Café CHS900P2MS1 Manual

Café Komfur CHS900P2MS1

Læs gratis den danske manual til Café CHS900P2MS1 (8 sider) i kategorien Komfur. Denne vejledning er vurderet som hjælpsom af 97 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 49 anmeldelser. Har du et spørgsmål om Café CHS900P2MS1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT — Save these

instructions for local inspector’s use.

• IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with consumer.

• Note to consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance

requires a qualified installer or electrician.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under warranty.

FOR YOUR SAFETY:

If you did not receive an anti-tip bracket with your purchase,

visit ).cafeappliances.com (In Canada, cafeappliances.ca

Installation Instructions

Electric Slide-In Ranges

MATERIALS YOU MAY NEED TOOLS YOU WILL NEED

(UL Listed 40 AMP)

4-Wire Cord 4’ long OR

3-Wire Cord 4’ long

Squeeze Connector

(For Conduit

Installations Only)

1 REMOVE PACKAGING MATERIALS: Failure to remove packaging

materials could result in damage to the appliance. Remove all packing parts from oven,

racks, heating elements and drawer. Also, remove protective film and labels on the outer

door, cooktop and control panel.

Drill with 1/8” Bit

Safety Glasses

Adjustable Wrench

Level

Tin Snips

Tape Measure

Pliers

1/4” Nut Driver

Questions? Visit cafeappliances.com. In Canada, visit cafeappliances.ca.

2 PREPARE THE OPENING (FOR INDOOR USE ONLY)

See illustrations for all rough-in and spacing dimensions. The range may be placed with 0”

clearance (flush) at the back wall and side walls of the cabinet.

NOTE: Use a 4’ power cord to prevent interference with

the storage drawer. Power cords 4

1»2’ to 6’ long may

have to be dressed to allow for proper drawer closing.

MINIMUM DIMENSIONS BETWEEN COOKTOP,

WALLS AND ABOVE THE COOKTOP:

A. Make sure the wall covering, countertop, flooring

and cabinets around the range can withstand the

heat (up to 200°F) generated by the range. 0” to

cabinets below cooktop and at the range back.

B. Allow 30” minimum clearance between surface units

and bottom of unprotected wood or metal cabinet, or

allow a 24” minimum when bottom of wood or metal

cabinet is protected by no less than 1/4” thick flame

retardant millboard covered with not less than No.

28 MSG sheet metal, (.015”), .015” thick stainless

steel, .024” aluminum or .020” copper.

C. This appliance has been approved for 0” spacing

to adjacent surfaces above the cooktop. However,

a 6” minimum spacing to surfaces less than 15” above the cooktop and adjacent cabinet is

recommended to reduce exposure to steam, grease splatter and heat.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space

above the cooktop should be avoided. If cabinet storage space is to be provided above the cooktop,

the risk can be reduced by installing a range hood that projects at least 5” beyond the front of the

cabinets. Cabinets installed above the cooktop must be no deeper than 16”.

Anti-Tip Bracket

Kit Included

WARNING Before

beginning the installation, switch power

off at service panel and lock the service

disconnecting means to prevent power

from being switched on accidentally.

When the service disconnecting means

cannot be locked, securely fasten a

prominent warning device, such as a

tag, to the service panel.

• A child or adult can tip the range and be killed.

• Install the anti-tip bracket to the wall or floor.

• Engage the range to the anti-tip bracket by sliding the

range back such that the foot is engaged.

• Re-engage the anti-tip bracket if the range is moved.

• Failure to do so can result in death or serious burns

to children or adults.

Tip-Over Hazard

WARNING

Both

Sides

30”

Install the

outlet box

on either

side of the C

1»4” ± 1»4”

11»8”

471»2”

26 7

»8”

w/o handle

291»2”

with handle

30”

3”

3” 3”

9” 8”

4”

71»2”21»4”

21»4”

Recommended

acceptable

electrical outlet

area. Orient the

electrical receptacle

so the length is

parallel to the floor.

3 ELECTRICAL REQUIREMENTS

WARNING This appliance must be properly grounded.

WARNING

All new constructions, mobile homes, recreational vehicles and installations

where local codes do not allow grounding through neutral, require a 4-conductor UL-listed range cord.

WARNING To prevent fire or shock, do not use an extension cord with this appliance.

WARNING

To prevent shock, remove house fuse or open circuit breaker before

beginning installation.

