Black Decker ADE80 Manual

Black Decker Høvlemaskine ADE80

Læs gratis den danske manual til Black Decker ADE80 (7 sider) i kategorien Høvlemaskine. Denne vejledning er vurderet som hjælpsom af 66 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 33.5 anmeldelser. Har du et spørgsmål om Black Decker ADE80, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
8
ENGLISH
SURFACING/THICKNESSING ATTACHMENT ADE80 (TYPE 3)
Congratulations!
You have chosen an Elu product. Years of experience, thorough product
development and innovation make Elu one of the most reliable partners for
professional users.
Table of contents
Technical data en - 1
Manufacturer’s declaration en - 1
Safety instructions en - 1
Package contents en - 1
Description en - 2
Assembly and adjustment en - 2
Instructions for use en - 3
Maintenance en - 3
Guarantee en - 3
Technical data
Using MFF80/ Using HH40/
MFF81 HH40E
Max. surfacing width 90° mm 80 82
Max. surfacing width 45° mm 45 45
Max. thicknessing capacity mm 80 x 80 80 x 80
Max. planing depth mm 3.75 4.0
Thicknessing table mm 500 x 80 500 x 80
Surfacing fence length mm 350 350
Weight kg 3.7 3.7
Manufacturer’s Declaration
ADE80
Elu declares that the attachment mentioned above has been designed in
compliance with 89/392/EEC.
This attachment must not be put into service until it is established that the
Power Tool to be connected to this attachment is in compliance with
89/392/EEC (identified by the CE-marking on the Power Tool).
Director Engineering and Product Development
Horst Großmann
Elu International, Idstein, Germany
Safety instructions
Observe the safety regulations in the instruction manual of the Power
Tool to be connected to this attachment. Also observe any applicable
additional safety rules. Read the following safety instructions before
attempting to operate this product.
Keep these instructions in a safe place!
The attention of UK users is drawn to the “woodworking machines
regulations 1974” and any subsequent amendments.
General
• The attachment must be level and stable at all times.
• Keep the work top clear of foreign objects.
• Use the attachment with the Power Tools and accessories specified in
this manual only.
• Secure the Power Tool carefully.
• Work with closed hands.
• Make sure that your work area is properly lighted.
Surfacing/thicknessing
1 Dust extraction
As the planer produces dust and chips, the use of dust extraction
equipment is recommended. Proper dust extraction is especially
important if beech or oak dust is produced.
2 Wear safety goggles
Also use a face or dust mask to protect against dust or flying particles.
3 Protection devices
Only operate the Power Tool and attachment with all guards properly in
place.
4 Inspect workpiece
Remove any nails, staples and other metal parts.
5 Cutter blades
Use sharp and undamaged cutter blades only.
6 Damaged parts
Before operation, inspect the attachment, the Power Tool, the power
cable and the plug carefully for signs of damage. Have any damage
repaired by an Elu authorized repair agent before using the tool or
attachment.
7 Starting the planer
Before switching on, remove all adjustment spanners from the planer
and attachment.
8 Operating the planer and attachment
Do not overload the planer by feeding it at a too high rate. Always feed
the material against the rotational direction of the cutter block. Always
use a push stick, especially when working with smaller workpieces.
9 Stopping the planer
After switching off, the cutter block will continue to run for a few
seconds. Do not attempt to block it.
10 Maintain your attachment with care
Keep the attachment clean and in good condition for better and safer
performance. Follow the instructions for maintenance. Keep all controls
dry, clean and free from oil and grease.
11 Have your attachment repaired by an Elu authorized repair agent
This attachment is in accordance with the relevant safety regulations.
To avoid danger, it must only be repaired by qualified technicians.
Package contents
The package contains:
1 Surfacing/Thicknessing attachment
1 Support foot
1 Support bracket with foot
1 Support for handle
1 Switch edge for MFF80/MFF81
1 Switch strap for HH40/HH40E
1 Plastic bag containing:
5 screws
5 nuts
1 securing clip
2 fence securing knobs
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
en - 1
9
ENGLISH
en - 2
Description (fig. A1 & 2)
Your Elu Surfacing/Thicknessing attachment ADE80 (Type 3) has been
designed to extend the versatility of your MFF80/MFF81 or HH40/HH40E
planer by converting it into a compact planer/thicknesser.
A1
1 Switch strap
1a Switch wedge for use with HH40 models
2 Securing clip
3 Wing nuts
4 Bench clamp holes
5 Thicknessing adjuster
6 Aluminium frame
7 Thicknessing table
8 Table height adjuster
9 Thicknessing scale
10 Surfacing adjuster
11 Planing depth adjuster
12 Blade guard for thicknessing
A2
13 Reversible fence
14 Thicknessing table clamp
15 Fence securing knobs
16 Rear support foot
17 Support bracket with foot
18 Planer mounting rods
No-volt release switch
A no-volt release switch is available as an option (E38676). It offers the
