Broan AR70LC Manual

Broan Ventilator AR70LC

Læs gratis den danske manual til Broan AR70LC (2 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 64 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 32.5 anmeldelser. Har du et spørgsmål om Broan AR70LC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

OPTION -

To mount housing anywhere between ceiling framing:

Use optional Hanger Bar Kit (sold separately from local distributors or

website). Follow mounting instructions included with kit.

1. Remove blower and all packing material

from fan housing.

2. Remove wiring

panel from fan

housing.

3. Attach damper/duct connector to

fan housing.

4. Mount housing to ceiling structure.

ROOF CAP* (with built-in damper)

WALL CAP*

(with built-in

damper)

4-IN. ROUND

ELBOWS*

FAN

HOUSING

Seal gaps

around

housing.

Seal duct joints

with tape.

INSULATION

(Place around and

over fan housing.)

POWER

CABLE *

* Purchase separately.

Keep duct

runs short.

4-IN. ROUND

DUCT*

TABS

5. Connect 4-in. round duct.

ALL INSTALLATIONS

Start here.

IMPORTANT - The ducting from this fan to the outside of the

building has a strong effect on the air flow, noise and energy use

of the fan. Use the shortest, straightest duct routing possible for

best performance, and avoid installing the fan with smaller ducts

than recommended. Insulation around the ducts can reduce energy

loss and inhibit mold growth. Fans installed with existing ducts

may not achieve their rated airflow.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Acceptable for use over a tub or shower when connected to a

GFCI (Ground Fault Circuit Interrupter) - protected branch circuit

(ceiling installation only).

8. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. Please read specification label on product for further information

and requirements.

CLEANING & MAINTENANCE

For quiet and efficient operation, long life, and attractive

appearance - lower or remove grille and vacuum interior of unit

with the dusting brush attachment.

The motor is permanently lubricated and never needs oiling. If the

motor bearings are making excessive or unusual noises, replace

the blower assembly (includes motor and impeller).

OPERATION

Use a two-function control to operate this ventilator. See “Connect

Wiring” for details.

READ AND SAVE THESE INSTRUCTIONS

Push connector

through opening from

inside of housing.

Engage tabs and

secure with screw

from parts bag.

Make sure bottom of housing will

be flush with finished ceiling.

For proper location using ½”

ceiling material: Bend out

housing tabs to fit against

bottom of structure.

Secure housing through

mounting ears with

appropriate fasteners.

If mounting housing to

I-joist, use wood blocking as

shown.

NEW CONSTRUCTION INSTALLATION

HOUSING

TABS

Cooking

Equipment

Floor

COOKING AREA

Do not install above or

inside this area.

45o45o

NOT FOR USE IN

A COOKING AREA.

SERIES FAN / LIGHT

For Retrot Installation - Skip to back page.

For Warranty Statement, Service Parts, Technical Support, or to

In the United States - Broan.com 800-637-1453 or NuTone.com

888-336-6151

In Canada - Broan.ca or NuTone.ca 877-896-1119

Produkt Specifikationer

Mærke:	Broan
Kategori:	Ventilator
Model:	AR70LC

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan AR70LC stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator Broan Manualer

Broan AE50110DCL Manual

19 Oktober 2025

Broan QTXEG110 Manual

7 August 2025

Broan ZB80L1 Manual

8 Juli 2025

Broan LP510R Manual

7 Juli 2025

Broan L500 Manual

7 Juli 2025

Broan Roomside AR80LWH Manual

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

Savio AD-02 Manual

11 December 2025

Big Ass Fans Turbo6 Manual

10 December 2025

Progress Lighting P250061 Manual

10 December 2025

Kichler 310260 Manual

10 December 2025

Progress Lighting P2599 Manual

9 December 2025

Progress Lighting P2531 Manual

9 December 2025

Maestro MR-903 Manual

9 December 2025

Maestro MR-905 Manual

9 December 2025

Maestro MR-902 Manual

9 December 2025

Lasko Whirlwind APDC301 Manual

8 December 2025