Byron SX-15 Manual

Byron Dørklokke SX-15

Læs gratis den danske manual til Byron SX-15 (2 sider) i kategorien Dørklokke. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Byron SX-15, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Wire Free Battery Bell Kit

SX-15

The wirefree battery bell kit consists of two

separate units:

1. Push button unit (Transmitter)

2. Door chime unit (Receiver)

These units are completely self-contained

and no wiring between them is necessary.

No wiring is required for this wirfree door bell

kit. When the push button is pressed, it sends

a wirefree signal to activate the door bell.

As the operating range is up to 100 metres

(320 ft. approx.), you can mount the door bell virtually

anywhere in the home, workshop, or oﬃce. However,

the operating range of the wirefree signal will be

reduced if the signal is transmitted through a number

of walls or ceilings. Metal, and UPVC doorframes will

also reduce the operating range.

Installation

Push button unit

1. The push button unit is operated by 2 x 3 volt

Lithium batteries (CR2032 - ).included

2. Remove the back of the case by pushing in the tab

on the bottom with a small, ﬂat screwdriver.

3. 2 x 3 volt Lithium batteries (CR2032) have been

installed. Simply pull oﬀ the isolating strip to allow

the batteries to make electrical contact.

4. Snap the front cover of push button back on and it

is ready to use.

Replacing the batteries. Remove the locking screw

from the battery fastener in the battery compartment.

Insert 2 x 3 volt Lithium batteries (We recommend

Byron model SX-100 - ), ensure thenot included

battery’s polarity matches the internal markings.

Tighten the screw on the battery fastener to hold the

batteries ﬁrm in their compartment. Test to see if the

L.E.D. light comes on.

UM-1

“D”

R20

UM-1

“D”

R20

Installation Guide

a) Bell Push Unit: Using the two holes on the back of push button

as a template,mark the ﬁxing position for the unit. Drill holes,

ﬁt wall plugs (if ﬁxing to masonry) and secure the Bell Push

Unit with screws (self-tapping N3 x 16mm screws - )included

in position, alternatively use the double-sided self-adhesive

pad ( ), by placing onto your front doorframe or aincluded

position nearby. Please note, the latter is not the most theft

resistant option.

Important: Mounting the push button unit onto UPVC doorframes

or metal surfaces will reduce the operating range.

b) Door Chime Unit: This has a slotted hang hole on the rear,

this hole will enable the chime unit to be hooked onto a

screw and be easily removed or relocated to another room.

Drill a hole and ﬁt wall plug (if ﬁxing to masonry) and screw (self-tapping N3

x 16mm screw ) to ﬁxing position. Leave a gap of 3mm between theincluded

screw head and the wall. Locate the keyhole slot on the back of the unit over

the screw.

Battery Bell unit

1. Remove the front cover, insert 2 x 1.5 volt alkaline

batteries (“D”, UM1, R20 size not supplied) into the

battery compartment, ensuring the battery polarity

match the internal markings.

2. Snap the front cover back on, the chime unit is ready

to use.

NOT TO BE USED WITH A TRANSFORMER.

Channel Selection

The unit comes from the factory on a pre-set

radio frequency channel. However, should

your door chime activate intermittently for no

reason at all, it is possible that a similar unit

is operating nearby on the same frequency.

The encoded frequency of the push button

(transmitter) and Door Chime (receiver) can

be changed to avoid this problem.

1. Remove the back of the caseBell Push:

by pushing in the tab on the bottom with

a small, ﬂat screwdriver.

Door Chime Unit: Slide open the battery compartment.

2. There is 4 position dip switch marked 1,2,3,4. Use a small screwdriver to

alter the dip switch levers to the “On” or “Oﬀ” position, which can be altered

to achieve total sixteen (16) possible channels.

This

way

CR2032 x 2

Door Bell Operation

Press the button on the push button unit once, the LED indicator will light up

during signal transmission for 1 second and the door chime unit will sound.

The sound will stop as soon as the melody ends. For repeat sound, press the

button again. Holding the button in will NOT repeat the sound.