following advantages:
- Optimum safety: It prevents the machine from restarting inadvertantly in
the event of a power loss.
- It allows easier switching of the planer.
Assembly and adjustment
Do not mount any Power Tools other than the MFF80/MFF81
or HH40/HH40E.
Assembling the attachment (fig. A & B)
The screws and nuts required to assemble the attachment are supplied
with the surfacing/thicknessing attachment.
• Slacken the thicknessing table clamp (14).
• Raise the thicknessing table (7) by rotating the table height adjuster (8).
• Mount the rear support foot (16), the arm (28) and support bracket with
foot (17) using the nuts and screws (21 through 27) as shown.
Mounting the planer (fig. C)
• Remove the wing nuts (3) and the securing clip (2).
• Hinge the planer mounting rods (18) up and mount the planer as
shown.
• Reinstall the wing nuts (3).
• Pivot the planer into surfacing or thicknessing position and tighten the
wing nuts (3).
• Fit the securing clip (2) in the appropriate groove of the rear mounting
rod.
Calibration (fig. A & D)
The calibration procedure needs to be performed only once.
• Remove the calibration fence (20) and place it on the thicknessing table (7),
gauge cams (29) up.
• Set the table height to 15 mm using the table height adjuster (8).
• Secure the adjustment using the thicknessing table clamp (14).
• Pivot the planer into thicknessing position and check that all four gauge
cams (29) are level against the planing shoe. Adjust as required.
• Tighten the wing nuts (3).
• Loosen the thicknessing table clamp (14) and lower the thicknessing
table (7).
• Remove the calibration fence and reinstall it in its original position as a
side guard.
Adjusting the planing depth
• For planing depth adjustment, refer to the instruction manual of the
planer.
• Make shallow cuts only, passing the material several times if required.
For optimal results, select a maximum planing depth of 1.5 mm.
Thicknessing position (fig. A & E)
• Remove the reversible parallel fence (13) by loosening the star knobs (15).
• Swivel the support bracket (17) aside or remove it and pivot the planer
into thicknessing position. The planer mounting rods (18) now rest in
the brackets (30).
Thicknessing table height adjustment (fig. A)
• Loosen the thicknessing table clamp (14).
• Raise or lower the table by rotating the table height adjustment screw (19).
• Tighten the thicknessing table clamp (14).
Surfacing position (fig. B & F)
• Remove the calibration fence.
• Loosen the thicknessing table clamp (14).
• Set the thicknessing table (7) to bottom position.
• Swivel the blade guard (12) aside and pivot the planer into surfacing position.
The planer mounting rod (18) now rests in the support bracket (17).
• Check that the rear of the planer rests on the arm (28 in fig. B).
• If required, loosen the screw (26) using a screwdriver.
• Adjust the arm (28 in fig. B) in its slot and secure the screw.
• Tighten wing nut (3) to lock the planer in surfacing position.
Mounting the reversible parallel fence (fig. A2)
• Lower the side guard of the planer and install the reversible parallel
fence (13).
• Tighten the star knobs (15).
• For 45° bevelled workpieces, remove the star knobs (15), reverse the
fence, refit the star knobs and level the fence on the planer shoe.
Adjusting the blade guard (fig. G)
The blade guard (12) is mounted on a support bracket (17) that can be
pivoted away when the planer is not in surfacing position. In surfacing
position, the bracket also serves as a support to the planer mounting rod.
The blade guard height is adjustable.
• Loosen the surfacing adjuster (10), adjust the blade guard height in the
slot (31) and tighten the screw.
Adjusting the planer in surfacing position to be 90° to the reversible
fence (fig. C & G)
The calibration procedure needs to be performed only once.
• Use a square to check that the angle is 90°.
If this is not the case:
• Remove the reversible fence (13).
• Loosen the wing nuts (3).
• Pivot guard (12) away.
• Pivot the planer up.
• Adjust the height adjustment screw (19) accordingly.
Dust extraction
• Use the dust extraction adapter of your planer and install it as
described in the instruction manual of the planer.

Produkt Specifikationer

Mærke: Black Decker
Kategori: Høvlemaskine
Model: ADE80

Har du brug for hjælp?

Hvis du har brug for hjælp til Black Decker ADE80 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Høvlemaskine Black Decker Manualer

Black Decker

Black Decker ADE80 Manual

16 August 2024

Høvlemaskine Manualer

Nyeste Høvlemaskine Manualer

Bosch

Bosch GHO 16-82 Professional Manual

29 September 2025
Scheppach

Scheppach HMS1070 Manual

19 September 2025
Einhell

Einhell TP-ET 18 Li BL Manual

6 September 2025
Full Boar

Full Boar FBWC-15125 Manual

26 August 2025
Einhell

Einhell TE-PL 920 Manual

21 August 2025
Toolson

Toolson PRO-MF 1320 Manual

20 August 2025
Toolson

Toolson PRO-HB 82 Manual

19 August 2025
Toolson

Toolson PRO-DF 860 Manual

19 August 2025
MSW

MSW -WOBD-1500L Manual

17 August 2025
Holzmann

Holzmann HOB 260ECO Manual

17 August 2025