Buffalo GC882 Manual

Buffalo Ikke kategoriseret GC882

Læs gratis den danske manual til Buffalo GC882 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Buffalo GC882, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Please read and keep indoor use only. Don’t discard

the instruction

GC882 and GC883 Aluminium Heat Shades

OPERATING INSTRUCTIONS

INTRODUCTION

1. ance Read the instructions before using the appli .

2. ing Clean Heat Shade thoroughly before and after each use following the clean

instructions provided in this manual.

ELECTRICAL REQUIREMENTS

This product should only be connected to the mains electricity supply by a qualified electrician. Hardwire the

H eat Shade into a suitable power supply with correct voltage and sufficient power capacity. Refer to the

product label (serial plate) on the warmer for voltage and wattage requirements.

SAFETY INSTRUCTIONS

1. All power must be disconnected at power source before any service procedure is performed.

2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep

combustible materials, such as drapes and other furnishings, away from appliance.

3. Extreme caution is necessary when any appliance is used by or near children and whenever the

appliance is left unattended.

4. Always disconnect appliance before cleaning, maintaining and adjusting it.

5. Do not operate any appliance with a damaged cord or plug if the appliance malfunctions or has been

dropped / Return appliance to an authorised service facility for examination, electrical or damaged.

mechanical adjustment, or repair.

6. Do not use outdoors. This appliance is not intended for wet or moist locations. Never locate appliance

where it may fall into water.

7. Avoid the use of extension cords. Do not run cord under carpeting, runners, or the like. Arrange cord away

from traffic area and where it will not create a trip hazard.

8. This appliance has electrical parts. Do not use it in areas where gasoline, paint, or flammable liquids are

used or stored.

9. This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety. Children should be

supervised to ensure that they do not play with the appliance.

10. If the supply cord is damaged, it must be replaced by the manufacturer, it’s service agent or similarly

qualified persons in order to avoid a hazard

WARNING!

s. This unit only suitable for R40 or BR40 type incandescent lamp

The warrantylamp is excluded from the .

Buffalo Telephone Helpline:- 0845 146 2887 (United Kingdom)

PREPARATION

1. Remove the Heat Shade assembly from the carton.

2. Remove tape and protective packaging from all surfaces of unit.

3. Make sure the installation site provides the proper installation

clearances for the un it

INSTALLATION

1. ” Drill a 7/16 (11mm) hole through mounting fixture.

2. shade Pass wires from the through hole in fixture.

3. shade Secure the to the fixture with nut.

4. You may unscrew the nuts to adjust the length to fit your threaded requirements.

5. The wires in this product are brown live, blue eutral and green/yellow for earth.– – n

Caution; Hot Surface.

CLEANING

NOTE: Proper maintenance plays an important part in the life span and functioning of the shade.

1. Disconnect the heat shade from the power source prior to cleaning and ensure the surface is cool.

2. ed This unit can be clean with a damp sponge and mild soap. Rinse with clean water and wipe dry.

3. Do not immerse in water or other liquid.

The heat lamp must not be cleaned by a water jet.

MAINTENANCE

HEAT BULB REPLACEMENT

NOTE: Each standard H eat Shade is suitable for a clear or infrared heat bulb rated at or below 250 watts.

1. To replace a bulb, place the switch in the OFF and shade to cool position and allow the bulb

completely.

2. Bulbs have a threaded base, Unscrew the bulb counterclockwise from the unit and replace with a new

bulb.

Disposal

EU regulations require product to be disposed of by specialist companies who remove or recycle all gasses,

metal and plastic components.

Consult your local waste collection authority regarding disposal of your appliance. Local authorities are not

obliged to dispose of commercial refrigeration equipment but may be able to offer advice on how to dispose of

the equipment locally. lternatively call the BUFFALO helpline for details of national disposal c A ompanies

within the EU.

Compliance

The WEEE logo on this product or its documentation indicates that the product must

not be disposed of as household waste. To help prevent possible harm to human

health and/or the environment, the product must be disposed of in an approved and

environmentally safe recycling process. For further information on how to dispose of

this product correctly, contact the product supplier, or the local authority responsible

for waste disposal in your area.

BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and

specifications set by international, independent, and federal authorities.

BUFFALO products have been approved to carry the following symbol:

Produkt Specifikationer

Mærke:	Buffalo
Kategori:	Ikke kategoriseret
Model:	GC882

Har du brug for hjælp?

Hvis du har brug for hjælp til Buffalo GC882 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Buffalo Manualer

19 August 2025

1 August 2025

28 August 2024

28 August 2024

28 August 2024

Buffalo A2F667-E1GX2 Manual

6 August 2024

Buffalo AD400-512M Manual

5 August 2024

Buffalo A3N1066-2GX2 Manual

29 Juli 2024

Buffalo AN333-1G Manual

28 Juli 2024

Buffalo A2F800-E1GX2 Manual

26 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Neets Touch Panel 10” Manual

27 September 2025

Advantech VEGA-320 Manual

27 September 2025

Sanus VisionMount LMT15 Manual

27 September 2025

Advantech PCE-7B19-0GA1 Manual

27 September 2025

Advantech PPC-417 EHL Manual

27 September 2025

Yato YT-73631 Manual

27 September 2025

Advantech MIC-711-ON Manual

27 September 2025

Yato YT-73832 Manual

27 September 2025

Advantech ASR-A502 Manual

27 September 2025

Draper 30883 Manual

27 September 2025