Broan 744LED Manual

Broan Ventilator 744LED

Læs gratis den danske manual til Broan 744LED (2 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Broan 744LED, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Models 744LED / 744LEDNT Recessed Fan / Light

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If

you have questions, contact the manufacturer at the address or

telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualiﬁed

person(s) in accordance with all applicable codes and standards,

including ﬁre-rated construction codes and standards.

4. Sufﬁcient air is needed for proper combustion and exhausting of

gases through the ﬂue (chimney) of fuel burning equipment to pre-

vent backdrafting. Follow the heating equipment manufacturer’s

guideline and safety standards such as those published by the

National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage elec-

trical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to a

GFCI (Ground Fault Interrupter) - protected branch circuit.

8. Never place a switch where it can be reached from a tub or shower.

9. Install this unit in a ﬂat ceiling only.

10. For use in non ﬁre rated installations only.

11. Not for use in environmental air handling spaces.

12. CAUTION - RISK OF FIRE AND PERSONAL INJURY: 75W

MAX. LAMP. Use R30, BR30, PAR30L, or PAR30LN lamps only

(75W Max.). For wet locations (tub or shower) - use PAR30L or

PAR30LN (75W Max.) lamp only. Use no other lamp types. Do

not install a lamp indentiﬁed for use only in enclosed luminaries.

13. Do not install in a ceiling thermally insulated to a value greater

than R60.

14. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, use the cardboard protector (provided) to keep drywall

spray, construction dust, etc. off power unit.

The LED bulb used with this product twists into the bulb socket.

Do not attempt to insert or remove bulb by pushing it straight

in or pulling it straight down.

4. Please read speciﬁcation label on product for further information

and requirements.

To clean trim ring / bafe: Vacuum with a soft brush attachment or

remove trim ring / bafﬂe and clean with a soft cloth and mild soap

or detergent. Dry thoroughly before reinstalling.

To clean inside of housing: Remove trim ring / bafﬂe and vacuum

inside of housing with a soft brush attachment.

OPERATION

The fan and light can be operated using various combinations of

on/off switches and controls:

• Fan and light controlled with single on/off switch

• Fan and light controlled with separate on/off switches

• Fan controlled with timer control

• Fan controlled with speed control

See “Connect Wiring” section for various wiring options.

CLEANING

MAINTENANCE

Motor is permanently lubricated. Do not oil or disassemble motor.

See “Service Parts” section for a list and illustrations of service parts.

Two of the most common ways to connect ductwork to the unit.

PLAN THE INSTALLATION

The unit can

be installed

anywhere

between ceiling

joists using

mounting

brackets

provided.

Install in a ﬂat

ceiling only.

Typical Installation

The unit will operate most quietly and efﬁciently when located where

the shortest possible duct run and minimum number of elbows will

be needed.

Plan to supply the unit with proper line voltage and appropriate

power cable.

ROOF CAP

4-IN. ROUND

ELBOW

4-IN. ROUND

DUCT **

WALL

CAP

** Purchase separately

INSTALLATION

2. Mark mounting location.

Position unit between joists and extend mounting brackets.

IMPORTANT: Position brackets so there will be an 1/8” gap

between bottom of housing and ceiling material. Mark the top of

keyhole slot on all four mounting brackets.

COOKING AREA

Do not install above

or inside this area

Cooking

Equipment

Floor

The unit must not

be installed above or

inside the cooking

area shown.

Do not install in a cooking area.

HOUSING

MOUNTING

BRACKET

CEILING

JOIST

POWER

CABLE

TRIM RING / BAFFLE

FINISHED CEILING

4" ROUND

DAMPER/DUCT

CONNECTOR

1/8" GAP

1. Install mounting brackets.

Slide the adjustable mounting brackets into the bracket channels

on the housing.

Bend the tabs on the cardboard protector and insert protector into

opening in housing.

NOTE: The cardboard protector shields the inside of the housing

from drywall spray and construction dust. Do not remove it until

after construction is completed.

