Broan BNSC136BL Manual

Broan Emhætte BNSC136BL

Læs gratis den danske manual til Broan BNSC136BL (4 sider) i kategorien Emhætte. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Broan BNSC136BL, eller vil du spørge andre brugere om produktet?

Side 1/4
99045858ACVR09‐27‐2017


AdditionalInformationfor
RangeHoodsmeetingADACompliance
BroanandNuTonebrandedresidentialrangehoodscanbeinstalledtocomply
withSections308and309ofADAGuidelines,whenusedwithappropriately
mountedcontrolsinstalledat15”to48”abovethefloorandcontrolaccess
shouldnotrequirereachingoveracookingappliance.
ThefollowingrangehoodscanworkinanADACompliantsituationwhenthe
rangehoodiswiredtooperatefromadedicated,standardelectricalwallswitch.
Tofacilitatethisapplication,sharetheinformationonthefollowingpageswith
yourelectricianwhenpreparingfortheinstallation.
THISPROCEDUREAPPLIESTOTHEFOLLOWINGRANGEHOODSERIES
BroanSeries:BCS3,BCSD,BCSEK,BKSA,BKSF,BNSC,BQSEN,BQSJ,CLSC,CRSA
andCRSF
NuToneSeries:AHSA,AVSF,NCS3,NCSEK,NKSAandNQSEN
ADA HIGH VOLTAGE WIRING INSTRUCTIONS FOR SINGLE BLOWER RANGE HOODS WITH
ROCKER SWITCH CONTROL
WARNING
!
!
!
!!
For residential (domestic) installation only. Before proceeding, switch power off at service panel and lock service
disconnecting means to prevent power from being switched on accidentally. Installation work and electrical wiring
must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated
construction codes and standards. Also, it is recommended to wear safety glasses and gloves.
A CCESS TO RANGE HOOD CONTROL PANEL CONNECTIONS
Remove filters from the hood and set them aside.
NOTE: Some models have only one filter.
Remove the wiring cover (shaded part on illustration below)
retaining screw. Slide out the wiring cover from the hood and set
it aside with its screw.
Unplug the blower connector from the main harness.
NOTE: The illustrations in this procedure are generic; some hood details may slightly differ from the hood you have on hand but the
procedure itself applies to all single blower range hoods listed in this document (see page 3).
Wiring cover
screw
Using a 11/32'' socket, remove the 6 nuts retaining the blower
chamber to the hood assembly (2 nuts on inner back and 2 other
nuts per sides), then use a Phillips no. 2 screwdriver to remove
both front corner screws. See picture below for nuts and screws
locations. Pull out the blower chamber from the hood assembly
and set it aside with its retaining screws and nuts.
HE0253
HD0672
Nuts
Nuts
Screw
Remove and set aside the 4 front screws retaining the bent plate
to the hood.
HD0673
Screw locations
Fold back the bent plate to access to control panel connections.
HD0674
199045858A


Produkt Specifikationer

Mærke: Broan
Kategori: Emhætte
Model: BNSC136BL

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan BNSC136BL stil et spørgsmål nedenfor, og andre brugere vil svare dig




Emhætte Broan Manualer

Broan

Broan BCSEK136WW Manual

12 Januar 2025
Broan

Broan BKDB136WW Manual

11 Januar 2025
Broan

Broan Elite RMIP45 Manual

1 September 2024
Broan

Broan Elite 619004 Manual

1 September 2024
Broan

Broan BWS1304SS Manual

1 September 2024
Broan

Broan EWS1306BLS Manual

1 September 2024
Broan

Broan BWP1304SS Manual

1 September 2024
Broan

Broan PM250 Manual

1 September 2024

Emhætte Manualer

Nyeste Emhætte Manualer