Broan NuTone Manual

Broan Overvågningskamera NuTone

Læs gratis den danske manual til Broan NuTone (7 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om Broan NuTone, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
MODEL LA542WH
Page 1
WIRELESS DOOR CHIME
Installation & Operating Instructions
IMPORTANT: This wireless pushbutton and chime set is for
residential use, only. It will operate at an unobstructed distance
of 300 feet. Building materials may reduce operating distance.
Certain building materials; such as, but not limited to metal,
concrete, brick, stucco and foil-lined insulation; cause greater
interference than others; for example, wood or vinyl siding.
INSTALL PUSHBUTTON BATTERY
Refer to Figures 1 and 2.
1. Remove pushbutton and 3V lithium coin-battery from packaging.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its base.
3. Orient battery with “+” side viewable.
4. Insert battery into holder and press to seat.
5. Insert top of mounting base onto pushbutton and press bottom
together until mounting base snaps securely onto pushbutton.
Use only 3V (volt) lithium CR2032 style coin-battery for replacement.
INSTALL CHIME BATTERIES
Refer to Figures 3 and 4.
1. Remove chime from packaging.
2. Use finger to depress tab and remove chime cover. Set cover aside.
3. Insert three (3) 1.5V “D” alkaline batteries (not supplied) oriented as
shown on front of battery compartment.
4. Replace chime cover.
Figure 1
“PUSH”
TO OPEN COVER
3V LITHIUM
CR2032-STYLE
COIN
BATTERY
Figure 2
SLOT
“LEARN” PROCEDURE
Refer to Figure 5.
1. Set pushbutton and chime next to each other.
2. Press and release “Learn” button on chime.
3. LED lights to indicate “Learn” mode was entered.
4. Press and release pushbutton.
5. Confirm chime-tone is heard.
6. Repeat Step 4 to cycle through available chime-tones.
7. When desired chime-tone is heard, press and release “Learn” button
(Note: Chime may not respond to this button being pressed if it is too
soon after chime-tone sounds).
8. LED should turn off to confirm “Learn” mode exited.
9. Press and release pushbutton and confirm chime-tone hasn’t change
from desired one.
• Up to four (4) pushbuttons can be used with a single chime by
selecting different chime-tones for each pushbutton.
• Chime can erase all “Learned” pushbuttons and tones by pressing
and holding “Learn” button; LED will light; within 20 seconds, LED will
turn off; release “Learn” button.
DETERMINE USABLE LOCATIONS
Do not plan to mount pushbutton directly on metal or concrete
surfaces; install a 1/8-1/4” wood spacer between pushbutton and
metal or concrete mounting surface.
Some stucco houses have metal mesh in the wall structure, which
will affect the wireless chime performance.
Experiment with various pushbutton and chime locations to
determine location that gives best performance before mounting
permanently.
Chime must not be located within 1-foot of any metal.
Pushbutton and chime should be located within 300-feet of each
other.
1. Place chime near desired mounting location.
2. Select a level location and hold pushbutton in desired mounting
location.
3. Press and release pushbutton.
4. Confirm chime-tone sounded.
5. If chime-tone does not sound, temporarily affix pushbutton to
mounting surface with double-stick or folded-over tape; repeat Steps 3
and 4.
6. If chime-tone still does not sound, move location of chime closer to
pushbutton; repeat Steps 3 and 4.
Figure 3 Figure 4
Figure 5
VOLUME BUTTON
LEARN BUTTON LED
MODEL LA542WH
Page 2
Figure 6
MOUNT PUSHBUTTON
Refer to Figures 1 and 6.
1. After selecting usable locations in previous section, go to pushbutton
location.
2. Insert small, flat-blade screwdriver into bottom of pushbutton and twist
to separate its mounting base.
3. Make sure pushbutton mounting location is level.
4. Position pushbutton mounting base with “TOP” arrow correctly
oriented and mark base mounting holes locations.
5. Drill two (2) holes, 1/16” diameter if using supplied screws alone or
3/16” diameter if using supplied plastic anchors and screws, at base
mounting hole locations.
6. If 3/16” diameter holes were drilled, insert supplied plastic anchors.
7. Secure pushbutton base to mounting location with two (2) supplied
screws.
