Black And Decker JS350K Manual

Black And Decker Sav JS350K

Læs gratis den danske manual til Black And Decker JS350K (5 sider) i kategorien Sav. Denne vejledning er vurderet som hjælpsom af 104 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 52.5 anmeldelser. Har du et spørgsmål om Black And Decker JS350K, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/5
WARNING: Important Safety Warnings and Instructions
TO REDUCE RISK OF INJURY:
• Before any use, be sure everyone using this tool reads and understands all safety
instructions and other information contained in this manual.
• Save these instructions and review frequently prior to use and in instructing others.
WARNING: When using electric tools, basic safety precautions should always be
followed to reduce risk of fire, electric shock, and personal injury, including the following.
READ ALL INSTRUCTIONS
General Safety Warnings and Instructions for All Tools
•KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
•CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain. Don’t use
power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence
of flammable liquids or gases.
•GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces.
For example; pipes, radiators, ranges, and refrigerator enclosures.
•KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors
should be kept away from work area.
•STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-
up place — out of reach of children.
•DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was
intended.
•USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy-duty tool.
Don’t use tool for purpose not intended.
•DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving
parts. Rubber gloves and non-skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
•USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.
•DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
•SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it
frees both hands to operate tool.
•DON’T OVERREACH. Keep proper footing and balance at all times.
•MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool
cords periodically and if damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep handles dry, clean, and free
from oil and grease.
•DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when
changing accessories, such as blades, bits, cutters.
•REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys
and adjusting wrenches are removed from tool before turning it on.
•AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure
switch is off when plugging in.
•EXTENSION CORDS. Make sure your extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
overheating. The following table shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage
number, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more AWG
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
•OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
•STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you
are tired.
•CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions that may affect its operation. A guard
or other part that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction manual. Have
defective switches replaced by authorized service center. Do not use tool if switch does not
turn it on and off.
Safety Warnings and Instructions: Double Insulation
Double insulated tools are constructed throughout with two separate layers of electrical
insulation or one double thickness of insulation between you and the tool’s electrical system.
Tools built with this insulation system are not intended to be grounded. As a result, your tool is
equipped with a two prong plug which permits you to use extension cords without concern for
maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when
operating this tool. The insulation system is for added protection against injury resulting from
a possible electrical insulation failure within the tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICALREPLACEMENT PARTS. Repair or
replace damaged cords.
Safety Warnings and Instructions: Polarized Plugs
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk
of electric shock. When provided, this plug will fit in the polarized outlet only one way. If the
plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other repro-
ductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
CAUTION: Wear appropriate hearing protection during use. Under some conditions
and duration of use, noise from this product may contribute to hearing loss.
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min ........................minutes ......................alternating current
......................direct current no ........................no load speed
..........................Class II Construction ........................earthing terminal
........................safety alert symbol .../min ..................revolutions or
reciprocations
