Benro BH00 Manual

Benro Stativ BH00

Læs gratis den danske manual til Benro BH00 (2 sider) i kategorien Stativ. Denne vejledning er vurderet som hjælpsom af 56 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 28.5 anmeldelser. Har du et spørgsmål om Benro BH00, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

BH Series Single-Action Ballheads

75 Virginia Road

North White Plains, NY 10603

T 914.347.3300

F 914.347.3309

info@BenroUSA.com

BenroUSA.com

Operating Instructions

Thank you for making Benro your choice for professional photographic

equipment. Your Benro gear is manufactured to provide years of

dependable service. In order to obtain optimum satisfaction and

performance, we suggest that you carefully read these instructions.

Speciﬁcations and design are subject

to change without notice.

Camera Screw

Quick Release Plate

Bubble Level

Base

Plate Locking Lever

Ball Locking Lever

Security

Locking Lever

Mounting Platform

Head Mounting

Install by screwing the head clockwise onto

the 3/8" Mounting Thread of the Top Plate of

the Tripod or Monopod. Once it is hand tight,

secure by fully tightening the Head Locking

Screw(s) (on select models) from below.

OPERATION

The single-action Ball Locking Lever

controls all movements of the BH Series

Ballheads. When released, the Ballhead and

the Mounting Platform can move freely

within a 360° rotational adjustment. And

two U-shaped openings on opposite sides

provide 90° angular movement of the

Mounting Platform.

Quick Release Plate

The BH Series Single-Action Ballheads

incorporate a Quick Release Plate system.

It offers a quick method of mounting or

releasing a Camera or Equipment from the

Head. It’s important that the correct Quick

Release Plate be used along with the proper

mounting screw (1/4–20 is included as the

standard size but spare 1/4–20 and 3/8

plates are available as accessories). Extra

Plates are recommended as you can screw

one to each Camera or Lens for even greater

convenience when rapidly mounting and

dismounting gear.

Quick Release Locking Lever

(FIGURES 1, 2 & 3)

When used properly, the patented Dual

Lock Quick Release system offers two levels

of security for your gear. To remove the

Quick Release Plate, squeeze both the Plate

Locking Lever and the Security Locking

Lever and pull the larger Locking Lever

out. The Quick Release Plate will disengage

allowing it to be removed.

To reconnect the Quick Release Plate, insert

the angled part of the Plate into the groove

on the opposite side of the Locking Levers

and press down flat. The Locking Levers will

automatically engage the locking system and

will return to the safety lock position. Press

the Plate Locking Lever in firmly to secure.

Ball Locking Lever (FIGURE 4)

The single-action Ball Locking Lever is

spring-loaded and can be repositioned when

it is in the lock position to accommodate

any desired Lever position. To reposition,

gently pull on the Lever to disengage, and

then allow the spring to pull the lever back

to reengage.

NOTE: Do not over tighten the Locking

Lever as this could damage the Ballhead

locking mechanism.

1 2

360°

180°

• Do not exceed the maximum specified

load capacity (see specifications at

www.BenroUSA.com).

• Always ensure that all Ballhead locks are

tightly engaged before mounting any gear.

• Always clean and dry any ballhead after

it has been exposed to wet, dusty, sandy

or salty conditions. Your Ballhead is not

recommended for use in salt water. If

required, clean Ballhead using a mild

soap solution applied with a soft cloth,

rinse with fresh water and dry with soft

towel. Remove any dust, dirt or sand from

all locks and all moving parts.

• Do not leave any Ballhead in the sun

for prolonged periods and avoid high

temperature exposure.

• Avoid leaving any Tripod or Monopod

unattended in areas where people could

trip over the gear and get hurt.

• Remove camera, lens, and all gear from any

Tripod or Monopod when transporting.

• For your safety, don’t let your Benro

gear come in contact with any electrical

power source.

USER NOTICESETUP

Operating Instructions & User Notice

Produkt Specifikationer

Mærke:	Benro
Kategori:	Stativ
Model:	BH00

Har du brug for hjælp?

Hvis du har brug for hjælp til Benro BH00 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Stativ Benro Manualer

Benro S4 Pro Manual

8 December 2024

Benro S8Pro Manual

8 December 2024

Benro S2Pro Manual

8 December 2024

Benro ITrip FIT19AIH0 Manual

7 Oktober 2024

Benro BV4PRO Manual

2 Oktober 2024

Benro KH25N Manual

20 September 2024

Benro Video Monopod A48FDS4 Manual

7 September 2024

Benro HD3A Manual

4 September 2024

Benro C2573FS4 Manual

1 September 2024

Benro Adventure Monopod MAD49A Manual

4 August 2024

Stativ Manualer

Nyeste Stativ Manualer

Glide Gear G2H 100 Manual

3 April 2025

Sachtler FSB 14T Mk II Manual

2 April 2025

Proaim P-MLAK-01 Manual

2 April 2025

Proaim LV-SCFH-01 Manual

2 April 2025

Proaim P-G-PM Manual

2 April 2025

Proaim P-OHCR-01 Manual

2 April 2025

Proaim P-LLBT-MTCL Manual

2 April 2025

Proaim P-TNGO-01 Manual

2 April 2025

Proaim VI-GLDE-01 Manual

2 April 2025

Oben CT-3431 Manual

2 April 2025