Sound Adjustment

To slightly adjust the sound of the bell, loosen the screw

that holds the dome in place. Turn the dome and then

tighten the screw.

Important

1. Do not mount the Push Button unit onto any metal or

UPVC doorframe as this will reduce the operating

range.

2. Do not immerse either unit in water.

3. Do not expose either unit to high temperatures or

close to ﬁreplace.

4. Do not use diﬀerent type of batteries, or mix up old

and new batteries.

5. Do not leave exhausted batteries in either unit. If leaving the doorbell for a

long period of time, remove the batteries from all compartments to prevent

leakage.

6. The chime unit is designed for internal use only.

7. Please dispose of old, defective batteries in an environmentally friendly

manner in accordance with the relevant legislation.

8. The unit should not be exposed to or placed near sources of water or direct

heat.

9. Replace batteries only with the same or equivalent type recommended by the

manufacturer.

10. Do not place near a P.I.R. which may interfere with your chime.

3. Select any combination ensuring it is set to the same code on pushboth

button and door chime units. E.g. If the 1 & 2 dipswitches are down in

your push button, then the 1 & 2 dipswitches must be down in your

chime unit.

4. Test to ensure correct operation before ﬁnal installation.

Trouble Shooting & User Hints

Problem

Chime does not

sound but LED

lights on Push

Button

Possible Causes

1. Units is out of range (max.

range 100m)

2. Push button and chime not

on same channel

Suggested Remedy

Operate the Chime unit within the

operation range (100m)

Re-set the channel (see Channel

Set Up)

Chime does not

sound plus no

lights on Push

Button LED

1. Flat push button battery

2. Wrong polarity of battery in

push button

3. Remove the protective Strip.

Change the battery

Re-insert battery as internal

marking in right polarity

Chime sounds

without push

button being

pressed

A similar wirfree door chime

product is operating nearby

on the same transmitter

frequency

Change transmission channel

(see Channel Set Up)

NOTE: There are no serviceable parts in the unit, do not attempt to repair it.

Speciﬁcation

A. Push Button unit

Power

Consumption

: 2 x 3volt Lithium batteries (CR2032 - included, replace with

Byron model SX-100)

: 3.0mA - ON

0.003mA - OFF

B. Door Chime unit

Power

Consumption

Operating Temperature

Operating Distance

Selectable Channel

: 2 x 1.5volt batteries (“D”, R20 or UM1 - not included)

Alternatively powered by A/C-D/C 9volt 300mA

adaptor (Byron model SX-36 - not included)

: 100mA - ON

0.3mA - Stand-by

: -10 C to +40 C° °

: 100 metres (320 feet approx.) in open ﬁeld

: Total sixteen (16) possible channels

Produkt Specifikationer

Mærke:	Byron
Kategori:	Dørklokke
Model:	SX-15

Har du brug for hjælp?

Hvis du har brug for hjælp til Byron SX-15 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Dørklokke Byron Manualer

Byron DBY-23512 Manual

4 Oktober 2024

Byron B432E Manual

4 Oktober 2024

Byron 10.015.46 Manual

1 Oktober 2024

Byron DB304 Manual

23 September 2024

Byron DBY-24112 Manual

23 September 2024

Byron BY102 Manual

22 September 2024

Byron B411E Manual

22 September 2024

Byron 10.020.40 Manual

21 September 2024

Byron 10.020.06 Manual

10 September 2024

Byron 7720 Manual

10 September 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

Eura WDP-42A3 Manual

15 Juni 2025

ORNO OR-DOM-YR-934 Manual

15 Juni 2025

ORNO OR-DOM-BA-936 Manual

15 Juni 2025

ORNO OR-DOM-BA-935 Manual

15 Juni 2025

ORNO OR-DB-KD-178 Manual

15 Juni 2025

ORNO OR-DP-MR-176 Manual

15 Juni 2025

ORNO OR-DB-KD-177 Manual

14 Juni 2025

Franke FTC 912 XS LED1 Manual

9 April 2025

Philips HSP5310 Manual

11 Marts 2025

Cata VK 9000 X Manual

22 Februar 2025