Blaupunkt CIR-S1 Manual

Blaupunkt Alarmsystem CIR-S1

Læs gratis den danske manual til Blaupunkt CIR-S1 (2 sider) i kategorien Alarmsystem. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Blaupunkt CIR-S1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Curtain (C - PIR Motion Sensor IR S1)

1. LED indicator

The LED Indicator is under the front cover and is only visible

when turned on.

2. Battery Insulator

3. Tamper Switch

The Tamper switch protects the PIR from unauthorized cover

opening or removal from mounted surface

4. Learn/Test Button

Press the button to transmit a learn/test code and enter Test

mode for 3 minutes.

5. Supervision Enable/Disable Jumper Switch

(JP2)

6. High/Low Sensitivity Jumper Switch (JP3)

1 x PIR Sensor

2 x wall plugs and screws

1 x CR123A 3V lithium y - batter (pre installed)

Supervision Enable/Disable Jumper Switch (JP2)

If enabled, the PIR sensor will transmit supervision signal to

Control Panel periodically for the sensor to monitor PIR sensor

condition.

Jumper set to ON = supervision function is Disabled

Jumper set to OFF = supervision function is Enabled (Default)

High/Low Sensitivity Jumper Switch (JP3)

Jumper set to ON = PIR sensitivity is set to High

Jumper set to OFF= PIR sensitivity is set to Low (Default)

Put the Control Panel into learning mode, then press the learn

button to transmit learn code. Please refer to Control Panel

manual for to complete the learning process.

When mounted vertically, the PIR has a horizontal detection

coverage of 10 and vertical detection coverage of 110° ° to the

front. The PIR will only be activated by movemen across the 10t °

horizontal coverage.

Top View Side View

There are 3 ways to mount the PIR for different coverage

according to different scenarios

Mount the PIR on the wall vertically to protect against anyone

attempting to move across the detection area

When mounted at 1.4~1.7 meter height, the PIR has a detection

range of 10 meters against horizontal movement. Avoid mounting

outside suggested height or the detection range may be reduced.

HHoorriizzoonnttaall WWaallll MMoouunntt

Turn the PIR horizontally and mount on wall to protect against

vertical movement across the detection area. This practice is

usually used to protect against intruder from sky light and roof

hatch.

When mounted horizontally, the PIR has a detection range of 5

meters against vertically movement only It will NOT be able to .

detect horizontal movement.

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Off

if the jumper link is removed

parked on one pin.

Jumper On

The jumper link is inserted

connecting the two pins

Jumper Off

if the jumper link is removed

p .arked on one pin

CCeeiilliinngg MMoouunntt

Mount the PIR on ceiling to look downward over a door or

window.

When mounted at 2.4~3 meter height and looking down, the PIR

has coverage of about meters at ground level5

The PIR Sensor has knockouts on the back where plastic is

thinner for mounting t wall or ceiling .

1. Break through the knockouts; use the knockouts to mark

position on the wall or ceiling.

2. Drill holes into the marked location using the knockouts as

template.

3. Fix the PIR Sensor base onto the wall or ceiling the screws

and plugs provided.

4. Replace the PIR Sensor cover onto the base.

SSlleeeepp TTiimmeerr

The PIR ” of approximately 1 minute features a “sleep time for

power conservation . After transmitting a detected movement, the

PIR will not retransmit for 1 minute. Any further movement

detected during this sleep period will extend the sleep time by

another minute. In this way continuous movement in front of a

PIR will not unduly exhaust the battery.

Press the Test Button to enter Test mode for 3 minutes. Sleep

timer will be disabled under Test mode, and the LED indicator will

flash every time a movement is detected. Use the Test mode to

determine PIR detection coverage and plan the installation

location accordingly.

Off

Normal Operation

On (2 seconds)

- When Tamper Switch is triggered

- Movement detection under low battery,

tamper triggered, or Test mode.

The tamper switch spring is compressed against the break-away

area on PIR back cover when cover is closed. When the PIR

base is screwed onto mounting location, forceful attempt to

remove the PIR will cause the break-away area to detach and

activate tamper switch to notify Control Panel.

The PIR uses one CR123A batter 3V lithium y as its power source.

Remove the battery insulator to activate battery. It also features

low battery detection function to notify the Control Panel when

battery voltage is low.

When PIR is on low battery, follow the procedure below to

change the batteries.

1. Open the PIR back cover.

2. Remove the old battery.

3. Press the tamper switch several times to fully discharge.

4. Insert the new batteries observing correct polarity. The PIR

LED will light up for 30 seconds to indicate it is warming up.

5. Replace the PIR back cover.

EEnnvviirroonnmmeennttaall CCoonnddiittiioonn

- - 10°C to 40°C, relative humidity 85% non condensing.

868 MHz

Knockouts x 2)

Break away -

Area

Produkt Specifikationer

Mærke:	Blaupunkt
Kategori:	Alarmsystem
Model:	CIR-S1
Bredde:	76 mm
Dybde:	56 mm
Højde:	43 mm
Produktfarve:	Grey, White
Batterispænding:	3 V
Batteriteknologi:	Lithium
Driftstemperatur (T-T):	-10 - 45 °C
Forbindelsesteknologi:	Trådløs
LED-indikatorer:	Status
Strømkilde type:	Batteri
Monteringstype:	Loft
Batterilevetid:	3.5 År
Batteritype:	CR123A
Antal understøttede batterier:	1
Sensortype:	Infrarød sensor
Driftsfrekvens:	868 Mhz
Alarmfunktion:	Ja
Opdagelsesafstand:	10 m