Benro B3 Manual

Benro Stativ B3

Læs gratis den danske manual til Benro B3 (2 sider) i kategorien Stativ. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Benro B3, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
B Series Double-Action Ballheads
75 Virginia Road
North White Plains, NY 10603
T 914.347.3300
F 914.347.3309
info@BenroUSA.com
BenroUSA.com
Operating Instructions
Thank you for making Benro your choice for professional photographic
equipment. Your Benro gear is manufactured to provide years
of dependable service. In order to obtain optimum satisfaction and
performance, we suggest that you carefully read these instructions.
Specifications and design are subject
to change without notice.
Mounting Screw
Stop Screws (2)
Head Locking Knob
Mounting Screw
Mounting Platform
Bubble Level
SETUP
Head Mounting
Install by screwing the head clockwise onto
the 3/8" Mounting Thread of the Top Plate of
the Tripod or Monopod. Once it is hand tight,
secure by fully tightening the Head Locking
Screw(s) (on select models) from below.
OPERATION
The B Series Double-Action Ballheads are
professional black anodized machined
aluminum and feature three operating
Knobs. Drag control is manually adjusted
and locked, along with independent
Panning. Plus a Universal Quick Release
Clamp with secondary Safety Lock System
is incorporated.
Universal Quick Release Plate System
The B Series Double-Action Ballheads
feature a Universal Quick Release Plate
system. It offers a quick method of
mounting or releasing a Camera or
Equipment from the Head. It’s important
that the correct Quick Release Plate be used
along with the proper mounting screw
(1/4–20 is included as the standard size
but spare 1/4–20 and 3/8 plates of various
lengths are available as accessories). Extra
Plates are recommended as you can screw
one to each Camera or Lens for even greater
convenience when rapidly mounting
and dismounting gear. And because of
compatibility with the Universal system,
most plates and special brackets from other
manufacturers can be used as well.
Quick Release Lock (FIGURE 1)
When used properly, the Quick Release
Lock offers two levels of security for your
gear. To remove the Quick Release Plate,
turn the Quick Release Locking Knob
counter-clockwise. A partial opening of
the clamping mechanism allows the Quick
Release Plate to slide on the Mounting
Platform for proper balance and positioning.
Two Stop Screws (removable) on the bottom
of the Quick Release Plate provide this first
level of security. An additional counter-
clockwise turn of the Quick Release Locking
Knob opens the clamp fully so that the
Quick Release Plate can be tilted out to
be removed. Reverse the process and
tighten the Quick Release Locking Knob
to secure the Quick Release Plate.
Ballhead Controls (FIGURE 2)
A large Head Locking Knob locks the
Ballhead in place. Once the Knob is
turned counter-clockwise and loosened,
the Ballhead can move freely allowing
the Mounting Platform to be positioned
anywhere within a 0–90° vertical
orientation. This movement is expanded by
the use of the Pan Locking Knob
which adds a 360° Panning range. The Pan
control is fully independent and positioning
can be adjusted easily and accurately by
using the Graduated Panning Scale and
Pointer on the Base of the Ballhead.
When the Head Locking Knob is released,
it is possible to move the Ballhead with
some resistance or Drag. To achieve the
proper degree of Drag, mount the intended
camera or equipment onto the Ballhead.
While holding the camera/lens loosen the
Head Locking Knob until it is released.
Turn the Drag Control Knob clockwise to
increase Drag, and counter-clockwise to
decrease it.
FOR OPTIMUM RESULTS: Adjust the Drag
under the weight capacity, temperature
and conditions under which the Ballhead
will be used.
NOTE: Do not over tighten any Locking
Knobs as this could damage the Ballhead
locking mechanism.
USER NOTICE
• Do not exceed the maximum specified
load capacity (see specifications at
www.BenroUSA.com).
• Always ensure that all Ballhead locks are
tightly engaged before mounting any gear.
• Always clean and dry any Ballhead after
it has been exposed to wet, dusty, sandy
or salty conditions. Your Ballhead is not
recommended for use in salt water. If
required, clean Ballhead using a mild
soap solution applied with a soft cloth,
rinse with fresh water and dry with soft
towel. Remove any dust, dirt or sand from
all locks and all moving parts.
• Do not leave any Ballhead in the sun
for prolonged periods and avoid high
temperature exposure.
• Avoid leaving any Tripod or Monopod
unattended in areas where people could
trip over the gear and get hurt.
• Remove camera, lens, and all gear from any
Tripod or Monopod when transporting.
• For your safety, don’t let your Benro
gear come in contact with any electrical
power source.
Drag Control Knob
Base
Pan Locking Knob
Quick Release
Locking Knob
1
2
Panning
Scale Pointer
360°
Operating Instructions & User Notice

Produkt Specifikationer

Mærke: Benro
Kategori: Stativ
Model: B3

Har du brug for hjælp?

Hvis du har brug for hjælp til Benro B3 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Stativ Benro Manualer

Benro

Benro S4 Pro Manual

8 December 2024
Benro

Benro S8Pro Manual

8 December 2024
Benro

Benro S2Pro Manual

8 December 2024
Benro

Benro ITrip FIT19AIH0 Manual

7 Oktober 2024
Benro

Benro BV4PRO Manual

2 Oktober 2024
Benro

Benro KH25N Manual

20 September 2024
Benro

Benro Video Monopod A48FDS4 Manual

7 September 2024
Benro

Benro HD3A Manual

4 September 2024
Benro

Benro C2573FS4 Manual

1 September 2024
Benro

Benro Adventure Monopod MAD49A Manual

4 August 2024

Stativ Manualer

Nyeste Stativ Manualer

Glide Gear

Glide Gear G2H 100 Manual

3 April 2025
Sachtler

Sachtler FSB 14T Mk II Manual

2 April 2025
Proaim

Proaim P-MLAK-01 Manual

2 April 2025
Proaim

Proaim LV-SCFH-01 Manual

2 April 2025
Proaim

Proaim P-G-PM Manual

2 April 2025
Proaim

Proaim P-OHCR-01 Manual

2 April 2025
Proaim

Proaim P-LLBT-MTCL Manual

2 April 2025
Proaim

Proaim P-TNGO-01 Manual

2 April 2025
Proaim

Proaim VI-GLDE-01 Manual

2 April 2025
Oben

Oben CT-3431 Manual

2 April 2025