per minute
INSTRUCTION MANUAL
KEY INFORMATION YOU SHOULD KNOW:
• The saw cannot be turned on by only rotating the speed wheel the trigger must
be depressed.
•Securely tighten roller support guide before use.
• Pull up scroller knob completely before rotating.
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO
1-800-54-HOW-TO1-800-54-HOW-TO
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT
BEFORE RETURNING THIS PRODUCT BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALL
FOR ANY REASON PLEASE CALLFOR ANY REASON PLEASE CALL
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR PURCHASE,BLACK & DECKER
CALL .1-800-54-HOW-TO (1-800-544-6986)
IN MOST CASES, A BLACK & DECKER REPRESENTATIVE
CAN RESOLVE YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT,
GIVE US A CALL. YOUR FEEDBACK IS VITAL
TO THE SUCCESS OF BLACK & DECKER'S QUALITY
IMPROVEMENT PROGRAM.
(544-6986)
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
Cat. No. .JS350 Form No. 581989-00 Copyright © 2002 Black & Decker Printed in China
BLADE
LAME
SEGUETA
OUICK CLAMP™ BLADE CLAMP LEVER
LEVIER DU SERRE-LAME QUICK CLAMPmc
PALANCA DEL PORTA SEGUETAS QUICK CLAMP™
BLADE
LAME
SEGUETA
1
2
3
SPEED WHEEL
RÉGULATEUR DE VITESSE
PERILLA DE CONTROL DE VELOCIDAD
TRIGGER SWITCH
INTERRUPTEUR À DÉTENTE
GATILLO INTERRUPTOR
LOCK ON BUTTON
BOUTON DE VERROUILLAGE
EN MODE DE FONCTIONNEMENT
BOTON DE ENCENDIDO PERMANENTE
4
5
SHOE
PATIN
ZAPATA
REAR SCREW
VIS ARRIÈRE
TORNILLO TRASERO
ROLLER SUPPORT GUIDE SCREW
VIS DU ROULEAU PORTEUR
TORNILLO DE LA GUIA DE SOPORTE DE RODILLO
0
15
6
ANGLE ADJUSTMENT MARKINGS
MARQUES DE RÉGLAGE DE L’ANGLE
MARCAS DE AJUSTE ANGULAR
SCROLLER RELEASE BUTTON
BOUTON DE DÉGAGEMENT DU
MODE DE CHANTOURNAGE
BOTON DE LIBERACION DE CALADO
DUST BLOWER SWITCH
INTERRUPTEUR DU VENTILATEUR
INTERRUPTOR DEL SOPLADOR
DUST EXTRACTION
DÉPOUSSIÉRAGE
EXTRACCION DE POLVO
CUT LINE BLOWING
VENTILATION DE LA LIGNE DE COUPE
SOPLADO EN LA LINEA DE CORTE
7
8
910
SCREW
VIS
TORNILLO
V
V
V
V
V
V
V
V
V
VA
A
A
A
A
A
A
A
A
AR
R
R
R
R
R
R
R
R
RI
I
I
I
I
I
I
I
I
IA
A
A
A
A
A
A
A
A
AB
B
B
B
B
B
B
B
B
BL
L
L
L
L
L
L
L
L
LE
E
E
E
E
E
E
E
E
ES
S
S
S
S
S
S
S
S
SP
P
P
P
P
P
P
P
P
PE
E
E
E
E
E
E
E
E
EE
E
E
E
E
E
E
E
E
ED
D
D
D
D
D
D
D
D
DS
S
S
S
S
S
S
S
S
SC
C
C
C
C
C
C
C
C
CR
R
R
R
R
R
R
R
R
RO
O
O
O
O
O
O
O
O
OL
L
L
L
L
L
L
L
L
LL
L
L
L
L
L
L
L
L
LE
E
E
E
E
E
E
E
E
ER
R
R
R
R
R
R
R
R
RJ
J
J
J
J
J
J
J
J
JI
I
I
I
I
I
I
I
I
IG
G
G
G
G
G
G
G
G
GS
S
S
S
S
S
S
S
S
SA
A
A
A
A
A
A
A
A
AW
W
W
W
W
W
W
W
W
W
Catalog No. JS350
SAFETY WARNINGS AND INSTRUCTIONS: JIG SAWS
CAUTION: When cutting into walls, floors or wherever live electrical wires may be
encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by
insulated grasping surfaces to prevent electric shock if you cut in the live wire.
•KEEP HANDS AWAY from cutting area. Never reach underneath the material for any
reason.
•KEEP BLADES SHARP. Dull blades may cause the saw to swerve or stall under pressure.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Motor
Be sure your power supply agrees with nameplate marking. 120 volts, AC only means your
tool may be operated only with alternating current and with direct current.never
Voltage decrease of more than 10% will cause loss of power and overheating. All tools are
factory tested; if this tool does not operate, check the power supply.
ASSEMBLY/ADJUSTMENT SET-UP
Installing Blades
BEFORE INSTALLING BLADES, TURN OFF AND UNPLUG TOOL.
Your jig saw uses the Quick Clamp blade changing system. To install a blade, lift the Quick™
Clamp™ lever (Figure 1). Insert the saw blade shank fully into the blade clamp. Release the
lever and the blade will be clamped securely in place. The back of the blade should be almost
touching the roller support guide. Ensure the blade teeth are facing forward.
Roller Support Guide
The roller support guide on your jig saw improves its performance when cutting tough
materials by adding support to the blade. Adjust the support roller by loosening the screw on
the bottom of the shoe, as shown in Figure 2 and moving the roller so that it almost, but not
quite, touches the blade. Tighten the screw securely to lock the roller in place.
Switch
Your jig saw has a variable speed switch. To turn the saw on, squeeze the trigger switch, as
shown in Figure 3. Hold the trigger switch in as you rotate the speed wheel to the desired
setting.
The selected speed will be maintained, under reasonable loading, as you cut.
NOTE: The numbers on the speed wheel are for reference only. They do not represent any
particular speed.
To turn the tool off, release the trigger switch.
The tool can be locked on for continuous operation at any speed by squeezing and holding
the trigger switch while you depress the lock-on button. With the lock-on button depressed,
release the trigger switch and the tool will continue to run. To release from lock position,
squeeze and release the trigger switch once.
Although your saw will maintain speed and power, don t overload it as this could damage the’
