British Telecom Essentials Wi-Fi Extender 300 Manual

British Telecom Wifi repeater Essentials Wi-Fi Extender 300

Læs gratis den danske manual til British Telecom Essentials Wi-Fi Extender 300 (2 sider) i kategorien Wifi repeater. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 9 anmeldelser. Har du et spørgsmål om British Telecom Essentials Wi-Fi Extender 300, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Connection help

Don’t know if you’re connecting via router or extender?

• The extender’s network name is the same as your hub/router with ‘EXT-’ added to

the front. For example if your hub/router wireless network name is BTHub5-1234;

your new extended network name will be EXT- BTHub5-1234.

Can’t connect extender to router

• If the light on the extender keeps ashing red for more than 1 minute after connection

attempt. Check your hub/router is switched on and try moving your extender closer to it.

• If your device often loses internet access and the extender’s light is red because it is too far,

try moving the extender to another socket.

• If you are trying to use WPS but it doesn’t work (red light continues to ash), it may be

that it’s incompatible with the WPS function in the extender. Try to unplug and plug the

extender back in and repeat Method 1. If it still fails, follow the steps in Method 2, to

connect without using the WPS button.

• If you’re unable to connect using Method 2, check you have selected the correct

wireless network and you’ve entered the correct wireless key.

Can’t connect to internet

• Check your router is connected to the internet and is working correctly.your wi-

Can’t connect your device to wireless

• Make sure your device is correctly set-up to connect to your hub/router before trying

to use the extender.

• Microwaves and some electrical equipment may interfere with the wireless signal.

• Check the lights on your extender and make sure you are in good range (light is green),

if not see the section ‘Move extender to optimum location’.

• Thick/concrete walls and ceilings will aect wireless performance.

Light is o

• Check the power socket is working and switched on.

Light status

Light What’s happeningStatus

O Extender turned o

Flashing red slowly Slowly ashes red for 10 seconds whilst booting up

or when not congured yet with hub/router

Flashing red quickly Extender is connecting to hub/router. When ashing stops,

it’s ready for use

Red Extender too far from hub/router

Green Extender in good range from hub/router

Amber Extender too close to hub/router

After pressing the WPS/Link button

Amber ashing Authentication in progress

If WPS successful:

Flashing red quickly while connecting to the hub/router. Then turns either

steady green, amber or red depending on the range from the hub/router.

If WPS fails:

Flashing red slowly as not congured with hub/router

General information

For information on safety instructions,

technical information or setting up the

extender, please see the Frequently Asked

Questions at bt.com/essentials300

Guarantee

Your Essentials Wi-Fi Extender 300 is guaranteed for a

period of 3 years from the date of purchase. Subject to the

terms listed below, the guarantee will provide for the repair

of, or at BT’s or its agent’s discretion, the option to replace

the Essentials Wi-Fi Extender 300 or any component

thereof which is identied as faulty or below standard, or

as a result of inferior workmanship or materials. Products

over 28 days old from the date of purchase may be

replaced with a refurbished or repaired product.

The conditions of this guarantee are:

• the guarantee shall only apply to defects that

occur within the 3 year guarantee period

• proof of purchase is required

• the equipment is returned to BT or its agent

as instructed.

This guarantee does not cover any faults or defects caused

by accidents, misuse, fair wear and tear, neglect, tampering

with the equipment, or any attempt at adjustment or

repair other than through approved agents.

This guarantee does not aect your statutory rights.

To nd out what to do if your extender is in or

outside of the 3 year guarantee, please see the FAQ

at bt.com/essentials300

Reset to factory settings

If you need to access advanced settings,

have forgotten your password or if the

extender stops working you can reset it to

its factory settings.

1 Make sure the extender is plugged in.

2 Press the button for 1 second to Reset

restore factory default settings.

How to recycle your equipment

The symbol shown here and on the product

means that the product is classed as electrical

or electronic equipment, so DO NOT put it in your

normal rubbish bin.

It’s all part of the Waste Electrical and Electronic Equipment

(WEEE) Directive to recycle products in the best way – to be

kinder to the planet, get rid of dangerous things more safely

and bury less rubbish in the ground.

You should contact your retailer or supplier for advice on

how to dispose of this product in an environmentally friendly

way.

R&TTE Directive & Declaration of Conformity

This equipment complies with the essential requirements

for the Radio Equipment and Telecommunications Terminal

Equipment Directive (1999/5/EC).

For a copy of the Declaration of Conformity

please refer to bt.com/essentials300

This product uses open source codes available

from bt.com/help/gplcode

Power consumption

In operation

2.7 Watts

Network standby

2.14 Watts

Turn over for set-upTurn over for set-up

Oces worldwide

The services described in this publication are subject to availability and may be

modied from time to time. Services and equipment are supplied subject to

British Telecommunications plc’s respective standard conditions of contract.

Nothing in this publication forms any part of a contract.

Registered Oce: 81 Newgate Street, London EC1A 7AJ.

Registered in England No. 1800000.

Designed and produced by The Art & Design Partnership Ltd.

Printed in China / Issue 1 / ADP08-16

Find out more

• If you need more help, go to bt.com/essentials300 where

you can view Frequently Asked Questions.

• If you cannot nd the answer to your problem in the

Frequently Asked Questions, then please call our free

Helpline on 0808 100 6116

. Our dedicated advisors are

more likely to be able to help you than the retailer where

you made your purchase.

Box contents

Essentials Wi-Fi

Extender 300

Extender default settings

Please write the default settings from the label on the

back of the extender here.

