Casio 2821 Manual
Læs nedenfor 📖 manual på dansk for Casio 2821 (4 sider) i kategorien Ur. Denne guide var nyttig for 51 personer og blev bedømt med 3.6 stjerner i gennemsnit af 26 brugere
Side 1/4
Operation Guide 2548/2821
1
MA0309-EA
About This Manual
• The operational procedures for Modules 2548 and 2821
are identical. All of the illustrations in this manual show
Module 2548.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Module 2821
(Light)
Module 2548
• Module 2821 does not display an AM indicator (A).
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Timekeeping Mode World Time Modee-DATA MEMORY Mode Stopwatch ModeCountdown Timer ModeAlarm Mode
Press .
City code
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
Read This Before You Set the Time and Date !
The times displayed in the Timekeeping Mode and World
Time Mode are linked. Because of this, make sure you
select a city code for your Home City (the city where you
normally use the watch) before you set the time and date.
Seconds
Hour : Minutes
PM indicator
Day of week
Month – Day
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Minutes
12/24-Hour
Format
Seconds City Code Hour
YearDay
DST
Month
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Screen
50
OFF
TYO
P10:58
12H
2003
6-30
To do this:
Reset the seconds to 00
Toggle between Daylight Saving Time (0N)
and Standard Time ( )0FF
Change the city code
Change the hour or minutes
Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping
Change the year
Change the month or day
Do this:
Press .D
Press .D
Use
D B (east) and (west).
Use
D B (+) and (–).
Press .D
Use
D B (+) and (–).
•
For full information on city codes, see the City Code Table“ ”.
• See “Daylight Saving Time (DST)” for details about DST setting.
4. Press A to exit the setting screen.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the (AM) indicator appears for times in the rangeA
of midnight to 11:59 a.m. Note that Module 2821 does not display an AM indicator
(A).
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time
(ON displayed) and Standard Time (
OFF displayed).
• Note that you cannot switch between Standard Time
and Daylight Saving Time while GMT is selected as
the Home City code.
4. Press A to exit the setting screen.
• The indicator appears on the display to indicateDST
that Daylight Saving Time is turned on.
e-DATA MEMORY
You can use the watch s e-DATA MEMORY to store e-mail’
addresses, Web page URLs, and other text data.
You can also use a password to limit access to e-DATA
MEMORY contents.
• All of the operations in this section are performed in the
e-DATA MEMORY Mode, which you enter by pressing
C.
e-DATA MEMORY Management
e-DATA MEMORY can hold up to 315 characters total,
while each record can contain up to 63 characters. The
maximum number of records depends on the number of
characters per record, as shown below.
• 63 characters per record: 5 records
• 7 or fewer characters per record: 40 records
To create a new e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, press D B and at the
same time to display the remaining memory screen.
• If 0 % is shown for remaining memory, it means that
memory is full. To store another record, you will first
have to delete some of the records stored in memory.
2. Hold down A until the flashing cursor ( #) appears on
the display, which indicates the setting screen.
• The setting screen also shows the record number that
is automatically assigned to the new record.
3. Input the text you want.
• When inputting the text, use D B (+) and (–) to
cycle through characters at the current cursor
location, and to move the cursor to the right. SeeC
“Inputting Text”.
Record number
(Page number)
Text
Remaining memory (%)
4. Press A to store your data and return to the e-DATA MEMORY record screen
(without the cursor).
• Pressing A causes the message SET to appear for about two seconds as the
data is stored. After that, the e-DATA MEMORY record screen appears.
• The text can show only three characters at a time, so longer text scrolls
continuously from right to left. The last character is indicated by the symbol s after
it. Press to stop and restart scrolling.A
• Records are stored in memory in the sequence they are created.
Operation Guide 2548/2821
2
To recall e-DATA MEMORY records
In the e-DATA MEMORY Mode, use ) to cycle through e-DATAD (+) and B (–
MEMORY records as shown below.
Press .
Press .
Remaining
memory
screen
Record 1
( )
Record 2
( )
Password
setting
screen
Remaining Memory Screen Password Setting Screen
• The value on the remaining memory screen is the percentage of memory that
is still available. It does not indicate the number of records that can be stored.
• The Password Setting screen shows xxxx when a password is already
registered.
• You can use the Password Setting screen to register, edit, or delete your
password. See Using a Password to Protect e-DATA MEMORY Data“ ” for
more information.
To edit an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D B (+) and (–) to display the record
you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D B (+) and (–) to change the character.
5. After making the changes you want, press A to store them and return to the
e-DATA MEMORY record screen.
To delete an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D B (+) and (–) to display the record
you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
• The message CLR appears to indicate that the record is being deleted.
After the record is deleted, the cursor appears on the display, ready for
input.
4. Input data or press A to return to the remaining memory screen.
Using a Password to Protect e-DATA MEMORY Data
You can register a 4-digit password to keep e-DATA MEMORY data secure.