motor. Use your saw only for its intended purpose. If it should overheat, turn it on at its highest
speed and run it without a load until it cools down.
SPEED TEETH
MATERIAL SETTING PER INCH
Soft Wood 6-MAX 7
Hard Wood 5-MAX 7
Plastic 4-6 14
Aluminum 3-6 14
Steel 2-4 24
Tile 1-3 24
Glass 1-3 32
Leather 4-6 0 (Knife Edge)
Rubber 4-6 0 (Knife Edge)
NOTE: Speed setting 1 is the slowest and MAX is the fastest.
Bevel Adjustment
TURN OFF AND UNPLUG TOOL.
Raise or remove the dust shield before bevel cutting.
To adjust the bevel angle, loosen the rear screw on the bottom of the shoe, as shown in
Figure 4. Pull the show backward slightly and set the shoe to the desired angle. Angle
adjustment is indicated on the raised portion of either side of the shoe (Figure 5). It is also
possible to push the shoe forward to set fixed positions of 0°, 15 , 30 or 45° ° °. A protractor is
recommended when very accurate cuts are required.
To reset the shoe for a square cut, loosen the rear screw and move the shoe until it is
approximately 90 to the blade. While applying slight forward pressure to the shoe, retighten°
the rear screw.
General Cutting
Be sure board is firmly secured. Hold jig saw by the handle and operate switch to turn the unit
on. Don t attempt to turn on the unit when blade is against material to be cut. This could stall’
the motor. Place front of shoe on material to be cut and hold jig saw shoe down firmly against
the work surface while cutting. Don t force the tool; let the blade cut at its own speed.’
Whenever possible, clamp or support work close to the line of cut; when the cut is completed,
shut off power and lay the saw aside before loosening the work.
Scrolling
Your jig saw is equipped with a manual scrolling feature which permits the saw blade to
completely rotate without rotating the entire saw.
NOTE: Before scrolling, retract the roller support guide and ensure the shoe is in the forward
position. Push the scroller release button, as shown in Figure 6. The scrolling knob will
pop up from the tool housing. Pull the knob up to confirm it has fully released. Using
one hand to guide the jig saw, turn the scroller knob to guide the blade along the line of the
cut. The blade will turn 360°.
The angle of the blade can be locked into one of four positions: 0°, 90 , 180 or 270° ° °. To lock
the blade in any of the four positions, push the scroller release button, and push the scrolling
knob down. When the button is released, the blade is locked into position.
To reset, push the scroller release button. To return to straight-line (non-scrolling) cutting,
press the scroller release button and push the knob down. Readjust the roller support guide
so it is almost touching the back of the blade.
Dust Extraction/Vacuum Attachment
Your jig saw is equipped with a dust extraction system which greatly reduces clean up time.
To extract dust:
•Insert the end of the supplied vacuum adapter into the dust extraction opening at the rear
of the saw. Attach a standard vacuum cleaner hose.
•Turn the dust blower switch (Figure 7) to the right.
•Turn on the vacuum. Turn on the jig saw and begin cutting.
Cut Line Blower
Your jig saw is equipped with a cut line blower to keep the work area clear of dust as you saw.
To use the blower, turn the dust blower switch (Figure 7) to the left.
Metal & Plastic Cutting
In cutting thin gauge sheet metals, it is best to clamp wood or plywood to the bottom of the
metal sheet; this will insure a clean cut without the danger of vibration or tearing of metal. Use
a fine-tooth blade for ferrous metals (for those that have an iron content); and use a coarser
blade for nonferrous metals (those that do not have an iron content).
Cutting thin metal will take longer than cutting relatively thick wood so do not be tempted to
speed up the process by forcing the saw. Spread a thin film of cutting lubricant along the
cutting line, (any light weight oil) and consult the blade chart in this manual to select the
proper saw blade for your application.
Use low speeds for cutting metals, plastics and composition tile. When cutting laminated
plastic, place the finished side down and use a fine tooth hollow ground blade.
Pocket Cutting
•Measure the surface to be cut and mark clearly with a pencil. Next tip the saw forward
until the front edge of the shoe sits firmly on the work surface, Figure 8.
•Switch the tool on and allow it to attain maximum speed.
•Grip the handle firmly and lower the back edge of tool until the blade cuts smoothly into
material. Always be sure blade reaches its complete depth before starting to cut. For
pocket cutting the selector should be kept in the straight cutting position.
Rip & Circle Cutting
Ripping and circle cutting without a pencil line are easily done with the rip fence and circle
guide (available at extra cost).
Use the screw supplied with the accessory. Position as shown in Figure 9 and thread the
