Benro Adventure Monopod MAD49A Manual

Benro Stativ Adventure Monopod MAD49A

Læs gratis den danske manual til Benro Adventure Monopod MAD49A (2 sider) i kategorien Stativ. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Benro Adventure Monopod MAD49A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Classic Series Monopods

Operating Instructions

Thank you for making Benro your choice for professional photographic

equipment. Your Benro gear is manufactured to provide years of

dependable service. In order to obtain optimum satisfaction and

performance, we suggest that you carefully read these instructions.

Speciﬁcations and design are subject

to change without notice.

75 Virginia Road

North White Plains, NY 10603

T 914.347.3300

F 914.347.3309

info@BenroUSA.com

BenroUSA.com

SETUP

Head Mounting (FIGURES 1 & 2)

If your Monopod did not come with a Head,

select one of the fine Benro Ballheads or

Tilthead that match your size Monopod

and install by screwing the Head clockwise

onto the 3/8" Mounting Thread of the Top

Plate. Once it is hand tight, secure by fully

tightening the Head Locking Screw(s) (on

select models) from below.

Most Heads have a 3/8" Base Mount so your

Benro Monopod is shipped with the 3/8

Mounting Thread exposed, but if the Head

you choose uses a 1/4–20 you can attach it

by simply reversing the Mounting Screw.

To do this turn the Locking Nut counter-

clockwise (using the supplied Wrench)

until it becomes loose, and unscrew the

Mounting Screw until it can be completely

removed. Reverse the Screw, so that the

threads are in position and screw it back

into place, secure with the Locking Nut

using the wrench.

NOTE: Allow enough of the screw threads

to be available for maximum security when

the Head is mounted onto the Monopod.

It’s recommended that at least 5 to 6

threads be exposed before locking the

Mounting Screw in place.

OPERATION

Before using your Monopod, adjust each

Leg Section to the desired height.

Make sure that the Monopod is firmly resting

on a stable surface and mount your camera

securely on the Monopod Head. Always

engage any safety locks on the Monopod

Head to prevent any accidental dismounting.

FOR BEST RESULTS: Do not raise the

Monopod higher than necessary and extend

the largest diameter Leg Sections first.

NOTE: Never carry your Monopod with

camera gear attached.

Leg Section Adjustment (FIGURES 3 & 4)

Each Leg Section can be adjusted to the

desired length by opening the Flip Lock

Lever so the Leg is free to slide in or out.

Once the desired length is achieved, snap

the Flip Lock Lever closed so that the leg

section is securely locked. Repeat this step

for each Leg Section until the Monopod is

set to the desired height.

NOTE: To prevent any accidental damage

to your gear, always remove any mounted

equipment (camera, etc.) from the Monopod

before adjusting the Leg Sections.

User Adjustments (FIGURE 5)

Flip Lock Lever tension is adjusted using the

3mm Allen Key plus the special Six-sided

Socket Wrench built into the plastic clip

which comes attached to the monopod leg.

USER NOTICE

• Do not exceed the maximum specified

load capacity (see specifications at

www.BenroUSA.com).

• Always ensure that Leg and Head Locks

are tightly engaged before mounting any

gear on your Monopod.

• Always clean and dry any Monopod after

it has been exposed to wet, dusty, sandy

or salty conditions. Your Monopod is

not recommended for use in salt water.

If required, clean Monopod using a mild

soap solution applied with a soft cloth,

rinse with fresh water and dry with soft

towel. Remove any dust, dirt or sand

from all Leg Locks, Leg Sections and all

moving parts.

• Do not leave any Monopod in the sun

for prolonged periods and avoid high

temperature exposure.

• Avoid leaving any Monopod or Tripod

unattended in areas where people could

trip over the equipment and get hurt.

• Remove camera, lens, and all gear from

the Monopod when transporting.

• For your safety, don’t let your Benro

gear come in contact with any electrical

power source.

Top Plate

Flip Lock Lever

Closed Cell Foam Grip

Wrist Strap

Rotating Pod Foot

Locking Nut

1/4-20 + 3/8

Mounting Screw

Wrench

Unlock Lock

3 4

3mm Allen Key

6-sided Socket

Wrench Clip

Operating Instructions & User Notice

Produkt Specifikationer

Mærke:	Benro
Kategori:	Stativ
Model:	Adventure Monopod MAD49A

Har du brug for hjælp?

Hvis du har brug for hjælp til Benro Adventure Monopod MAD49A stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Stativ Benro Manualer

Benro S4 Pro Manual

8 December 2024

Benro S8Pro Manual

8 December 2024

Benro S2Pro Manual

8 December 2024

Benro ITrip FIT19AIH0 Manual

7 Oktober 2024

Benro BV4PRO Manual

2 Oktober 2024

Benro KH25N Manual

20 September 2024

Benro Video Monopod A48FDS4 Manual

7 September 2024

Benro HD3A Manual

4 September 2024

Benro C2573FS4 Manual

1 September 2024

Benro Adventure Monopod MAD49A Manual

4 August 2024

Stativ Manualer

Nyeste Stativ Manualer

Glide Gear G2H 100 Manual

3 April 2025

Sachtler FSB 14T Mk II Manual

2 April 2025

Proaim P-MLAK-01 Manual

2 April 2025

Proaim LV-SCFH-01 Manual

2 April 2025

Proaim P-G-PM Manual

2 April 2025

Proaim P-OHCR-01 Manual

2 April 2025

Proaim P-LLBT-MTCL Manual

2 April 2025

Proaim P-TNGO-01 Manual

2 April 2025

Proaim VI-GLDE-01 Manual

2 April 2025

Oben CT-3431 Manual

2 April 2025