Byron SX-60I Manual

Byron Dørklokke SX-60I

Læs gratis den danske manual til Byron SX-60I (1 sider) i kategorien Dørklokke. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Byron SX-60I, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

CR2032 3V

Lithium Battery

Remove

Isolation

Strip

Push Button

• Open up the push button by pushing in the tab on the

bottom of the push with a small flat screwdriver.

• Remove the isolation strip from the battery

compartment then it is ready to use.

• When replacing the battery, ensure the battery polarity

matches the internal markings (“+” facing upwards),

then press the battery down so that it is sitting firmly in

its compartment.

Victorian Bell

Insert 4 x 1.5volt alkaline batteries (“C”, UM2 & LR14

- not included) into the battery compartment at the back

of the Bell unit, ensuring the battery polarity matches the

internal markings.

IMPORTANT: NOT TO BE USED WITH A TRANSFORMER

Push Button Installation

• Using the holes on the back of push button as a

template, mark the fixing position for the unit.

• Drill holes and fit wall plugs and secure the push button

unit to the wall with screws.

• Do not mount it on any metal surface or UPVC door

frame.

Door Chime Installation

• Drill two holes, fit a wall plugs and screws.

• Leave a gap of 3mm between the screw head and wall.

• Locate the keyhole slots on the back of the chime unit

over the screws.

Operation

• Press the button on the Push Button unit once, it sends

a wireless signal to the Bell unit, the Bell unit will sound.

• Operate the Bell unit within the operation range, test it

before final installation.

Digital Code Set Up

• Press the Push Button once, a new operation code is

generated randomly and sent to the Chime unit.

• The Bell unit will sound to indicate that a new operation

code is registered and memorised.

Wire Free Victorian Bell Kit SX-60i

100m

1 2 3 4

5 6

Push Button unit

Power: 1 x 3volt Lithium battery (CR2032 - included)

Door Chime unit

Power: 4 x 1.5volt alkaline batteries (“C”, UM2 & R14 - not included)

Door Chime Operation

Press the button on the Push Button once, it sends a wireless signal to the Victorian Bell unit and it

will sound. For repeat sound, press the button again. Hold the button in will repeat the sound.NOT

Digital Code Set Up

The Victorian Bell kit is equipped with an advanced random and self-learning operation coding

ability therefore no setting is needed. Read the following instructions before use.

1. First time operation:

After battery installation on the Push Button and Victorian Bell units, press the Push Button once

and it will generate a new operation code randomly and send a wireless signal to the Victorian

Bell unit. The Bell unit will sound to indicate that a new operation code is registered and

memorised.

2. Interference from a similar unit operating nearby:

a) Simply remove the batteries from the Push Button and Victorian Bell units and rest for 10

seconds, this will erase the memory.

b) Insert the batteries into the Push Button and Victorian Bell units. Press the Push Button once,

it will generate a new operation code randomly and send a wireless signal to the Victorian Bell

and it will sound to indicate that a new operation code is registered and memorised.

3. Front and back door Push Button operation:

a) Remove the batteries from the Push Buttons (Front & Back Door) and Victorian Bell units and

rest for 10 seconds, this will erase the memory.

b) Insert the batteries into the Push Buttons and Victorian Bell units. Press the front door Push

Button once, it will generate a new operation code randomly and send a wireless signal to the

Victorian Bell unit and it will sound to indicate that a new operation code is registered and

memorised.

c) After, (within 2 minutes) press the back door Push Button once, it will generate a new

operation code randomly and send a wireless signal to the Victorian Bell unit and it will sound

to indicate that a new operation code is registered and memorised. The Victorian Bell unit has

the ability to memorise both operation codes.

d) Test to ensure correct operation before final installation.

Important

1. Do not mount either unit close to fireplace or expose to high temperatures.

2. Do not expose the Victorian Bell unit to direct sunlight or moisture

3. Always use alkaline battery. Please dispose of old, defective batteries in an environmentally

friendly manner in accordance with the relevant legislation.

4. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit.

5. The unit should not be exposed to dripping or splashing and no objects filled with liquids, such

as vases, should be placed on the unit.

Byron No.SX60i Size: A4 Date: 15 Oct 2007

6. Replace only with the same or equivalent type of battery that is recommended by the CAUTION:

manufacturer.

7. Make sure batteries are installed correctly as per the internal markings.CAUTION:

8. Danger of explosion if battery is incorrectly installed or replaced.CAUTION:

9. IMPORTANT: There are no serviceable parts in the units, do not attempt to repair it.

User Hints

If the Bell unit does not sound, please check the following:

a) Flat batteries in either Push Button or Victorian Bell units - change the batteries.

b) Wrong battery polarity in either Push Button or Victorian Bell units - re-insert the batteries.

c) Push Button and Victorian Bell units are not on the same operation codes - re-set the code (see

digital code set up).

d) Units are out of range - Operate the Victorian Bell unit within the operation range.

Specification

Operating Temperature: -10C - +40C

Operating Distance: 100metre (330ft approx. - in open field & at suitable condition)

Selectable Digital Code: Total two hundred fifty six (256) possible digital codes

“Type R2 Device - device where the sound output is created by the initial operation of the control

and where the period of sound output continues for the designed duration irrespective of condition

of the control.”

Important:

• Make sure new set of alkaline battery is used in first

time operation.

• Make sure the batteries are installed properly and

the battery polarities match the internal markings.

• Change the frequency digital codes if door chime

activate intermittently for no reason at all (see

digital set up).

• Do not use the Chime unit with transformer

433MHz

R&TTE

APPROVED

CH Byron Electrical United Kingdom. www.chbyron.com

CH Byron Electrical Ltd

Byron House

34 Sherwood Rd, Astonfield

Bromsgrove, B60 3DR

Tel: 0845 2301231

e: support@chbyron.com

w: www.chbyron.com

‘C’ / LR14’ ‘C’ / LR14’

‘C’ / LR14’

3mm

Produkt Specifikationer

Mærke:	Byron
Kategori:	Dørklokke
Model:	SX-60I

Har du brug for hjælp?

Hvis du har brug for hjælp til Byron SX-60I stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Dørklokke Byron Manualer

Byron DBY-23412 Manual

4 August 2025

Byron DBY-23512 Manual

4 Oktober 2024

Byron B432E Manual

4 Oktober 2024

Byron 10.015.46 Manual

1 Oktober 2024

Byron DB304 Manual

23 September 2024

Byron DBY-24112 Manual

23 September 2024

Byron BY102 Manual

22 September 2024

Byron B411E Manual

22 September 2024

Byron 10.020.40 Manual

21 September 2024

Byron 10.020.06 Manual

10 September 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

Cata GS-600 BK Manual

27 November 2025

Dahua Technology VTO2000A-S1 Manual

14 November 2025

Extel Ding Manual

13 November 2025

Extel Carillo Plug Manual

10 November 2025

Nedis WIFICDPC11CBK Manual

3 November 2025

Extel Carillo Plug Flash Manual

1 November 2025

Extel Carillo Manual

31 Oktober 2025

Elektrobock BZ11-21 bílá Manual

5 Oktober 2025

Nexa LMLR-710 Manual

3 Oktober 2025

Nexa MLR-1922 Manual

3 Oktober 2025