screw into the shoe to clamp the fence securely.
Slide the rip fence under the screw from either side of the saw. Set the cross bar at desired
distance from blade and tighten screw. For ripping, the cross bar should be down as shown in
Figure 9. For circle cutting, the cross bar should be up, as shown in Figure 10.
When circle cutting, adjust rip fence so that distance from blade to hole in cross bar is desired
radius and tighten screw (use hole which lines up best with saw blade). Place saw so that
hole in cross bar is over center of circle to be cut (make pocket cut, drill hole for blade or cut
inward from edge of material to get blade into position). When saw is properly positioned,
drive a small nail through hole in cross bar. Using rip fence as a pivot arm, begin cutting circle.
Maintenance
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.
Accessories
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call: 1-800-
54-HOW-TO (544-6986)
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you. To find your local service location, refer to the yellow
page directory under “Tools Electric— ” or call: 1-800-54-HOW TO (544-6986)
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under “Tools-
Electric” in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state. Should you have any questions,
contact the manager of your nearest Black & Decker Service Center.
See Tools-Electric‘ ’
– Yellow Pages –
for Service & Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
JS350
GUIDE D’UTILISATION
RENSEIGNEMENTS IMPORTANTS
• éOn ne peut pas mettre la scie en marche en faisant tourner le r gulateur de
vitesse seulement; il faut enfoncer la détente.
• ’Bien serrer le rouleau porteur avant l utilisation.
• èSoulever compl tement le bouton de chantournage avant de le tourner.
CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.
AVERTISSEMENT : IMPORTANTES MESURES DE S CURITÉ É
AFIN DE RÉDUIRE LES RISQUES DE BLESSURES :
• ’ ’Avant toute utilisation, s assurer que tous ceux qui se servent de l outil lisent et
comprennent toutes les mesures de s et tout autre renseignement contenu dans leécurité
présent guide.
• é ’ ’ ’Conserver ces mesures et les relire fr quemment avant d utiliser l outil et d en expliquer le
fonctionnement à d’autres personnes.
AVERTISSEMENT : Afin de r duire les risques d incendie, de secousses é ’ électriques
ou de blessures lorsqu on utilise des outils lectriques, il faut toujours’ é
respecter les mesures de s suivantes.écurité
LIRE TOUTES LES DIRECTIVES.
MESURES DE S CURIT POUR TOUS LES OUTILSÉ É
•BIEN DÉGAGER LA SURFACE DE TRAVAIL. Des surfaces et des tablis encombré és
peuvent être la cause de blessures.
•TENIR COMPTE DU MILIEU DE TRAVAIL. Protéger les outils électriques de la pluie. Ne
pas s en servir dans des endroits humides ou mouill s. Bien clairer la surface de travail.’ é é
Ne pas se servir de l outil en pr sence de liquides ou de vapeurs inflammables.’ é
• É ÉSE PROT GER CONTRE LES SECOUSSES LECTRIQUES. Éviter tout contact avec
des objets mis la terre, comme des tuyaux, radiateurs, cuisini res, r rateurs et autresà è éfrigé
objets du genre.
•ÉLOIGNER LES ENFANTS. Tous les visiteurs doivent tre tenus cart de l aire deê à l’é ’
travail et il faut les emp cher de toucher outil ou au cordon de rallonge.ê à ’ l
• éRANGER LES OUTILS INUTILISÉS. Il faut ranger les outils dans un endroit sec, situ en
hauteur ou fermé à é é cl , hors de la port e des enfants.
•NE JAMAIS FORCER L’OUTIL. Afin d’obtenir un rendement s r et efficace, utiliser lû ’outil à
son rendement nominal.
•UTILISER L’ ÉOUTIL APPROPRI . Ne jamais exiger d’ ’un petit outil ou d un accessoire le
rendement d un outil de fabrication plus robuste. Se servir de l outil selon l usage pr’ ’ ’ évu.
•PORTER DES VÊ ÉTEMENTS APPROPRI S. É êviter de porter des v tements amples et des
bijoux qui peuvent tre happ s par les pi ces en mouvement. Porter des gants deê é è
caoutchouc et des chaussures semelle antid rapante pour travailler à é à ’ l ext rieur.é
Protéger la chevelure si elle longue.
•PORTER DES LUNETTES DE SÉ É É É ÉCURIT ET AUTRE QUIPEMENT DE S CURIT .
Porter des lunettes de protection ou de s crans lat raux, conformécurité à é é ément aux
normes de s appropri es, et, au besoin, un cran facial. Porter galement unécurité é é é
masque respiratoire si le travail de coupe produit de la poussière.
•NE PAS MANIPULER LE CORDON DE FAÇON ABUSIVE. Ne pas transporter l outil par le’
cordon ni tirer sur ce dernier pour le d brancher de la prise. loigner le cordon des sourcesé É
de chaleur, des flaques d huile et des ar tes tranchantes.’ ê
• è àASSUJETTIR LA PIÈCE. Immobiliser la pi ce l’ ’ éaide de brides ou d un tau. On peut
alors se servir des deux mains pour faire fonctionner l outil, ce qui est plus s’ ûr.
•NE PAS DÉPASSER SA PORTÉE. Toujours demeurer dans une position stable et garder
AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA RAI-
SON, PRI RE DE COMPOSERÉ
1 800 544-6986

