Beltronics GT-360 Manual


Læs gratis den danske manual til Beltronics GT-360 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Beltronics GT-360, eller vil du spørge andre brugere om produktet?

Side 1/10
Programming
Press BRT to go from Press VOLUME + orto change
one category to the next your setting within a category
User Mode Access and customize all Settings and Preferences
Advanced*
Novice Access and customize units and display color, (all other
Settings are set to factory defaults)
NOTE: Switch back to Advance mode to view all Preferences
Pilot Scan Bar* Scanning Bar with Full Word
Full Word Full Word: AutoScan, Auto NoX, or Highway
Display Color Set color to match your vehicles dash displayCopper*/Blue/Green/Red
Speed Display Displays current speedOn*
O Displays battery voltage
Cruise Alert Oers double beep alert tones below specied speedO/ 20-160 mph
20 mph*
Over Speed Reminds you when you exceed a specied speedO / 20-160 mph
70 mph*
Meter Mode Single band with front and rear signal strength bar graphsStandard*
Tech Single band with numeric frequency and front and rear
signal strength bar graphs
Basic Simple messages replace bands:
Caution (if traveling below cruise alert limit)
Slow Down (if traveling above cruise alert limit)
Tones Standard* Standard Beltronics alert tones
Mild Mild doorbell chime alert tones
AutoMute Low/Med*/High/O
Automatically reduces audio to preferred volume during alert
AutoLock On* / O Automatically stores and locks out false alarms
Units English*/Metric Units for distance and speed
Language English*/Espanol Language for voice and text
Voice On* / O Voice announcements
GPS Filter Enables GPS-powered featuresOn* / O
Press and hold the BRT and SEN buttons to access Programming. To exit Programming, simply wait a few
seconds without pressing a button. The unit will display to conrm your selections.
Completed
7
AutoPower O Power turns on or odepending on your vehicle’s ignition
type (constant power or switched)
1 Hour Powers oautomatically after 1 hour
2 Hours Powers o automatically after 2 hours
4 Hours* Powers o automatically after 4 hours
8 Hours Powers o automatically after 8 hours
NOTE: If AutoPower is on, to save screen life the display screen goes
blank after 30 minutes without moving.
Band Enables Default SettingsDefault*
Modied Band Enables have been modied from their default settings
Press SEN to go from one Press VOLUME + orto change
band category to the next your setting within a category
X Band On* / O
K Band Freq: 24.050-24.250 GHz On* / O
NOTE: When K Band is o, you can select separate segments of the
band to turn on or o.
KN1 On* / O Freq: 24.050 - 24.110 GHz
KN2 On* / O Freq: 24.110 - 24.175 GHz
KN3 On* / O Freq: 24.175 - 24.250 GHz
KN4 On / O* Freq: 23.950 - 24.050 GHz
Ka Band Freq: 33.400-36.000 GHzOn* / O
NOTE: When Ka Band is o, you can select separate segments of the band to turn
on or o.
KaN1 On / O* Freq: 33.400 - 33.700 GHz KaN6 On / O*
Freq: 34.800 - 35.160 GHz
KaN2 On / O* Freq: 33.700 - 33.900 GHz KaN7 On / O*
Freq: 35.160 - 35.400 GHz
KaN3 On* / O Freq: 33.900 - 34.200 GHz KaN8 On* / O
Freq: 35.400 - 35.600 GHz
KaN4 On* / O Freq: 34.200 - 34.600 GHz KaN9 On / O*
Freq: 35.600 - 35.840 GHz
KaN5 On* / O Freq: 34.600 - 34.800 GHz KaN10 On / O*
Freq: 35.840 - 36.000 GHz
Ka Band On* / O
Ka-POP On / O*
Laser On* / O
TSR On* / O Automatically rejects trac ow sensors-monitoring false alarms
Marker Enable Default SettingsOn* / O
Modied Marker Enables have been modied from their default settings
NOTE:
AutoPower only
works with constant
power ignition
8


Produkt Specifikationer

Mærke: Beltronics
Kategori: Ikke kategoriseret
Model: GT-360

Har du brug for hjælp?

Hvis du har brug for hjælp til Beltronics GT-360 stil et spørgsmål nedenfor, og andre brugere vil svare dig