Broan 509N Manual

Broan Ventilator 509N

Læs gratis den danske manual til Broan 509N (4 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Broan 509N, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Models 508N / 509N

INSTALLATION INSTRUCTIONS

1. All electrical connections must be in accordance with local

codes, ordinances, or Canadian Electrical Code. If you are

unfamiliar with methods of installing electrical wiring, secure

the service of a qualified electrician.

2. To avoid motor bearing damage and/or noisy and unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. Use care when handling motor bracket assembly to prevent

damage to blade. Do not set down assembly with weight of

motor resting on the blade.

4. Disconnect electrical power supply before installing or servic-

ing fan.

fIG. 1

FIG. 2

TYPICAL INSTALLATION

PREPARE FAN

INSTALL FAN

FIG. 1

FIG. 2

FIG. 4

FIG. 3

This unit mounts between walls 4½” to 9½” thick. Outside housing

flange is fastened to casing strips (1 x 2’s). See Fig. 1. If sheathing

behind siding is not wood, provide extra supports between walls

(Nailed or screwed to siding).

1. Choose fan location from inside room. Make sure that wall stud

does not run through opening. Lay out hole on wall (Figure

3).

2. Transfer center of hole to outside wall.

1. Remove motor assembly by loosening mounting screws, rotat-

ing assembly and lifting motor assembly out of inner housing

(Figure 2).

2. Use care when handling motor bracket assembly to prevent

damage to blade. Do not set down assembly with weight of

motor resting on the blade.

3. Pull inner housing out of outer housing.

4. Remove wiring knockout from bottom of wiring box (provided

in plastic parts bag) (Figure 2).

NOTE

Remove bottom knockout ONLY!

3. Cut out hole on side wall.

4. Lay out 14½” square around center location transferred from

inside room (Figure 4).

Broan-NuTone Canada

Mississauga, Ontario

www.broan.ca 877-896-1119

INSTALL FAN (Cont’d)

USE AND CARE

DISCONNECT ELECTRICAL POWER SUPPLY BEFORE SER-

VICING FAN.

Always unplug the fan motor before servicing the fan. The motor

bearings on this fan are lifetime lubricated and will never need

oiling.

Clean the fan blade and motor every six months by removing

the grille, unplugging the motor, and gently vacuuming the fan

blade and motor.

Clean the grille in warm, soapy water. Use a mild detergent, such

as a dishwashing liquid. DO NOT USE ABRASIVE CLOTHS,

STEEL WOOL OR SCOURING POWDERS.

99045053A

FIG. 5

FIG. 6

5. Cut square hole in SIDING ONLY! DO NOT CUT SHEATHING

(Figure 5)! Nail down all siding ends.

6. Cut round hole for fan housing in sheathing (Figure 6).

7. Nail or screw 1 x 2 casing strips inside square opening (Figure

7).

8. Put a large bead of caulk on the inside of flange on outer

housing (Figure 8).

9. If wall is less than 8” thick, remove one or more knockouts on

outer sleeve (Figure 8). Use inner sleeve for test fit.

10. Insert outer housing through hole on outside wall and nail or

screw housing to casing strips. Caulk all around filler strips

and flange (Figure 9).

11. Run wiring to fan location. Pull wire through both sleeves (Fig-

ure 10). Insert inner sleeve into opening and fasten sleeves

together with three black sheet metal screws provided in plastic

bag.

FIG. 7

FIG. 8

30040037

FIG. 9

FIG. 5

FIG. 10

12. Attach wiring to wiring box with proper connector for type of

wire being used. Drop box into opening in housing.

13. Remove receptacle from motor plug. Snap receptacle into

wiring box cover. Make electrical connections as shown in

Figure 12.

FIG. 12

FIG. 13

14. Install wiring box cover. Use two screws provided in plastic

bag.

15.Reinstall motor assembly and plug in motor.

16. Install grille with center knob and threaded stud provided in

plastic bag. (Fig. 13)

KNOCKOUT

PANELS

Produkt Specifikationer

Mærke:	Broan
Kategori:	Ventilator
Model:	509N

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan 509N stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator Broan Manualer

Broan QTXEG110 Manual

7 August 2025

Broan ZB80L1 Manual

8 Juli 2025

Broan LP510R Manual

7 Juli 2025

Broan L500 Manual

7 Juli 2025

Broan Roomside AR80LWH Manual

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

Grunkel MET-H16 Industrial Manual

14 September 2025

Grunkel SKYWIND-42BT Manual

13 September 2025

Grunkel TF-I45W Manual

13 September 2025

Create Air Mist Manual

13 September 2025

Antari AF-3X Manual

13 September 2025

MPM MWP-32 Manual

13 September 2025

Grunkel BreezeCraft FAN-165R Manual

13 September 2025

Be Cool BC18STTIDC Manual

11 September 2025

NuTone QTXN110HL Manual

10 September 2025

NuTone 744LEDNT Manual

10 September 2025