Produkt Specifikationer

Mærke: Black And Decker
Kategori: Sav
Model: JS350K

Har du brug for hjælp?

Hvis du har brug for hjælp til Black And Decker JS350K stil et spørgsmål nedenfor, og andre brugere vil svare dig


Sav Black And Decker Manualer

Black And Decker

Black And Decker SM400 Manual

28 Juni 2024
Black And Decker

Black And Decker REVCJS12C Manual

28 Juni 2024
Black And Decker

Black And Decker CS1825L1 Manual

22 Maj 2024
Black And Decker

Black And Decker XTS1660KA Manual

20 Maj 2024
Black And Decker

Black And Decker BDCR18 Manual

6 Maj 2024
Black And Decker

Black And Decker JS700LK Manual

1 Maj 2024
Black And Decker

Black And Decker PHS550B Manual

23 April 2024
Black And Decker

Black And Decker JS700BL Manual

22 Februar 2024
Black And Decker

Black And Decker Q425K Manual

22 Februar 2024
Black And Decker

Black And Decker KFBES890 Manual

9 Februar 2024

Sav Manualer

Nyeste Sav Manualer

Dremel

Dremel CS12V Manual

13 Juni 2025
Metabo

Metabo BAS 505 Precision WNB Manual

9 Juni 2025
Mega

Mega 64000 Manual

9 Juni 2025
Metabo

Metabo ST 18 LT 130 Manual

8 Juni 2025
Metabo

Metabo STB 18 LT 130 Manual

8 Juni 2025
Metabo

Metabo BAS 505 Precision DNB Manual

7 Juni 2025
Draper

Draper 70833 Manual

7 Juni 2025
Draper

Draper 83677 Manual

6 Juni 2025
Draper

Draper Storm Force 98445 Manual

6 Juni 2025
Draper

Draper Expert 57489 Manual

6 Juni 2025