

independently. Clock A can be assigned to both sample

and hold sections if desired.

(6) TRIG/GATE - Determines whether a short trigger

or longer gate will open the sampler. In the trigger

position, the positive edge of the pulse will open the

sampler for about 10 ms, whereas the gate position

will hold the output of the sampler open for the entire

duration of the positive pulse.

(7) INT RANDOM SIG - Adjusts the level of the internal

random signal generator, which can be used instead

of or in addition to an external signal.

(8) EXT SIG - Attenuates the signal connected

to the EXT IN jack.

(9) CLOCK FREQ MOD - Attenuates the signal connected

to the FM IN jack.

(10) EXT IN - Connect an external voltage which will be

sampled and manipulated.

(11) SAMPLE - Connect an external oscillator or keyboard

trigger to generate a sample command pulse.

(12) FM IN - Connect a voltage to control the clock frequency

modulation of the pulse generator.

(13) OUT - Send the sample to other modules

via 3.5 mm TS cable.

Power Connection

The unit comes with the required power cable for connecting

to a standard Eurorack power supply system. Follow these

steps to connect power to the module. It is easier to make these

connections before the module has been mounted into a rack case.

1. Turn the power supply or rack case power o and

disconnect the power cable.

2. Insert the 16-pin connector on the power cable into the

socket on the power supply or rack case. The connector has

a tab that will align with the gap in the socket, so it cannot

be inserted incorrectly. If the power supply does not have

a keyed socket, be sure to orient pin 1 (-12 V) with the red

stripe on the cable.

3. Insert the 10-pin connector into the socket on the back of

the module. The connector has a tab that will align with the

socket for correct orientation.

4. After both ends of the power cable have been securely

attached, you may mount the module in a case and turn on

the power supply.

V 1.0

SAMPLE & HOLD / RANDOM

VOLTAGE MODULE 1036

Legendary 2500 Series Dual Sample

and Hold with Voltage Controlled Clock

Module for Eurorack

(3)

(4)

(5)

(2)

(1)

(8)

(9)

(6)

(7)

(13)(12)

(10)

(11)

Installation

The necessary screws are included with the module for mounting

in a Eurorack case. Connect the power cable before mounting.

Depending on the rack case, there may be a series of xed holes spaced

2 HP apart along the length of the case, or a track that allows individual

threaded plates to slide along the length of the case. The free-moving

threaded plates allow precise positioning of the module, but each plate

should be positioned in the approximate relation to the mounting

holes in your module before attaching the screws.

Hold the module against the Eurorack rails so that each

of the mounting holes are aligned with a threaded rail or threaded

plate. Attach the screws part way to start, which will allow small

adjustments to the positioning while you get them all aligned.

After the nal position has been established, tighten the screws down.

2SAMPLE & HOLD / RANDOM VOLTAGE MODULE 1036

Produkt Specifikationer

Mærke:	Behringer
Kategori:	Synthesizer
Model:	Sample & Hold / Random Voltage Module 1036

Har du brug for hjælp?

Hvis du har brug for hjælp til Behringer Sample & Hold / Random Voltage Module 1036 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Synthesizer Behringer Manualer

Behringer JT MINI Manual

2 Januar 2025

Behringer WAVES Manual

2 Januar 2025

Behringer SWORDS Manual

2 Januar 2025

Behringer Bode Frequency Shifter 1630 Manual

14 December 2024

Behringer Concert CDP2400USB Manual

29 September 2024

Behringer MS-5 Manual

2 September 2024

Behringer Spring Reverberation 646 Manual

1 September 2024

Behringer CP3A-M Mixer Manual

1 September 2024

Behringer RADAR Manual

25 August 2024

Behringer PRO-VS MINI Manual

25 August 2024

Synthesizer Manualer

Nyeste Synthesizer Manualer

Nystrom Crum Hum Manual

10 Marts 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

11 Januar 2025