8. Make sure black O-ring is completely seated in its mounting base
groove with round edge at top and flat edge at bottom.
9. Hook pushbutton top catch onto top of base, swing pushbutton into
position and press bottom of pushbutton until it securely snaps onto
base.
SET VOLUME PROCEDURE
Refer to Figure 5.
There are four (4) volume levels which are accessed sequentially.
1. Press and release pushbutton to sound chime tone.
2. Press and release “Volume” button to hear the next volume setting.
3. If chime tone is not sounding when “Volume” button is pressed then
chime will sound a beep to indicate volume setting.
4. Volume setting cycles from loud to medium-loud, medium-soft and soft
then back to loud.
5. Repeat Step 2 until desired volume level is set.
6. Last volume setting is remembered.
7. Press and release pushbutton to sound chime tone and confirm
desired volume setting.
BASE
PLASTIC
ANCHORS
TOP
BLACK
“O” RING
MOUNTING
SCREWS
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Regulatory Information
The user is cautioned that changes or modifications not expressly
approved by the party responsible for regulatory compliance
could void the user’s authority to operate this equipment.
MOUNT CHIME
Refer to Figure 7.
1. Go to selected chime location.
2. There are two ways to mount this chime
a. Back-plate permanently mounted to wall; or
b. Back-plate removable from wall.
Select desire back-plate mounting method.
3. Measure down from top of desired chime location and mark
mounting screw(s) position(s).
a. 1-1/8” and centered, and 3-3/8” down from first mark and 1-5/16”
either side of center; or
b. 7/8” and 1-5/16” either side of center.
4. Drill holes, 1/16” diameter if using supplied screws alone or 3/16”
diameter if using supplied plastic anchors and screws, at marked
mounting screw locations.
5. If 3/16” diameter holes were drilled, insert supplied plastic anchors.
6a. Place screw through back-plate centered hole and into mounting
hole and tighten until 1/8” remains protruding.
Place (2) screws through back-plate bottom holes and into mounting
holes and tighten until snug.
Tighten top screw until it is snug.
6b. Place screws into mounting holes and tighten until 1/8” remains
protruding.
Place back-plate keyhole slots over mounting screws and apply slight
downward force to seat keyhole slot on mounting screw.
7. Hook chime top to back-plate, swing chime bottom towards back-
plate and press on front-bottom of chime until chime is secured to
back-plate.
TROUBLESHOOTING GUIDE
1. Chime does not sound:
a. If pushbutton LED doesn’t light when pushbutton is pressed then:
1. Check battery polarity in pushbutton.
2. Replace battery in pushbutton.
b. Replace batteries in chime.
c. Bring pushbutton in area of chime and test:
1. If chime sounds then change location of chime.
2. If chime does not sound then conduct erase procedure per note
at end of “Learn” Procedure then conduct “Learn” Procedure,
Steps 1 through 9.
2. Chime loses volume or changes tone: Change batteries in chime.
3. Chime sounds when pushbutton is not pressed:
a. Release pushbutton catch at bottom and check inside for signs of
moisture; check O-ring for cracks or damage.
b. Conduct erase procedure per note at end of “Learn” Procedure then
conduct “Learn” Procedure, Steps 1 through 9.
Figure 7
1/8”
7/8”
MOUNTING
METHOD SHOWN:
Back-plate
removable from wall.
See 2. b. below.

Produkt Specifikationer

Mærke: Broan
Kategori: Overvågningskamera
Model: NuTone

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan NuTone stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Broan Manualer

Broan

Broan NuTone Manual

7 August 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

3xLOGIC

3xLOGIC VX-SMBK-D Manual

12 September 2025
3xLOGIC

3xLOGIC VISIX V Manual

12 September 2025
3xLOGIC

3xLOGIC VX-2S-OP-30X Manual

12 September 2025
Geovision

Geovision GV-VS2401 Manual

12 September 2025
Geovision

Geovision GV-LPC2210 Manual

12 September 2025
Geovision

Geovision GV-FD2410 Manual

12 September 2025
Swann

Swann SWIFI-FLOCAM2 Manual

12 September 2025
Geovision

Geovision GV-UBX3301 Manual

11 September 2025
DataVideo

DataVideo PTC-140P Manual

11 September 2025
Geovision

Geovision GV-SNVR0411 Manual

11 September 2025