Default Wi-Fi Network (SSID):

Default Wi-Fi Key:

Default Admin Password:

Essentials Wi-Fi

Extender 300

User Guide

3392 Essentials Wi-Fi Extender 300 QSG [5].indd 1 18/08/2016 12:53

Method 1 - Using WPS button

Connection to your router is very easy if it supports WPS; most recent routers do

(e.g. BT Home Hub 3 and later, or any other router that has a WPS button).

If your router doesn’t support WPS, go to ‘Method 2 - Without WPS button’ opposite.

1 Plug the extender into a power socket near your broadband wireless router

(e.g. in the same room). Wait 10 seconds for the extender to boot up. The light will

be ashing slowly red.

2 Press the button on your router.WPS

3 Press the button on the extender within 2 minutes.WPS (for 1 second)

4 Wait until the light stops ashing and turns either solid green, amber or red. The extender

is now congured with your hub/router, and you’re ready to nd its optimum location,

see

below. If this fails (the light stops ashing and starts ashing red), please use

‘Method 2 - Without WPS button’ opposite.

Note: the WPS button on your extender is only used to connect to the router and can’t

be used to connect devices.

3 Open your internet browser and enter http://192.168.1.1 in the address eld.

- Enter your extender’s (printed on the label on the back of the Admin password

device or written by you on the back of this user guide in the space provided),

then click .Login

- Click at the bottom then follow the on-screen connection wizard.Start

4 When you click your browser will lose connection to the extender Finish

(ignore browser errors). The extender’s light will stop ashing on successful connection.

The extender is now congured with your hub/router, and you’re ready to nd its optimum

location, see

below.

Full instructions on how to connect devices using dierent operating systems

are in the Frequently Asked Questions, available at bt.com/essentials300.

1 Plug in the extender halfway between your hub/router and the area you wish to

extend wi- to.

2 Give the extender 10 seconds to boot up. Once ready the extender’s light will change to a solid

green, amber or red depending on the signal quality and location. Ideally it will be solid Green

indicating a good range and you can go to step

Connect your devices.

If the light continues ashing red for more than 1 minute check you hub/router

is switched on and try moving your extender closer to it.

3 Check the lights and if necessary move the extender closer or further away

from your hub/router depending on the light status below. Your extender is in a

pretty good spot when showing a solid amber light, but you should aim to get a

solid green light for a good range and position.

1 The extender’s network name is the same as your hub/router with - EXT

added to the front.

For example:

Hub/router wireless network name: BTHub5-1234

New extended network name: EXT-BTHub5-1234

2 From your device, select the network you wish to connect to.

3 Enter the wireless key – this is the same as your hub/router.

2 Move extender to optimum location

Red (too far)

Move the extender closer to your hub/router.

Green (good range)

Good router signal strength. Ideal location for

maximum performance.

Amber (too close)

Move the extender further from the hub and

closer to the area you want to receive wi-.

It’s normal for the light to change occasionally.

1 Connect to your hub/router

If you need more help, go to bt.com/essentials300

or call *. 0808 100 6116

* alls made from within the UK mainland network are free. Mobile and international call costs may vary.C

3 Connect your devices

Method 2 - Without WPS button

If you don’t have a WPS button on your hub/router, you can set up your extender

using the web based set-up with an internet browser.

Important: Before following these instructions, make sure your computer is

not connected to the internet (unplug its ethernet cable or disconnect from

your wi- network).

Also before you start, to make this method easier for you, please write down the

default values from the label on the back of the device so you can avoid unplugging

the extender later on. There’s a space provided for this on the back

of this user guide.

1 Plug the extender into a power socket near your broadband wireless router

(e.g. in the same room). Wait 10 seconds for the extender to boot up. The light will

ash red slowly.

2 Connect your computer to the extender wirelessly:

Connect wirelessly

- Use the wireless connection software or settings on your computer to display

the list of available wireless networks in your area.

- Find your extender in the list and select it; it’s called BTWiExtndr-XXX.

- Enter your extender’s wireless key (printed on the label on the back of the

extender or as suggested you can write it down on the back of this user guide

in the space provided)

- Complete the connection on your computer.

3392 Essentials Wi-Fi Extender 300 QSG [5].indd 2 18/08/2016 12:53

Produkt Specifikationer

Mærke:	British Telecom
Kategori:	Wifi repeater
Model:	Essentials Wi-Fi Extender 300
Vekselstrømsindgangsspænding:	230 V
Vekselstrømsindgangsfrekvens:	50 Hz
Antal pr. pakke:	1 stk
Produktfarve:	Hvid
Produkttype:	Netværksgentager
Wi-Fi:	Ja
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Ethernet LAN:	Ingen
Driftstemperatur (T-T):	0 - 45 °C
Sikkerhedsalgoritmer:	AES, TKIP, WPA, WPA2
Forbindelsesteknologi:	Trådløs
Certificering:	CE
Wi-Fi-bånd:	Dual-band (2,4 GHz / 5 GHz)
Bedste Wi-Fi standard:	Wi-Fi 4 (802.11n)
Antennedesign:	Ekstern
Antenner, antal:	2
Knap til nulstilling:	Ja
WPS trykknap:	Ja
LED-indikatorer:	Ja
Kan monteres på væggen:	Ja
Strømkilde type:	Vekselstrøm
Frekvensbånd:	2.4, 5 GHz
Maksimal dataoverførselshastighed:	300 Mbit/s
Strømforsyning:	2.7 W
Datalink-protokol:	IEEE 802.11b, IEEE 802.11a, IEEE 802.11g, IEEE 802.11n