Bogen ASTB4 Manual

Bogen Ikke kategoriseret ASTB4

Læs gratis den danske manual til Bogen ASTB4 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Bogen ASTB4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

Description

The A-Series Terminal Boot is designed to offer added protection against the effects of

weather on wires and connections made to NEAR A-Series speaker model types A2, A6,

and A8. The ASTB4 package contains 4 terminal boots.

Note: The ASTB4 will not fit the NEAR A12 model.

Installation

1. If necessary, trim the tapering boot sleeve to accommodate the size of the wire bundle

to be attached to the speaker (adjust for a snug fit).

2. Slide the narrow end of the boot sleeve over the wires. Crimp any lugs onto the wires

after inserting the wires through the boot sleeve.

3. Secure the wires to the terminals and then slide the terminal boot into place over the

terminals, pressing it firmly against the terminal strip for a secure fit. The boot only fits

properly in one orientation.

Additional Protection

The terminal boot does not provide a water tight seal for the terminal strip. It is only

designed to minimize the direct effects of weather on the wires and connections.

Silicone-based caulks can be used to improve the seal of the boot to the speaker terminal

area. If desired, apply a bead to the base of the boot before pressing it onto the terminal.

Silicone sealents with adhesive properties adhere better than pure silicone products. The

boot sleeve exit can also be sealed, however, be certain to caulk it so that the caulk can

be removed later in case the boot needs to be removed.

Specifications subject to change without notice.

54-2085-01B 1104

50 Spring Street, Ramsey, NJ 07446, U.S.A.

Tel. 201-934-8500 • Fax: 201-934-9832

www.bogen.com

Model ASTB4

A-SERIES SPEAKER

TERMINAL BOOT

Note: The A2 speaker model does not allow enough space between the housing and the

bracket for the boot sleeve to pass between them. Therefore, it is important to install

the boot while the speaker is in its approximate final tilt position.

Produkt Specifikationer

Mærke:	Bogen
Kategori:	Ikke kategoriseret
Model:	ASTB4
Bredde:	50.8 mm
Dybde:	50.8 mm
Højde:	25.4 mm
Produktfarve:	Sort

Har du brug for hjælp?

Hvis du har brug for hjælp til Bogen ASTB4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Bogen Manualer

Bogen Nyquist NQ-IPHRN01 Manual

6 November 2025

Bogen AT10A Manual

6 November 2025

Bogen AT35A Manual

6 November 2025

Bogen ATP35 Manual

2 November 2025

Bogen Easy Design HS15EZ Manual

8 Oktober 2025

Bogen HS30EZ Manual

28 September 2025

Bogen CSD1X2U-V2 Manual

17 Juli 2025

Bogen SMTB Manual

10 Juli 2025

Bogen UTI1 Manual

6 Juli 2025

Bogen PCM2000 Manual

6 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

TOTO TSMX Manual

17 December 2025

Gamdias Aura GC2 Manual

17 December 2025

Vaxcel T0777 Manual

17 December 2025

Vaxcel T0696 Manual

17 December 2025

Vaxcel T0735 Manual

17 December 2025

Grundig Miami 49 VLX 9670 BP Manual

17 December 2025

Silverstone UC01 Manual

17 December 2025

Liteline P-4020 Manual

17 December 2025

Vaxcel T0376 Manual

17 December 2025

Vaxcel T0779 Manual

17 December 2025