Bogen TEL1S Manual

Bogen Blander TEL1S

Læs gratis den danske manual til Bogen TEL1S (3 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Bogen TEL1S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

TEL S1

Telephone Interface

Module

Features

• Loop start trunk interface

• Ground start trunk interface

• Page port interface

• Transformer-isolated

• Gain/Trim control

• Output signal gating

• Gating threshold and duration adjustments

• Variable threshold limiter

• 4 Levels of available priority

• Can be muted from higher priority modules

• Can mute lower priority modules

Specifications subject to change without notice.

54-2055-01D 0808

Gain

Provides control over the level of input signal that can be applied to the

internal signal buses of the main unit. Allows a way to balance the input

levels of various devices so that the main unit controls can be set to

relatively uniform or optimum levels. Clockwise rotation will increase

gain, counterclockwise rotation decreases gain.

Limiter (Limit)

Sets the signal level threshold at which the module will begin to limit the

level of its output signal. Clockwise rotation will allow more output

signal before limiting, counterclockwise rotation will allow less. The

limiter monitors the module’s output signal level, so increasing gain will

affect when limiting takes place.

Priority Level*

This module can respo

the highest priority. It m

muted. Priority 2 can

modules set for 3 or 4

modules and mutes Pri

by all higher priority mo

*The number of priorit

the modules are used i

Interface Type

Dry Loop - Use with pag

the telephone line.

Loop Start - Use when in

dedicated telephones. R

supply (see Block Diagr

Ground Start - Use only

connection of external

ground.

Jumper Selec

Bus Assignment

This module can be set

be sent to the main uni

Telephone System Connections

Connect the telephone system’s Tip line to the “T” terminal and the Ring

line to the “R” terminal. When interfacing to a ground start trunk, also

connect a wire from the PBX’s ground to the module’s “CM”

terminal. In some cases, the power supply’s ground connection alone will

be adequate. For Dry Loop (Page Ports), connect the audio pair to the

module’s “T” & “R” terminals (polarity insensitive). No power supply is

necessary. The module is audio-activated so a contact pair from the page

port is not needed.

Module Installation

1. Turn off all power to the unit.

2. Make all necessary jumper selections.

3. Position the module in front of desired module

bay opening, making sure that the module is

right-side up.

4. Slide the module onto the card guide rails. Make

sure that both the top and bottom guides are

engaged.

5. Push the module into the bay until the faceplate

contacts the unit’s chassis.

6. Use the two screws included to secure the

module to the unit.

WARNING:

Turn off power to unit and make all jumper

selections before installing module in unit.

Produkt Specifikationer

Mærke:	Bogen
Kategori:	Blander
Model:	TEL1S
Vægt:	79 g
Dimensioner (BxDxH):	25 x 76 x 76 mm
Frekvensområde:	10 Hz - 40 kHz
Effektkrav:	24VDC

Har du brug for hjælp?

Hvis du har brug for hjælp til Bogen TEL1S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Bogen Manualer

1 Marts 2025

1 Marts 2025

1 Marts 2025

1 Marts 2025

1 Marts 2025

1 Marts 2025

1 Marts 2025

1 Marts 2025

16 Februar 2024

20 Oktober 2022

Blander Manualer

Nyeste Blander Manualer

Rane CM 86 Manual

17 Juni 2025

DNA HLC 10 MK2 Manual

17 Juni 2025

16 Juni 2025

16 Juni 2025

16 Juni 2025

15 Juni 2025

15 Juni 2025

14 Juni 2025

13 Juni 2025

13 Juni 2025