Carrier NSA-IMM Manual

Carrier sensor NSA-IMM

Læs gratis den danske manual til Carrier NSA-IMM (5 sider) i kategorien sensor. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Carrier NSA-IMM, eller vil du spørge andre brugere om produktet?

Side 1/5
Thermistor, Immersion
Installation and Operation
#NSA-A/CP-I-2.5- NSA-A/CP-I-4- NSA-A/CP-I-6-4X, 4X, 4X, NSA-HH/CP-I-2.5- -C NSA-HH/CP-I-4- -C PB , PB
NSA-HH/CP-I-6- -C /15/2019 PB 11
Specications subject to change without notice.
Catalog No. - - - Page of 11 808 785 01 1 5
Overview
Carrier Immersion Thermistors provide a predictable and accurate output over the specied
temperature range. Each sensor configuration is designed and manufactured for long-term
quality and performance. Carrier incorporates standard features such as double encapsulation
and etched Teflon leads where applicable.
Part Numbers
NSA-A/CP-I- - NSA-A/CP-I-4- NSA-A/CP-I-6- NSA-HH/CP-I-2.5- -C 2.5 4X 4X 4X PB
NSA-HH/CP-I-4- -C A-HH/CP-I-6- -C PB NS PB
Specications
Number Sensing Points:
One
Storage Temperature Range:
-40 to 85 °C (-40 to 185 °F)
Operating Humidity Range:
0 to 90% RH, non-condensing
Probe Diameter | Thermowell Bore Diameter:
0.250” (6.35mm) | 0.260
Probe Material | Thermowell Material:
304 Stainless Steel | 304 Series Stainless Steel
Wire Size
22 AWG (0.65 mm)
Thermowell Instrument | Process Thread Size:
½” NPS (National Pipe Straight) Female Thread | ½” NPT (National Pipe
Tapered) Male Thread
Enclosure Specications
(Temperature, Material,
Flammability, NEMA/IP Ratings)
PB” Enclosure-: ABS Plastic, UL94-HB, -30 to 90 °C (-22 to 194 °F),
Plenum Rated
4X” Enclosure-: Polystyrene Plastic, UL94-V2, -40 to 70°C (-40 to 158°F),
NEMA 4X (IP 66)
Sensor Output @ 25 °C (77 °F):
(Lead Wire Colors)
10 KΩ nominal (White/Green)
Immersion Length
NSA- -2.5 NSA- -4xxx : 2.5” (63.50 mm) | xxx : 4.0“ (101.60 mm)
NSA- -6xxx : 6.25” (158.75 mm)
Probe Length
NSA- -2.5xxx : - 4.31” (109.47 mm) +/ 0.13” (3.30 mm)
NSA- -4xxx : 5.81 0.13” (3.30 mm)(147.57 mm) +/-
NSA- -6xxx : 7.81” (198.37 mm) +/ 0.13” (3.30 mm)-
Thermistor, Immersion
Installation and Operation
#NSA-A/CP-I-2.5- NSA-A/CP-I-4- NSA-A/CP-I-6-4X, 4X, 4X, NSA-HH/CP-I-2.5- -C NSA-HH/CP-I-4- -C PB , PB
NSA-HH/CP-I-6- -C /15/2019 PB 11
Specications subject to change without notice.
Catalog No. - - - Page of 11 808 785 01 2 5
Dimensional Drawing
PLASTIC BOX (-PB)
NEMA -4X (-4X)
Figure 1
Installation
Carrier’s standard Immersion sensors are made to install into a ½” NPT female thread. Typically a Threadolet or Tee is
installed into the pipe, but a hole can also be drilled and tapped.
Figure 2
The pipe/system will need to be drained, unless a Hot Tap is being used. The recommend drill size is 23/32 in. (18 mm).
Drill the hole, and tap the hole with ½”-14NPT. Always use proper thread sealants on tapered pipe threads of the
thermowell. Screw the thermowell into the Threadolet, Tee, or tapped hole, using a wrench to tighten it rmly. Rell the
system and check for leaks. Best practice is to apply thermal grease to the end of the probe, but not required. Insert and
push the sensor probe into the thermowell. Turn the sensor probe assembly clockwise to tighten down completely. Refer
to the to make necessary connections. Wiring Instructions


Produkt Specifikationer

Mærke: Carrier
Kategori: sensor
Model: NSA-IMM

Har du brug for hjælp?

Hvis du har brug for hjælp til Carrier NSA-IMM stil et spørgsmål nedenfor, og andre brugere vil svare dig