Important!
Use a 4-digit password that is easy for you to remember, but difficult for others
to decipher. If you forget the password, you will have to have your watch
initialized (which deletes all data in memory) in order to access the e-DATA
MEMORY again. To have the watch initialized, contact the store or dealer where
you purchased it, and ask to have the AC operation performed.
To register a new password
1. In the e-DATA MEMORY Mode, use D (+) and
B (–) to display the Password Setting screen.
• This displays a screen that shows SET PA55.
2. Hold down A for about one second until NEW
appears, with the first 0 flashing.
• This is the New Password Setting screen.
3. Use D B (+) and (–) to scroll through numbers at the first digit.
4. When the first digit is the number you want, press C to advance to the next digit.
5. Repeat steps 3 and 4 to input all four digits of the password you want.
• Pressing A while inputting a new password clears your input and returns to the
Password Setting screen.
6. After all four of the password digits are the way you want, press C to register
them.
• Pressing C causes the message SET to appear for about one second as the
password is stored. After that, the Password Setting screen appears.
• After registering a password, you can input, recall, edit and delete data, if you want.
After you exit the e-DATA MEMORY Mode, you will have to input the password
every time you want to enter it again.
To input the password
1. Enter the e-DATA MEMORY Mode.
2. On the Password Input screen ( xxxx PA55 ), press D
or B. This causes the first digit of the password to
flash.
3. Input the password.
• Use D (+) and B (–) to scroll through numbers at
each digit.
• Press C to advance to the next digit.
• Pressing A while inputting the password clears your
input and returns to the Password Input screen.
4. After the password is the way you want, press C.
• If the input password matches the one registered, the message OK!appears,
followed by an e-DATA MEMORY screen.
• If the password does not match, the message ERR appears, followed by the
Password Input screen.
To change the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D B (+) and (–) to display the Password Setting screen.
3. Perform the procedure starting from step 2 under “To register a new password to”
specify the new password.
To delete the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D B (+) and (–) to display the Password Setting screen.
3. Hold down A for about one second until NEW appears, with the first 0 flashing.
4. Press B and D at the same time to delete the password.
• The message CLR appears to indicate that the password is being deleted. After the
password is deleted, the Password Setting screen appears.
World Time
World Time shows the current time in 27 cities (29 time
zones) around the world.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city code
In the World Time Mode, press to scroll through cityD
codes (time zones) to the east or to scroll to the west.B
• For full information about city codes, see the “City Code
Table”.
• If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City code settings
and make the necessary changes.
• When the currently selected time zone is one that includes
mostly ocean, a value indicating the zone s Greenwich’
Mean Time differential appears in place of a city code.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use B D and to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A for about one second to toggle Daylight
Saving Time (DST displayed) and Standard Time (DST
not displayed).
• The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
• Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT is selected as the city code.
Current time in the zone
of the selected city code
Timekeeping
Mode time
City code
Alarms
You can set up to five independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms is a snooze alarm, while the
other four are one-time alarms. You can also input
reminder text that appears when the alarm time is
reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered AL1through
AL4 for the one-time alarm, a snooze alarm screen
indicated by SNZ. The Hourly Time Signal screen is
indicated by SIG.
• In the case of the snooze alarm screen, the snooze
alarm indicator ( ) appears in the lower right corner
of the display.
• Alarm settings (and Hourly Time Signal settings) are available in the Alarm Mode,
which you enter by pressing C.
Alarm Types
The alarm type is determined by the settings you make, as described below.
• Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
• Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
• 1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
• Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1. In the Alarm Mode, use D and B to scroll through the
alarm screens until the one whose time you want to set
is displayed.
Press .Press .
• To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1 AL4through . To set the snooze alarm, display the screen indicated
by SNZ.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Press C to move the flashing in the sequence shown below to select other settings.
Hour TextMinutes Month Day
• Selecting the text causes the text input cursor ( #) to appear. There are eight
spaces in the text, so you have to press eight times to move to the HourC
setting.
Alarm time
(Hour : Minutes)
Alarm number
Timekeeping Mode time
Produkt Specifikationer
| Mærke: | Casio |
| Kategori: | Ur |
| Model: | 2821 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Casio 2821 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ur Casio Manualer
7 April 2025
7 April 2025
30 Marts 2025
22 December 2024
22 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
Ur Manualer
- Ur Just
- Ur TW Steel
- Ur Maurice Lacroix
- Ur Nokia
- Ur Junghans
- Ur WoodWatch
- Ur Edox
- Ur Nixon
- Ur Ice Watch
- Ur Cresta
- Ur Stauer
- Ur Audemars Piguet
- Ur TFA Dostmann
- Ur Lydion
- Ur ADE
Nyeste Ur Manualer
9 Juni 2025
8 Juni 2025
8 Juni 2025
7 Juni 2025
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025