Burley 537NZ-R Manual

Burley Varmeapparat 537NZ-R

Læs gratis den danske manual til Burley 537NZ-R (11 sider) i kategorien Varmeapparat. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Burley 537NZ-R, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/11
OPERATING INSTRUCTIONS
INSTRUCCIONES DE FUNCIONAMIENTO
GEBRUIKSAANWIJZING
BEDIENUNGSANLEITUNG
NOTICE D' UTILISATION POUR MODELES
Burley Appliances Ltd., Lands End Way, Oakham, Rutland. U.K. LE15 6RB.
Telephone +44 (0)1572 756956. Fax +44 (0)1572 724390.
E-mail info@burley.co.uk www.burley.co.uk
537-R / 537E-R / 537NZ-R / 537U-R
Trim / Remate / Kader / Rahm / Cadre
838CH
Thank you very much for purchasing a Burley electric fire. Please spend a couple of minutes reading these instructions before using
the appliance, they are to ensure your safety and convenience.
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect heater, turn controls to off, then remove plug from outlet.
2. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used
or stored.
3. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric
shock, or injury to persons.
4. Do not use this appliance on an extension lead.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to
persons. These include the following:
Installation.
1. Read all the instructions before using this heater.
2. Do not locate this heater immediately below a socket outlet.
3. Do not use this heater in the immediate surround of a bath, shower, or swimming pool. Do not allow any contact with water.
4. Do not cover this heater. Do not locate near curtains etc, they could blow and cover the heater. Do not allow any flammable ob-
jects such as chairs, tables etc to be placed within six feet of the heater. Do not allow anything to restrict the airflow around the
heater, there could be a risk of overheating.
5. Do not lead the cable in front of the air outlet.
6. Do not trap the cable. Ensure that the fire is not standing on the cable.
7. Before use the appliance must be securely fixed by the method described in the following pages. Until it has been fixed in place,
do not leave it in a location where it could be accidentally knocked over by children or pets etc.
8. Do not permanently fix the appliance, it will need removing for servicing.
9. Parts of this heater are hot when in use. To avoid burns, do not touch hot surfaces.
10. Do not run the cable under a carpet or rug etc. Arrange cable away from traffic areas and where it will not be tripped over.
11. This appliance must not be used by children or other persons without assistance or supervision if their physical, sensory or men-
tal capabilities prevent them from using it safely. Children must be supervised to ensure that they do not play with or touch the
appliance. Use an approved fixed fire screen or safety guard if there is any chance that the appliance could be inadvertently
touched.
12. Do not use outdoors.
13. Do not operate any heater with a damaged cable or plug or after the heater malfunctions, or after it has been dropped or dam-
aged in any manner. Return the appliance to an authorised service agent for examination and repair.
14. Do not insert or allow foreign objects to enter the appliance as this may cause electric shock, fire, or damage to the appliance.
15. This is an imitation flame effect electric fire and must not be used as a real fire.
16. Do not sit or put loads on top of the appliance.
17. If moving do not drag the appliance as this could cause damage. Lift the appliance (with help if required), move then lower.
18. Risk of choking. The pebbles on the fire are real. Do not allow children or pets etc to eat the pebbles due to the risk of choking.
Never leave unsupervised.
19. Switch off and unplug the appliance when not in use.
Save these instructions
Commissioning your fire
Carefully unpack your electric fire, it will consist of:
Electric fire, one spacer (already fixed to frame), 2 stainless steel panels, bag of pebbles, bag of coal, and a
fixing kit.
Some models may also contain a log effect.
The trims have sharp edges. Do not allow handling without the use of cut proof gloves.
1. There are two silver transit screws located at the rear of the appliance. These must be removed before
installation. See picture right .
2. Position the electric fire following the installation instructions above. For stability you must fix the fire
into position using the fixing kit, this is to ensure that the appliance will not fall forward. Using the wall plug, attach the eye-bolt to
the wall or the back of the fireplace or wall behind the fire. Screw the fixing screws and washers partway into the hole shown in the
diagram. Wrap one end of the wire half way around the left-hand screw and tighten so the wire is trapped between the washer and
the chassis. Now pass the other end of the wire through the eye bolt. Move the fire closer to the eyebolt . It is not usually neces-
sary to have the wire taut. Thread the wire through one of the two fixing holes in the other side of the chassis, position the fire,
then pull through the wire to take up the slack and thread the wire all the way back through the other hole. Move the
fire back to the required position and check it is secure by tipping the fire forwards so the wire is supporting the
weight. Give it a small tug to ensure that it is secured.
This product also has the option of being hung from a wall using the cut out keys on the rear( ). →
The product must be secured to a wall using appropriate wall plugs.
5. Place the pebbles on the fibreglass fuel bed. If for any reason you need more
pebbles it is quite acceptable to use normal pebbles. Alternatively, you may wish to fit
the log effect instead.
Adhesive
strips
Right Side Left Side
4. Fixing the stainless steel sides to the trim. Remove the backing off the adhesive
strips and press the stainless steel sides firmly to the trim. Be careful to get them
lined up. ONCE THE SIDES ARE IN PLACE THEY CANNOT EASILY BE REMOVED.
3. The appliance comes with one removable spacer. If you would like to use the electric fire
freestanding, leave the spacer fixed to the rear of the front trim. If you have a suitably sized
fireplace opening the spacer can be removed to allow insetting.
Fixing
holes
Fixing
Wire
2 Fixing
Holes

Produkt Specifikationer

Mærke: Burley
Kategori: Varmeapparat
Model: 537NZ-R

Har du brug for hjælp?

Hvis du har brug for hjælp til Burley 537NZ-R stil et spørgsmål nedenfor, og andre brugere vil svare dig


Varmeapparat Burley Manualer

Burley

Burley 586-R Manual

21 August 2024
Burley

Burley 513 Manual

21 August 2024
Burley

Burley 537U-R Manual

21 August 2024
Burley

Burley 537-R Manual

20 August 2024
Burley

Burley 537NZ-R Manual

19 August 2024
Burley

Burley 515 Manual

19 August 2024
Burley

Burley 520 Manual

18 August 2024
Burley

Burley Lyddington 101 Manual

18 August 2024
Burley

Burley Welham 1832 Manual

18 August 2024
Burley

Burley 224 Manual

18 August 2024

Varmeapparat Manualer

Nyeste Varmeapparat Manualer

N'oveen

N'oveen CH9000 Manual

1 August 2025
N'oveen

N'oveen FH-03 Manual

1 August 2025
Emos

Emos ZU133 Manual

1 August 2025
Emos

Emos ZT1521E Manual

31 Juli 2025
ProfiCare

ProfiCare PC-GKH 3119 Manual

31 Juli 2025
Meaco

Meaco Heat Motion Eye 1.8kW Manual

31 Juli 2025
Emos

Emos ZT1621E Manual

31 Juli 2025
Emos

Emos ZU166 Manual

31 Juli 2025
ProfiCare

ProfiCare PC-GKH 3118 Manual

31 Juli 2025
Cecotec

Cecotec Readywarm 9820 Force Dual Manual

31 Juli 2025