Bogen TNG1S Manual


Læs gratis den danske manual til Bogen TNG1S (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 75 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 38 anmeldelser. Har du et spørgsmål om Bogen TNG1S, eller vil du spørge andre brugere om produktet?

Side 1/3
TNG S1
Tone Generator Module
Features
Select from burst/steady, slow whoop, siren, mechanical bell,
Klaxon, night ringer, double chime, and doorbell tones
Select 4 of 8 tones to trigger
Momentary and continuous playback modes
Screw terminal for 4 external trigger connections
Level control
Microprocessor-controlled operation
4 levels of available priority
Can be muted from higher priority modules
Can mute lower priority modules
Printed in Taiwan. 0209
© 2002 Bogen Communications, Inc.
54-2080-0 R21
Specifications subject to change without notice.
Module Installation
1. Turn off all power to the unit.
2. Make all necessary jumper selections.
3. Position module in front of any desired module bay opening, making sure that the module
is right-side up.
4. Slide module on to card guide rails. Make sure that both the top and bottom guides are
engaged.
5. Push the module in to the bay until the faceplate contacts the unit’s chassis.
6. Use the two screws included to secure the module to the unit.
WARNING:
Turn off power to unit and make all jumper
selections before installing module in unit.
Connections
Connect a contact closure between any of the “T” labeled terminals and the COM terminal to
trigger a tone playback.An open collector type output can also trigger operation.A ground
from the open collector triggering device must be connected to the COM terminal to com-
plete the conduction path.
Playback modes
One Time
When a trigger is applied and removed before the tone’s playback cycle finishes, the tone will
play only that one time and stop.A momentary trigger must be present for at least 0 ms to1
ensure that the TNG S will recognize it and no other tone can be playing when the trigger1
pulse is applied since the module ignores other triggers applied during tone playback.
Continuous
To cause continuous play of a tone, the trigger must be applied for the entire time during
which the tone is to play. Continuous play of a tone is actually a retriggering of the one time
tone cycle again and again.At the end of a tone’s playback cycle, the TNG S will recheck the1
status of this tone’s trigger. If it detects a trigger, it immediately retriggers the tone and causes
it to play again.This process continues until the trigger is removed. Once the trigger is
removed, the tone will finish its current tone cycle and stop. Some of the tones contain short
pauses between tone playbacks to make them sound proper when played as a continuous
train. A very short break in playback will occur during continuous operation of the mechanical
bell and 5 2 Hz steady tones.1
Trigger operation
There is no priority structure assigned to the different trigger inputs.Triggering is on a first-
come, first-serve basis.The internal microprocessor constantly scans the 4 trigger inputs for
activity and responds to the first trigger it detects as active. Once a tone is triggered, it takes
control of the module operation.All other triggers applied during the tone playback cycle will
be ignored. Once a tone has stopped, the microprocessor continues scanning through the trig-
ger inputs until it detects another trigger and begins playback of that tone.


Produkt Specifikationer

Mærke: Bogen
Kategori: Ikke kategoriseret
Model: TNG1S
Vægt: 57 g
Dimensioner (BxDxH): 25 x 76 x 76 mm
Frekvensområde: 10 Hz - 40 kHz
Effektkrav: 24VDC

Har du brug for hjælp?

Hvis du har brug for hjælp til Bogen TNG1S stil et spørgsmål nedenfor, og andre brugere vil svare dig