Broan PowerHeat BHFLED80F Manual

Broan Ventilator PowerHeat BHFLED80F

Læs gratis den danske manual til Broan PowerHeat BHFLED80F (15 sider) i kategorien Ventilator. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Broan PowerHeat BHFLED80F, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/15

MODELS BHFLED80 • BHF80

Page 1

HEATER / FAN / LIGHT

READ AND SAVE THESE INSTRUCTIONS

FIG. 1

FIG. 2

FIG. 3

FIG. 4

FIG. 5

RETAINING

SCREWS

HINGE PIN

IMPORTANT INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE INSTALLING OR USING THIS HEATER.

To reduce the risk of ﬁre, electric shock, or injury to persons, observe the following:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the

manufacturer at the address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting

means to prevent power from being switched on accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a qualiﬁed person(s) in accordance with all

applicable codes and standards, including ﬁre-rated construction codes and standards.

4. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

5. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep

combustible materials, such as furniture, pillows, bedding, papers, clothing, curtains, etc. at least

3 feet (0.9 m) from the front of the heater.

6. Extreme caution is necessary when any heater is used by or near children or invalids and whenever

the heater is left operating and unattended.

7. Do not operate any heater after it malfunctions. Disconnect power at service panel and have heater

inspected by a reputable electrician before reusing.

8. Do not use outdoors.

9. To disconnect heater, turn controls to off, and turn off power to heater circuit at main disconnect

panel (or operate internal disconnect switch, if provided).

10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause

an electric shock or ﬁre, or damage the heater.

11. To prevent a possible ﬁre, do not block air intakes or exhaust in any manner.

12. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or

ﬂammable vapors or liquids are used or stored.

13. Use this heater only as described in this manual. Any other use not recommended by the

manufacturer may cause ﬁre, electric shock, or injury to persons.

14. This product must be grounded.

15. Do not install heater in a tub or shower enclosure.

16. This product is designed for ceiling installation only. This product is designed for installation in

ceilings up to a12/12 pitch. Ductwork must point up. DO NOT MOUNT THIS PRODUCT IN A WALL.

17. Install heater at least 6 inches from ﬂoor or any adjacent wall.

18. Do not connect heater to dimmer switch or speed control.

19. Provide a separate 20 AMP circuit. Use 12 GA. power cable of type which meets code.

20. For greatest efﬁciency, install heater so heat is directed toward tub or shower area. Avoid directing

toward walls or windows.

SAVE THESE INSTRUCTIONS

PREPARATION

1. Make sure the heater assembly is unplugged from the RED receptacle.

2. Loosen the two retaining screws on the inside of the heater discharge opening. Place a screwdriver

tip between the outer wall of the discharge opening and the fan housing. Gently pry outward until

the exhaust discharge slips off the support lip on the outer housing. (FIG. 1)

3. Unhook hinge pins and lift heater assembly out of housing. (FIG. 2)

CAUTION: REMOVE THE SHIPPING RING FROM THE HEATER BLOWER INLET BEFORE OPERATING

THE HEATER.

4. Unplug the fan assembly from the BLACK receptacle.

5. Remove the mounting screw and carefully lift the fan assembly out of the housing. (FIG. 3)

6. Refer to the wiring diagram on the next page. Remove appropriate knockout(s) by inserting a

screwdriver blade into slots and bending it back and forth to break tabs. (FIG. 4)

7. Insert the adjustable mounting brackets into the bracket channels on the housing. (FIG. 5)

For Warranty Statement, Service Parts, Technical Support, or to Register your product,

please visit our website www.broan-nutone.com or call 800-558-1711.

KNOCKOUTS

Produkt Specifikationer

Mærke:	Broan
Kategori:	Ventilator
Model:	PowerHeat BHFLED80F

Har du brug for hjælp?

Hvis du har brug for hjælp til Broan PowerHeat BHFLED80F stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ventilator Broan Manualer

Broan AE50110DCL Manual

19 Oktober 2025

Broan QTXEG110 Manual

7 August 2025

Broan ZB80L1 Manual

8 Juli 2025

Broan LP510R Manual

7 Juli 2025

Broan L500 Manual

7 Juli 2025

Broan Roomside AR80LWH Manual

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

7 Juli 2025

Ventilator Manualer

Nyeste Ventilator Manualer

Savio AD-02 Manual

11 December 2025

Big Ass Fans Turbo6 Manual

10 December 2025

Progress Lighting P250061 Manual

10 December 2025

Kichler 310260 Manual

10 December 2025

Progress Lighting P2599 Manual

9 December 2025

Progress Lighting P2531 Manual

9 December 2025

Maestro MR-903 Manual

9 December 2025

Maestro MR-905 Manual

9 December 2025

Maestro MR-902 Manual

9 December 2025

Lasko Whirlwind APDC301 Manual

8 December 2025