We recommend you have the electrical wiring and hookup of your range connected by a qualified

electrician. After installation, have the electrician show you how to disconnect power from the range.

You must use a single-phase, 120/208 VAC or 120/240 VAC, 60 hertz electrical system. If you

connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring

must be used.

Effective January 1, 1996, the National Electrical Code requires that new construction (not existing)

utilize a 4-conductor connection to an electric range. When installing an electric range in new

construction, mobile home, recreational vehicle, or an area where local codes prohibit grounding

through the neutral conductor, refer to the section on four-conductor branch circuit connections.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven

according to governing codes could result in a hazardous condition. If there are no local codes,

your oven must be wired and fused to meet the National Electrical Code, NFPA No. 70 – latest

edition, available from the National Fire Protection Association.

This appliance must be supplied with the proper voltage and frequency, and connected to an

individual, properly grounded, 40 amp (minimum) branch circuit protected by a circuit breaker or

time-delay fuse.

Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be provided with

ring terminals on wire and a strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord

is not recommended but if used, it should be marked for use with nominal 1

3»8” diameter connection

openings. Care should be taken to center the cable and strain relief within the knockout hole to

keep the edge from damaging the cable.

The rating plate is located on the oven frame or on the side of the drawer frame.

NOTE: Use of automatic, wireless or wired external switches that shut off power to the appliances,

are not recommended for this product.

Rating plate

SINGLE OVEN

POWER CORD AND CONDUIT INSTALLATION

A Remove wire cover (on the back of range) by removing screws using a 1/4” nut driver. You

can access the terminal block by either removing a terminal block cover (on some models) or

the wire cover. Do not discard these screws.

B For power cord and 1” conduit only, remove

the knockout ring (13»8”) located on bracket

directly below the terminal block. To remove

the knockout, use a pair of pliers to bend the

knockout ring away from the bracket and

twist until ring is removed.

D For 3/4” conduit installations only, purchase a squeeze connector matching the diameter

of your conduit and assemble it in the hole. Insert the conduit through the squeeze connector

and tighten. Allow enough slack to easily attach the wires to the terminal block. NOTE: Do

not install the conduit without a squeeze connector. The squeeze connector MUST be

installed before reinstalling the rear terminal block.

Knockout

ring in

bracket

Knockout ring

removed

Terminal block

(appearance

may vary)

C For power cord installations only (see

the next step if using conduit), assemble

the strain relief in the hole. Insert the

power cord through the strain relief and

tighten. Allow enough slack to easily

attach the cord terminals to the terminal

block. If tabs are present at the end of

the winged strain relief, they can be

removed for better fit.

NOTE: Do not install the power cord

without a strain relief. The strain relief

bracket MUST be installed before

reinstalling the rear range wiring cover.

Power cord

Strain relief

Terminal

block

Bracket

Squeeze

connector Terminal block

Conduit Bracket

Proceed to step 6 or 7.

Rear of Range

Terminal

Block Cover Screws to

remove terminal

block cover

Produkt Specifikationer

Mærke:	Café
Kategori:	Komfur
Model:	CHS900P2MS1

Har du brug for hjælp?

Hvis du har brug for hjælp til Café CHS900P2MS1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Komfur Café Manualer

Café C2S950P3MD1 Manual

21 Juli 2025

Café CEP90362NSS Manual

20 Juli 2025

Café CGU366P2MS1 Manual

20 Juli 2025

Café CGU366P3TD1 Manual

14 Juli 2025

Café CGU366P2TS1 Manual

11 Juli 2025

Café CGU366P4TW2 Manual

11 Juli 2025

Café CGU486P4TW2 Manual

20 Februar 2025

Café CGU486P3TD1 Manual

20 Februar 2025

Café CGU486P2TS1 Manual

20 Februar 2025

Café CEP90302TSS Manual

4 Januar 2025

Komfur Manualer

Nyeste Komfur Manualer

JennAir JIDT730SBL Manual

12 August 2025

DeLonghi YLI 61 BG Manual

12 August 2025

Haden HGS50W Manual

12 August 2025

Thermador SGRIDDLEW Manual

12 August 2025

Thermador PRI36LBHC Manual

12 August 2025

Blomberg HKRN651 Manual

12 August 2025

DeLonghi YLG 60 RFX Manual

12 August 2025

Smeg SPR36UGGAN Manual

12 August 2025

LG LSGL6335X Manual

12 August 2025

Etna KGG870ZTA Manual

12 August 2025