Bogen ASM1 Manual

Bogen Ikke kategoriseret ASM1

Læs gratis den danske manual til Bogen ASM1 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Bogen ASM1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Easy Install

Amplified Speaker

Model ASM1

Speaker Layout

The layout of the speakers should be planned before installation

begins. Layout starts in one corner of the room. The first speaker

should be positioned from each wall a distance approximately

equal to the ceiling height of the room.

The next speaker in Row 1 should be spaced a distance approxi-

mately equal to twice the height of the ceiling. Each additional

speaker in the row should use this same spacing.

Row 2 starts at twice the ceiling height distance from row 1 and

twice the ceiling height from the wall. The other speakers in this

row are also spaced at twice the ceiling height.

Row 3 is again spaced at twice the ceiling height from the previ-

ous row. The first speaker starting this row is positioned at one

ceiling height distance from the wall (similar to row 1).

Continue this pattern of alternating rows until the room is covered.

Because of the wide sound dispersion characteristic of the ASM1,

exact placement is not critical. The spacing of the speakers can

be adjusted so that the speakers are evenly spaced in a row.

Speaker Installation

Step 1

Step 2

Step 3

STEP 1 - Position the speaker on the ceiling tile and slowly push

the speaker, forcing the studs through the ceiling tile.

STEP 2 - Clean any loose debris or conductive foil from around the

studs. Spin the wide-based wing nuts (supplied) down

the threaded studs. Tighten the wing nuts until they are

very snug (finger tighten only - no tools required). Check

that the speaker is drawn tight to the ceiling tile.

Fiberglass sleeves (supplied) should be placed over the

studs at this point to insulate the exposed portion of the

studs as a safety precaution.

STEP 3 - The electrical connections are made to the studs with the

wire nuts (supplied). The studs are color-coded to indi-

cate polarity.

Amplifier connections are:

Threaded COPPER stud – Audio Signal (+)

Threaded NICKEL stud – Audio Signal (-)

Smooth COPPER stud – 24V DC (+)

Smooth NICKEL stud – 24V DC (-)

Nylon wire ties (supplied) can be used to secure the speaker wires

to the studs if desired. (Nylon wire ties should wrap around the

fiberglass sleeve.)

54-2159-01B 1206

Specifications subject to change without notice.

Audio

Signal (+)

Audio

Signal (–) 24V DC (+)24V DC (–)

Volume Knob

Set volume to maximum (1) before

installation and adjust as needed

Produkt Specifikationer

Mærke:	Bogen
Kategori:	Ikke kategoriseret
Model:	ASM1
Type:	I væggen/på væggen/i loftet højttalere
Højde:	76.2 mm
Vægt:	907.18 g
Produktfarve:	Hvid
Strøm:	0.05 A
Pakkevægt:	1360.78 g
Wi-Fi:	Ingen
Bluetooth:	Ingen
Udgangseffekt (RMS):	1 W
Equalizer:	Ingen
Husmateriale:	Syntetisk ABS
Frekvensområde:	125 - 15000 Hz
Impedens:	2000 ohm (Ω)
Forbindelsesteknologi:	Ledningsført
Lyd-output kanaler:	1.0 kanaler
Højttaler, placering:	Kan monteres i loftet
Certificering:	NFPA NationalCode 160b\nUL-2043\n
Strømkilde type:	Vekselstrøm
Diameter:	241.3 mm
Fjernbetjent:	Ingen
Effektkrav:	12 - 30 VDC
Mikrofonindgang:	Ingen
Antal drivere:	1
Diskanthøjttaler:	Ingen
Sensitivitet:	90 dB
Plug and play:	Ja
Antal produkter inkluderet:	1 stk
Bas indstillinger:	Ingen
Bashøjttaler:	Ingen
Forstærker:	Indbygget
Højttaler kabinet:	Lukket
Subwoofer driver diameter (britisk):	4 "
Basrefleks:	Ingen