CARDBOARD PROTECTOR

Statement, or to order Service Parts: go to www.broan.com or www.

nutone.com and type the Model in the “Model Search” ﬁeld at the top of

the page. Broan, 926 W. State Street, Hartford, WI 53027 800-637-1453

3. Pound in nails.

Remove unit temporarily, and pound

nails partially into joists at all four

marked locations.

4. Hang and secure housing.

Hang unit from nails. Check to make

sure that there will be a 1/8” gap

between bottom of housing and

ceiling material. Pound nails tight.

For wide joist centers: A #8 x 3/8

self-tapping screw can be used to

join extended brackets together and

create a rigid mount. To ensure a

noise-free mount, crimp the bracket

channels tightly around mounting

brackets.

5. Attach damper/duct connector.

Snap the damper/duct connector onto housing. Make sure that

tabs on the connector lock in housing slots. (Top of damper/duct

connector will be ﬂush with top of housing.) Install ductwork.

FLUSH

NOTE: Make sure damper ﬂap is in

place inside of duct connector. If it

is not: Squeeze top and bottom of 

connector to snap ﬂap back into

place.

7. Connect wiring.

Unit can be wired from outside of housing as shown. Use UL approved

connectors to wire per local codes.

6. Choose power cable direction.

Remove wiring plate. When re-attached, the wiring plate allows the

power cable to enter unit horizontally or vertically.

HORIZONTAL POWER

CABLE CONNECTION

VERTICAL

POWER CABLE

CONNECTION

1102398A

FINISHED

CEILING

MATERIAL

HOUSING

COLLAR

CLEARANCE

HOLE

8. Finish ceiling.

Cut an opening in ﬁnished ceiling material for housing collar.

WIRING PLATE

WHITE

BLUE (FAN)

BLACK

TOP / BACK

OF HOUSING

3-WIRE PLUS

GROUND

POWER

CABLE

GROUND TO

WIRING PLATE

Fan operated with separate on/off switch,

speed control or timer.

Light operated with separate on/off switch.

Fan and Light operated with single on/off switch

BLACK (LAMP)

TO RED

WIRING PLATE

WHITE

BLUE AND

BLACK

TO BLACK

TOP / BACK

OF HOUSING

2-WIRE PLUS

GROUND

POWER

CABLE

GROUND TO

WIRING PLATE

9. Attach trim ring / bafe to housing.

Remove the cardboard protector from inside the housing collar.

Use a pencil to insert one end of each spring into the holes on the

lamp bracket. Center trim ring / bafﬂe in ceiling opening.

10. Install bulb.

SPRINGS

TRIM RING / BAFFLE

LAMP

BRACKET

CAUTION: Twist bulb to install or remove.

CAUTION - RISK OF FIRE: Use only R30, BR30, or PAR30

shaped, 10W LED bulb with GU24 base (supplied).

Replacement bulbs can be ordered from Broan if not

available locally (see service parts list).

Produkt Specifikationer

Mærke:	Broan
Kategori:	Ventilator
Model:	744LED

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan 744LED stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator Broan Manualer

Broan AE50110DCL Manual

19 Oktober 2025

Broan QTXEG110 Manual

7 August 2025

Broan ZB80L1 Manual

8 Juli 2025

Broan LP510R Manual

7 Juli 2025

Broan L500 Manual

7 Juli 2025

Broan Roomside AR80LWH Manual

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

Savio AD-02 Manual

11 December 2025

Big Ass Fans Turbo6 Manual

10 December 2025

Progress Lighting P250061 Manual

10 December 2025

Kichler 310260 Manual

10 December 2025

Progress Lighting P2599 Manual

9 December 2025

Progress Lighting P2531 Manual

9 December 2025

Maestro MR-903 Manual

9 December 2025

Maestro MR-905 Manual

9 December 2025

Maestro MR-902 Manual

9 December 2025

Lasko Whirlwind APDC301 Manual

8 December 2025